Robot Vacuum Coverage Checker for a Large Home

Pick your model to fill in its published runtime, recharge-and-resume, and recharge time. You can change any value after picking. Specs come from the manufacturer pages listed in the sources below.

Cleanable home area



sq ft

Cleanable floor only: the rooms the robot can reach. Measure the floor the robot actually travels, not the listing size, which counts walls, closets, and space under heavy furniture.

Carpet share of the floor



% carpet

The share of your cleanable floor that is carpet or rugs. Carpet slows the robot: this checker cleans carpet at 75 percent of the hard-floor rate.

Runtime per charge



minutes

The rated runtime on one charge, from the spec sheet. Use the vacuum-only figure: mopping modes run shorter. If your robot is a few years old, its battery holds less than the rated figure.

Cleaning rate



sq ft per min

How fast the robot covers floor, in square feet per minute. eufy puts the average at about 10 minutes per 100 sq ft, which is 10 sq ft per minute. If the maker claims a coverage area, divide it by the runtime to get the rate.

Efficiency factor



%

The share of the robot’s travel that covers new ground. Overlap, turns, and navigation around furniture mean some travel is wasted, so 85 percent is the default. Use 70 to 75 percent for a cluttered or furniture-heavy home.

Does the robot return to its dock when the battery runs low and pick up where it left off? Most mapping robots do. Budget bump-navigation robots usually do not.

Recharge time



minutes

How long a full recharge takes, in minutes. Common figures are 2 to 4 hours; check the spec sheet. This only matters when the home needs more than one charge.


Estimated coverage per charge

1,698 sq ft

This tool provides estimates for general guidance only. Runtime and coverage figures are manufacturer claims measured in lab conditions, and real homes with carpet, furniture, and clutter clean slower and cover less per charge. Always check the manufacturer's specifications before buying.

Quick answer: Most robot vacuums clean 1,500 to 2,000 sq ft on one charge, so a home over about 1,500 sq ft of cleanable floor usually needs recharge-and-resume. A 216 minute robot at 85 percent efficiency covers about 1,698 sq ft per charge on a 30 percent carpet home, which means a 2,000 sq ft home takes two charges and 7 to 8 hours including the recharge. Enter your home size, floor mix, and robot above to get your coverage per charge, charges needed, total time, and a plain verdict.

Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.

How to use the Robot Vacuum Coverage Checker

Shopping for a robot vacuum for large home cleaning starts with one question: will this robot clean my whole home on one charge, or will it need to dock and resume? The box gives you a runtime in minutes, not an answer in square feet, and the runtime alone does not settle it. This checker turns the spec sheet into a plain answer: coverage per charge, charges needed, total time including recharges, and a verdict in plain language. It works for any robot vacuum, whether you pick a preset model or enter your own robot's specs by hand.

  1. Pick your robot. Choose a model from the preset list to fill in its published runtime, recharge-and-resume, and recharge time: the eufy Omni E25, the Roborock Q7 M5+, the eufy Omni S1 Pro, the iRobot Roomba Combo 10 Max, or the Shark PowerDetect NeverTouch Pro. Every preset figure comes from the manufacturer's own page, listed in the sources below. If your robot is not on the list, pick "My own robot" and enter its specs from the box or the manufacturer's site.
  2. Enter your cleanable home area. Measure the floor the robot actually travels, in square feet: the rooms it can reach, minus the space under heavy furniture it never goes under. The listing size of your home is not the cleanable area: it counts walls, closets, and space under beds and sofas. Measure each room and add them up, less an allowance for large furniture.
  3. Set the carpet share. Enter the share of your cleanable floor that is carpet or rugs, as a percent. Carpet slows the robot down: it runs higher suction on carpet and covers ground more slowly, so this checker cleans carpet at 75 percent of the hard-floor rate. All hard floor with a few rugs is about 10 percent; carpeted bedrooms with hard living areas is usually 30 to 40 percent; carpet wall to wall is 90 percent or more.
  4. Check the runtime and the cleaning rate. The preset fills in the runtime; if you entered your own robot, use the vacuum-only figure, not the mopping figure, which is always shorter. The cleaning rate defaults to 10 sq ft per minute, eufy's published average of about 10 minutes per 100 sq ft. If the maker claims a coverage area, divide it by the runtime to get the rate.
  5. Set the efficiency and the recharge details. Efficiency defaults to 85 percent, the share of the robot's travel that covers new ground after overlap, turns, and navigation around furniture. Use 70 to 75 percent for a cluttered home. Recharge-and-resume is set from the preset; if your robot does not resume on its own, set it to No. The recharge time is the full recharge from the spec sheet, in minutes.
  6. Read your result. You get the estimated coverage per charge, charges needed, cleaning time, recharging time, total time from start to finish, the runtime a one-charge clean would need, and the verdict: fits on one charge, needs recharge-and-resume, or too small for this home. The notes compare your estimate with the manufacturer's claim, or with independent test measurements where the maker publishes none.

This checker is one of the free tools on Tools Elite. Every figure here comes from a published source listed at the bottom. If you are sizing other appliances by room size, our Air Purifier Size Calculator and Dehumidifier Size Calculator work the same way. The checker gives estimates for general guidance, not a guarantee for any one home, so always check the manufacturer's specifications for your model before you buy.

How it works

The checker works in five steps: it adjusts the cleaning rate for your floor mix, it applies the efficiency factor, it multiplies by the runtime to get the coverage per charge, it divides your home by that coverage to get the number of charges, and it adds the recharge time to get the total time from start to finish.

Step 1: adjust the rate for carpet. Carpet costs speed. The checker cleans carpet at 75 percent of the hard-floor rate, so the effective rate is the cleaning rate times a floor factor of 1 minus 0.25 times the carpet share. A home that is 30 percent carpet has a floor factor of 0.925, so a 10 sq ft per minute rate becomes 9.25 sq ft per minute. The 75 percent carpet rate is this checker's own modeling rule, stated openly here: no manufacturer publishes a carpet speed penalty, but every robot runs higher suction and slower passes on carpet. If your home is all hard floor, this step changes nothing.

Step 2: apply the efficiency factor. A robot never covers new ground with every minute of travel: it overlaps its own paths, turns at walls, navigates around chair legs, and re-covers strips it already cleaned. The efficiency factor is the share of travel that covers new ground, and the net rate is the effective rate times the efficiency. At the default 85 percent, a 9.25 sq ft per minute effective rate becomes 7.86 sq ft per minute of new ground.

Step 3: work out the coverage per charge. Coverage per charge is the runtime times the net rate. That is the same formula a plain runtime-times-rate calculator uses, but this checker adjusts for your floor mix and your efficiency before multiplying, instead of multiplying the raw rate and calling the result real. A 216 minute runtime at 7.86 sq ft per minute of new ground covers an estimated 1,698 sq ft per charge. The same robot at the raw 10 sq ft per minute rate would claim 2,160 sq ft, which is the kind of number that disappoints people on the first run.

Step 4: work out the charges and the cleaning time. Charges needed is your home area divided by the coverage per charge, rounded up: a home that needs 1.1 charges needs 2 charges, because the robot cannot do a tenth of a charge. Cleaning time is your home area divided by the net rate, which is the time the robot actually spends moving.

Step 5: add the recharge time. Total time is the cleaning time plus one full recharge for every extra charge. A home that needs 2 charges waits through 1 recharge; a home that needs 3 charges waits through 2. This estimate assumes a full recharge between legs, which is conservative: many robots resume at a partial charge. eufy's support page says the S1 Pro resumes after recharging to 65 percent, which takes about two hours from 10 percent, so the real total is often shorter. The checker also works out the runtime a one-charge clean would need, which is your home area divided by the net rate.

Worked example: eufy E25 in a 1,800 sq ft home, 30 percent carpet. The E25 preset fills in 216 minutes of runtime, recharge-and-resume yes, and a 210 minute recharge. Floor factor: 1 minus 0.25 times 0.30, which is 0.925. Effective rate: 10 times 0.925, which is 9.25 sq ft per minute. Net rate: 9.25 times 0.85, which is 7.8625. Coverage per charge: 216 times 7.8625, which is 1,698.3, rounded to 1,698 sq ft. Charges: 1,800 divided by 1,698.3 is 1.06, rounded up to 2. Cleaning time: 1,800 divided by 7.8625 is 228.95, rounded to 229 minutes (3 hr 49 min). Total time: 229 plus one 210 minute recharge is 439 minutes (7 hr 19 min). Runtime needed for one charge: 229 minutes. Verdict: needs recharge-and-resume.

What the checker does not do. It does not model mopping, because mopping runtimes are shorter and mopping coverage depends on water tank size as well as battery: the E25 runs 125 minutes in vacuum-and-mop mode instead of 216 vacuum-only, and the S1 Pro runs about 140 minutes with mopping. If you mop, run the checker with the mopping runtime. It does not model battery aging: a lithium battery loses capacity over hundreds of cycles, so a three-year-old robot covers less than its rated runtime suggests. Multi-floor homes need one run per floor: a robot cannot climb stairs.

What your result means

The coverage per charge is the number that decides everything. Compare it with your home area: if it is bigger, one charge is enough; if it is smaller, the question becomes whether the robot resumes on its own and how many charges the home needs. The figure already includes your carpet share and efficiency, so it is a real-home estimate, not a lab number.

Charges needed tells you whether the battery fits the home. One charge means the robot finishes in a single run. Two or three charges with recharge-and-resume means it finishes on its own but takes much longer, because each recharge adds hours. More than three charges means the robot is too small for the home even with resume: a clean that needs four or more charges stretches across most of a day, and the robot spends more time docked than cleaning. Without recharge-and-resume, any home that needs more than one charge is too small for that robot, because it stops partway and waits for you to start it again.

The total time is the number people forget to check. A 216 minute robot sounds fast until the home needs two charges and the recharge adds 3.5 hours. The worked example above takes 7 hr 19 min from start to finish, of which 3 hr 30 min is charging. That is fine if the robot runs while you are at work, and a problem if you expected it done before lunch. The total is conservative: robots that resume at a partial charge finish sooner.

The runtime needed for one charge is your shopping number. If the checker says you need 229 minutes for a one-charge clean and your robot runs 180, no setting change closes that gap: you need a longer-runtime model, or you accept recharge-and-resume. If the gap is large, a hundred minutes or more, the honest fix is a bigger battery or a second robot, not a setting.

The claim comparison keeps the marketing honest. Manufacturers publish coverage claims from lab tests on open floors, and only some publish them at all. eufy claims about 1,976 sq ft per charge for the S1 Pro. Roborock, iRobot, and Shark publish no per-charge coverage figure for the models in this checker, which is why the notes show independent test measurements where they exist: Vacuum Wars measured about 1,070 sq ft per charge for the eufy E25 and estimated about 1,060 sq ft for the Roborock Q7 M5+. When the claim and the estimate differ, trust the estimate.

The verdict is a buying decision, not a grade. Fits on one charge means buy with confidence for this home. Needs recharge-and-resume means the robot works if you are comfortable with a longer clean and a robot that docks mid-run. Too small for this home means look at a longer-runtime model, split the home into zones across two days, or run one robot per floor.

Robot vacuum runtime and coverage by model

The table below is the checker's whole preset list in one place: the rated runtime, whether the model recharges and resumes, how long a full recharge takes, and what the maker claims or what independent tests measured for coverage. Where sources disagree, the table follows the manufacturer's own current page.

Model Runtime Recharge and resume Recharge time Coverage claim or test
eufy Omni E25 216 min vacuum-only; 125 min vacuum and mop Yes About 3.5 hr No maker claim; Vacuum Wars measured about 1,070 sq ft per charge
Roborock Q7 M5+ 180 min quiet mode Yes About 4 hr No maker claim; Vacuum Wars estimated about 1,060 sq ft per charge
eufy Omni S1 Pro 216 min vacuum-only; about 140 min with mopping Yes About 4 hr eufy claims about 1,976 sq ft per charge (lab test)
iRobot Roomba Combo 10 Max 175 min on hardwood Yes 2 to 3 hr No per-charge claim; 2,500 sq ft is the maximum map size
Shark PowerDetect NeverTouch Pro 110 min Yes 4 hr No maker claim published

Two rows deserve a closer look, because sources disagree on them. Roborock lists the Q7 M5+ at 180 minutes on the lowest power setting, and Vacuum Wars and TechGearLab agree, but several retail listings say 150 minutes. The checker uses 180 minutes, because that is the maker's own figure; if your Q7 M5+ runs closer to 150 minutes in your home, enter 150. The Roomba Combo 10 Max has the same kind of disagreement: iRobot's own support page lists 175 minutes on hardwood, while Vacuum Wars lists 120 minutes from the iRobot site and some retailers list 120 minutes. The checker follows iRobot's current support page at 175 minutes, and the recharge time uses the 2.5 hour midpoint of iRobot's 2 to 3 hour range.

The coverage column shows why this checker exists. Only eufy publishes a per-charge coverage claim, for the S1 Pro only. Every other maker leaves the buyer to do the arithmetic, usually runtime times rate with no adjustment for carpet, overlap, or navigation. The independent measurements show what that adjustment costs: Vacuum Wars measured about 1,070 sq ft per charge for the E25, whose 216 minute runtime times a 10 sq ft per minute rate would suggest 2,160 sq ft. The measured figure is half the naive figure, because the test ran in vacuum-and-mop mode at a real cleaning pace on a real floor plan.

Robot vacuum for large home: how much runtime do you need?

eufy's buying guide for large homes gives the clearest published answer to the runtime question. For homes under 1,200 sq ft, eufy recommends a standard battery with up to 90 minutes of runtime. For homes of 1,200 to 2,000 sq ft, it recommends a long runtime of up to 120 minutes with recharge-and-resume. For homes of 2,000 to 3,000 sq ft, it recommends a large battery with up to 180 minutes of runtime with recharge-and-resume. For homes over 3,000 sq ft on more than one floor, eufy recommends two robot vacuums. Those bands assume the robot resumes when it needs to: the runtime alone does not cover the home, and the resume feature is what finishes the job.

Run those bands through this checker and they hold up well. A 1,200 sq ft home at 30 percent carpet and 85 percent efficiency needs about 153 minutes of runtime for a one-charge clean, so eufy's 120 minute recommendation for that band is a resume recommendation, not a one-charge recommendation. A 2,000 sq ft home at the same floor mix needs about 255 minutes for one charge, which no current preset offers vacuum-only. A 3,000 sq ft home needs about 382 minutes, which is why eufy suggests two robots at that size. For a large home, recharge-and-resume is not a nice extra, it is the feature that makes the robot work at all, and the runtime decides how many charges the clean takes, not whether it finishes.

The average home size makes the same point from the other direction. eufy's guide cites an average home size in the 2020s of 2,200 to 2,300 sq ft, and says most robot vacuums are designed for medium-sized homes of around 1,500 to 2,000 sq ft. The average home is already bigger than the home most robots are designed for. For a two-floor home, one robot per floor beats one big robot carried between floors, because the robot cannot climb stairs.

Multi-floor mapping, a self-emptying dock, and a large water tank matter as much as runtime on a large home: a robot that stores one map rebuilds it on every floor, and a large home fills a small bin before the battery runs out.

Common mistakes to avoid

Multiplying the rated runtime by the rated rate and believing the answer. A 216 minute runtime times 10 sq ft per minute is 2,160 sq ft, and no real home gets that from one charge. The rate is a top speed on open floor, and the runtime is measured in the lowest suction mode on hard floor. Carpet, overlap, turns, and furniture all take their share first. Vacuum Wars measured about 1,070 sq ft per charge for the E25, roughly half the naive arithmetic.

Using the listing size of your home instead of the cleanable floor. The listing counts every square foot inside the exterior walls, including space under beds, sofas, and wardrobes that the robot never reaches. Measuring the cleanable floor takes ten minutes with a tape measure and changes the answer by hundreds of square feet.

Reading the mopping runtime as the vacuum runtime. Combo robots publish two runtimes and the mopping one is always shorter: the E25 runs 216 minutes vacuum-only and 125 minutes vacuum-and-mop, and the S1 Pro runs 216 minutes vacuum-only and about 140 minutes with mopping. If you mop, use the mopping figure. If you vacuum only, use the vacuum figure.

Confusing map size with coverage per charge. iRobot lists a coverage figure of up to 2,500 sq ft for the Combo 10 Max, and it is easy to read that as the area the robot cleans on one charge. It is not: iRobot's support page defines it as the suggested maximum map size, the largest floor plan the robot's map can hold. A robot can hold a 2,500 sq ft map and still need two charges to clean it.

Forgetting the recharge time. A robot that needs two charges does not take twice the cleaning time; it takes the cleaning time plus a full recharge, which is 2 to 4 hours on most models. A clean that looks like 4 hours of vacuuming is really 7 to 8 hours from start to finish.

Buying for suction instead of battery. Suction figures dominate robot vacuum marketing, and they matter for deep carpet cleaning, but they do not decide whether the robot finishes your home. A 20,000 Pa robot with a 110 minute battery covers less floor than an 8,000 Pa robot with a 216 minute battery. For a large home, buy runtime and resume first, then suction.

Frequently asked questions

How many square feet can a robot vacuum clean on one charge?

Most robot vacuums clean between 1,500 and 2,000 sq ft on a full charge, according to eufy's buying guide, and the average robot takes about 10 minutes to clean every 100 sq ft. Real homes come in lower: Vacuum Wars measured about 1,070 sq ft per charge for the eufy E25 and estimated about 1,060 sq ft for the Roborock Q7 M5+. eufy claims about 1,976 sq ft per charge for the S1 Pro from its own lab test.

How long does a robot vacuum take to clean 2,000 sq ft?

At eufy's average pace of about 10 minutes per 100 sq ft, 2,000 sq ft takes about 200 minutes of cleaning, and most robots need two charges to finish it, so the total is 200 minutes plus one recharge of 2 to 4 hours. A 216 minute robot at 85 percent efficiency on a 30 percent carpet home covers about 1,698 sq ft per charge, so a 2,000 sq ft home needs two charges and takes about 7 to 8 hours including the recharge.

What is recharge-and-resume, and do I need it?

Recharge-and-resume means the robot returns to its dock when the battery runs low, charges, and then picks up cleaning where it left off, with no help from you. You need it for any home the robot cannot finish on one charge, which is most homes over about 1,500 sq ft. All five models in this checker have it. Budget robots without mapping usually do not.

Does carpet reduce a robot vacuum's coverage?

Yes. A robot runs higher suction on carpet and covers ground more slowly, so a carpeted home cleans slower than a hard-floor home of the same size, and the battery drains faster on carpet. This checker cleans carpet at 75 percent of the hard-floor rate: a home that is half carpet cleans about 12.5 percent slower overall than the same home with hard floors throughout.

Why does my robot vacuum cover less than the manufacturer claims?

Manufacturer claims come from lab tests on open floors in the lowest suction mode, with no furniture, no clutter, and no carpet. Your home has all four, and each one costs range. A battery that is a few years old also holds less than its rated capacity.

How much runtime do I need for a large home?

eufy's guide recommends up to 120 minutes with recharge-and-resume for homes of 1,200 to 2,000 sq ft, and up to 180 minutes with recharge-and-resume for homes of 2,000 to 3,000 sq ft. For a one-charge clean with no resume, the need is higher: a 2,000 sq ft home at 30 percent carpet and 85 percent efficiency needs about 255 minutes of runtime, which no current model in this checker offers vacuum-only.

Can one robot vacuum clean a 3,000 sq ft home?

One robot can clean a 3,000 sq ft home if it has recharge-and-resume, but it will take several charges and most of a day: a 216 minute robot at 85 percent efficiency covers about 1,698 sq ft per charge on a 30 percent carpet home, so a 3,000 sq ft home needs two charges and about 10 hours including recharges. eufy recommends two robot vacuums for homes over 3,000 sq ft on more than one floor.

Sources

Every figure on this page comes from one of the sources below, each accessed 20 November 2026.