Pet Door Size Calculator
Your pet door size
How the answer was worked out
Size the rest of your pet's gear: our Dog Crate Size Finder works out the right crate from the same measurements, our Dog Exercise Calculator works out how much daily exercise your dog needs, and our Dog Age Calculator converts your dog's age to human years.
Last reviewed: 21 November 2026. Reviewed every 180 days; next review due 19 May 2027.
How to use the Pet Door Size Calculator
A pet door that is too small leaves your dog ducking, squeezing, and eventually refusing to use it. A pet door that is too big lets in drafts, rain, and raccoons, and it costs more than it should. The right size comes from three measurements of your pet, not from your pet's weight and not from a size name on a box. This calculator takes those three measurements, adds the clearance the manufacturers themselves recommend, and tells you the flap size you need, the matching size at each of the three biggest makers, and how high to mount the door.
The three measurements are shoulder height, width, and body depth. Shoulder height is the distance from the floor to the top of your pet's shoulders, the point horsemen call the withers. Width is the widest point of your pet, the chest or the hips, whichever is broader. Body depth is the distance from the top of the shoulders down to the bottom of the chest or belly, whichever hangs lower. PetSafe's own sizing guide asks for width and body depth and says to add one to two inches to each. Hale Pet Door asks for shoulder height and chest width and says to add an inch or two. Endura Flap asks for the height from the floor to the tallest point of the back and the width of a door opening your pet walks through comfortably. This calculator uses all three measurements because each one answers a different question: width and body depth decide how big the flap opening must be, and shoulder height decides how high the top of the flap must sit once the door is installed.
To get your result, follow these steps:
- Measure the shoulder height. Stand your pet square on level ground, all four feet planted, head in its normal position, not stretched up and not drooping. Run a tape measure from the floor straight up to the top of the shoulders. For a dog, that is the ridge between the shoulder blades. For a cat, it is the top of the shoulder blades too. Write the number down in inches. If your pet will not stand still, stand beside your pet, put your fingers level with the top of the shoulders on your own leg, and measure from the floor to that spot on your leg. Hale suggests exactly this trick on its sizing page. Enter a number from 4 to 40 inches.
- Measure the width. Find the widest point of your pet. For most dogs that is the chest, measured across the front just behind the forelegs. For some dogs, especially broad-hipped breeds, the hips are wider. Measure both and keep the larger number. If your pet is long-haired, press the tape through the coat to the body: the coat compresses as your pet passes through the flap, and measuring the fluff buys a door a size too big. Alternatively, open a door just wide enough for your pet to walk through comfortably and measure the width of the opening, which is the method Endura Flap recommends. Enter a number from 2 to 20 inches.
- Measure the body depth. With your pet standing, measure from the top of the shoulders straight down to the bottom of the chest or the belly, whichever hangs lower. For a deep-chested dog such as a Greyhound, the chest is the low point. For a round-bellied dog, the belly is. This number sets how tall the flap opening must be, because it is the height of the body that has to pass through the opening. Enter a number from 2 to 30 inches. It must be smaller than the shoulder height: the bottom of the chest sits above the floor, so a body depth as large as the shoulder height means one of the two measurements is wrong, and the calculator will say so.
- Read the headline first. The headline gives your size category and the minimum flap dimensions, for example "Your pet needs an Extra Large pet door: a flap at least 12 in wide and 16 in tall." The category is the PetSafe category, because PetSafe publishes the minimum usable opening for each size across all its doors, which makes it the conservative choice. The cards below the headline show the flap size you need, the step-over height, the height of the top of the flap, the maximum step-over for your pet, and the door the install height is based on.
- Read the maker table. The table shows the matching size at PetSafe, Endura Flap, and Hale Pet Door, with the actual flap opening at each maker. The size names do not line up between makers: a Large at one maker is a different opening from a Large at another. Buy by the flap dimensions in the table, not by the size name on the box. If the makers disagree, the guidance says so in plain language.
- Read the warnings. The calculator warns you when the step-over is too high for your pet, when PetSafe's own models disagree with its size chart for your measurements, and when your pet is wider than it is deep, which means width, not height, sets the size. A warning is not a failure: it is the calculator telling you something the size chart alone would not.
- Check the steps. The steps section prints the full working: the clearance added, the flap size needed, the smallest fitting size at each maker, and the install-height arithmetic. Every number there can be checked against a tape measure and the makers' own charts, which are reproduced in full below.
The tool updates as you type, so you can try different numbers quickly. Try the example buttons under the form: the Labrador shows a straightforward Extra Large, the Chihuahua shows how the size names disagree between makers, the Great Dane shows a pet larger than PetSafe's biggest door, and the Bulldog shows a pet whose width, not height, sets the size. The four examples cover the four shapes the answer takes, and each one is worked out in full in the worked examples section below.
One warning before you cut anything: measure twice. A pet door cut too high cannot be lowered, and a hole cut too big cannot be shrunk. Endura Flap suggests cutting a hole the size of the flap in a piece of cardboard, holding it up at the height you plan to mount the door, and watching your pet walk through it. That five-minute test catches more mistakes than any calculator can.
How it works
The calculator runs four calculations in order: the flap size you need, the matching size at each maker, the install height, and the checks that produce the warnings. Each one uses the result of the one before it, and the steps section on the page prints all four so you can check them against your own arithmetic.
Step 1: the flap size you need
The flap opening must be wider than your pet and taller than your pet's body depth, with room to move. PetSafe says to add one to two inches to both the width and the body-depth measurement. Hale says to add an inch or two to the chest width. This calculator adds the full two inches to both, which is the top of the range both makers give. Two inches is the conservative choice: a flap with two inches of clearance never binds on the shoulders or the belly, and the cost of the extra inch is nothing, because flap sizes jump in much bigger steps than an inch. A pet that just fits the chart with two inches of clearance still passes comfortably, and a pet measured with one inch of clearance would land on the same size in nearly every case.
The two numbers are the needed flap width and the needed flap height. The needed width is your pet's width plus two inches. The needed height is your pet's body depth plus two inches. The calculator shows them rounded up to the next eighth of an inch, because pet door sizes are sold in eighths and the buyer needs a flap at least the needed size. Rounding up never sells you a flap too small. The fit test itself uses the exact numbers, not the rounded display, so a pet needing 8.13 inches of width does not fit a flap 8 1/8 inches wide, even though the rounded display reads 8 1/8.
Step 2: the matching size at each maker
For each maker, the calculator picks the smallest size whose flap opening is both at least as wide as the needed width and at least as tall as the needed height. Both conditions must hold: a flap wide enough but too short does not fit, and a flap tall enough but too narrow does not fit. The smallest size that fits both is the right size. Buying one size up costs more, lets in more weather, and invites bigger animals through the door. Buying one size down leaves your pet squeezing.
The three makers' charts are different shapes. PetSafe has four dog sizes, Small through Extra Large, and its chart figures are the minimum usable opening across all its doors. Endura Flap has five sizes, Small through XX Large, and its flaps run taller than PetSafe's for the same name: an Endura Flap Large is 10 by 19 inches against PetSafe's Large at 10 1/8 by 15 3/8. Hale has eleven sizes, including tall variants that add height without width, and the calculator picks the smallest by passage area, which is the honest meaning of smallest when one size is tall and narrow and another is short and wide. The full charts are reproduced below, with the figures verified against each maker's own page on 21 November 2026.
The headline category is the PetSafe category. PetSafe is the volume brand, its chart is the one most shops stock against, and its figures are minimums, so a pet that fits the PetSafe chart figure fits that size in any PetSafe style. When no PetSafe size fits, the headline says oversize, and the table shows which makers do have a size that fits. An oversize headline does not mean no door exists: it means the pet is larger than PetSafe's biggest standard door, and the answer is usually an Endura Flap XX Large, a Hale Giant, or a Hale custom size.
Step 3: the install height
A flap of the right size mounted at the wrong height is still the wrong door. The top of the flap must sit at least one inch above the top of your pet's shoulders. Endura Flap states this in its install guide and repeats it in its measuring checklist: the top of the opening sits at or above the withers, so the pet does not have to crouch. Hale says the flaps should be at least an inch or two above the top of the pet's back. The calculator uses one inch as the minimum, which is the number both makers agree on.
The install height follows from two numbers: the minimum height of the top of the flap, which is the shoulder height plus one inch, and the height of the flap on the door you buy. The step-over, the gap between the floor and the bottom of the flap, is the difference: the minimum top height minus the flap height. If the flap is taller than the minimum top height, the step-over is zero and the door mounts at floor level, with the top of the flap sitting higher than the minimum. If the flap is shorter, the door mounts above the floor by the difference, and the step-over is that difference.
The install height is always based on a door you can actually buy. When a PetSafe size fits, it is the PetSafe size. When no PetSafe size fits but a standard door from another maker does, it is the smallest fitting standard flap, because that is the door most buyers choose. When no standard door fits at all, it is a custom door built to the minimum needed height. The results name the door the install height is based on, so you always know which flap the numbers describe.
Step 4: the checks
Three checks run on every result. The first is the step-over limit: Endura Flap says the step-over should never exceed one third of the height at the withers, and the lower the step-over, the better. A step-over over that limit strains the joints every time the pet passes through, and it gets worse as the pet ages. The calculator tests the exact step-over against exactly one third of the shoulder height, and warns when it is over, with the remedy: a taller flap lets you mount the door lower.
The second check is the PetSafe disagreement. PetSafe's size chart and PetSafe's individual model pages publish different flap sizes for the same size name. The chart gives the minimum across all doors, and the models run larger: the Freedom Aluminum Medium has an 8 1/4 by 12 1/4 inch flap against the chart minimum of 8 1/8 by 11 1/4. When your pet fits a smaller size on the model figures than on the chart figures, the calculator warns you, because the door you can actually buy may be a size smaller than the chart says.
The third check is the shape check. Most pets are deeper than they are wide, so height sets the size. A pet that is wider than it is deep, a Bulldog or a Mastiff, is sized by its width, and the matching doors are much taller than the pet needs. The calculator warns you in that case, because Hale offers custom sizes that add width without extra height, which is often the better buy for a wide, short dog.
Worked example 1: the Labrador, a straightforward Extra Large
Shoulder height 24 in, width 10 in, body depth 14 in.
- Flap width needed: 10 in + 2 in of clearance = 12 in
- Flap height needed: 14 in + 2 in of clearance = 16 in
- Smallest PetSafe size that fits both: Extra Large (13 5/8 × 23 5/8 in). The Large is 10 1/8 in wide, which is narrower than the 12 in needed, so it does not fit
- Smallest Endura Flap size that fits both: Extra Large (12 × 23 in)
- Smallest Hale size that fits both: Extra Large (14 × 19 1/2 in)
- Top of the flap must sit at least 1 in above the shoulders: 24 in + 1 in = 25 in
- With a 23 5/8 in flap (PetSafe Extra Large), mount the bottom of the opening 1.4 in above the floor
- Maximum step-over: one third of 24 in = 8 in. The 1.4 in step-over is well inside the limit
All three makers agree on the size name here, which is the exception rather than the rule: the same name covers a different flap at each maker, and the agreement is a coincidence of these particular measurements. The step-over is small because the flap is tall: a 23 5/8 in flap on a 24 in dog needs almost no lift to clear the shoulders. Note also that the PetSafe Extra Large flap is much taller than the 16 in the dog needs. The extra height is not waste: it is what keeps the step-over low.
Worked example 2: the Chihuahua, where the size names disagree
Shoulder height 8 in, width 4 in, body depth 5 in.
- Flap width needed: 4 in + 2 in of clearance = 6 in
- Flap height needed: 5 in + 2 in of clearance = 7 in
- Smallest PetSafe size that fits both: Medium (8 1/8 × 11 1/4 in). The Small is 5 1/8 in wide, which is narrower than the 6 in needed, so it does not fit
- Smallest Endura Flap size that fits both: Small (6 × 11 in)
- Smallest Hale size that fits both: Small Medium (6 1/2 × 9 1/2 in)
- Top of the flap must sit at least 1 in above the shoulders: 8 in + 1 in = 9 in
- The 11 1/4 in flap (PetSafe Medium) is taller than that, so the door mounts at floor level and the top of the flap sits 11.3 in above the floor, 3.3 in above the dog's shoulders
- Maximum step-over: one third of 8 in = 2.7 in. The door mounts at floor level, so there is no step-over at all
This is the example that shows why the calculator reports all three makers. PetSafe calls this dog a Medium, Endura Flap calls it a Small, and Hale calls it a Small Medium. All three are right by their own charts, and all three flaps fit the dog. A buyer who shops by size name alone would buy a PetSafe Small, which is 5 1/8 in wide against the 6 in the dog needs, and the dog would not fit through it. The flap dimensions in the table are the truth; the size name is a label.
Worked example 3: the Great Dane, larger than PetSafe's biggest door
Shoulder height 34 in, width 12 in, body depth 16 in.
- Flap width needed: 12 in + 2 in of clearance = 14 in
- Flap height needed: 16 in + 2 in of clearance = 18 in
- No PetSafe size fits both measurements: the largest, Extra Large, is 13 5/8 × 23 5/8 in, and 13 5/8 in is narrower than the 14 in needed
- Smallest Endura Flap size that fits both: XX Large (14 × 27 in)
- Smallest Hale size that fits both: Extra Large (14 × 19 1/2 in)
- Top of the flap must sit at least 1 in above the shoulders: 34 in + 1 in = 35 in
- With a 19 1/2 in flap (Hale Extra Large), mount the bottom of the opening 15.5 in above the floor
- Maximum step-over: one third of 34 in = 11.3 in. The 15.5 in step-over is over the limit, so the calculator warns about it
The warning matters here. A 15.5 in step-over is a jump, not a step, and a Great Dane asked to clear it several times a day will feel it in the hips. The remedy is the taller flap: the Endura Flap XX Large has a 27 in flap, and with the same 35 in top height the step-over becomes 35 minus 27, which is 8 in, inside the 11.3 in limit. That is the trade the calculator is pointing at when it warns: the smallest fitting door is not always the most comfortable door, and for a tall dog the taller flap is worth the bigger hole. The headline says oversize because no PetSafe size fits, but two standard doors do fit, and the table names them both.
Worked example 4: the Bulldog, sized by width
Shoulder height 16 in, width 12 in, body depth 10 in.
- Flap width needed: 12 in + 2 in of clearance = 14 in
- Flap height needed: 10 in + 2 in of clearance = 12 in
- No PetSafe size fits both measurements: the largest, Extra Large, is 13 5/8 in wide, and 13 5/8 in is narrower than the 14 in needed
- Smallest Endura Flap size that fits both: XX Large (14 × 27 in)
- Smallest Hale size that fits both: Extra Large (14 × 19 1/2 in)
- Top of the flap must sit at least 1 in above the shoulders: 16 in + 1 in = 17 in
- The 19 1/2 in flap (Hale Extra Large) is taller than that, so the door mounts at floor level and the top of the flap sits 19.5 in above the floor, 3.5 in above the dog's shoulders
- The dog is wider than it is deep, so width sets the size, and the calculator warns that the matching doors are much taller than the dog needs
The Bulldog is the shape that breaks the size charts. Standard pet doors are taller than they are wide, because most dogs are deeper than they are wide. A Bulldog is the opposite shape: 14 in of width needed against 12 in of height. The only standard doors wide enough are 19 1/2 and 27 in tall, far more height than a 16 in dog needs. Hale says on its sizing page that dogs like Bulldogs may need more width but not as much height, and that a custom size can add width without extra height. For a Bulldog, that is usually the better buy, and the warning says so.
PetSafe size chart
PetSafe publishes its dog door sizes in a one-page size chart, "3 Easy Steps to Select Right Size Pet Doors." The flap opening figures in that chart are the smallest amount of usable open space across all PetSafe pet doors, in PetSafe's own words. That matters: if your pet fits the chart figure for a size, your pet fits that size in any PetSafe style, plastic, aluminum, wall entry, or extreme weather. The figures below are from the chart as published on PetSafe's site, verified 21 November 2026.
| Size | Pet weight | Flap opening (width × height) |
|---|---|---|
| Small | 1-15 lb | 5 1/8 × 7 1/2 in |
| Medium | 1-40 lb | 8 1/8 × 11 1/4 in |
| Large | 1-100 lb | 10 1/8 × 15 3/8 in |
| Extra Large | 12-220 lb | 13 5/8 × 23 5/8 in |
PetSafe's weight ranges overlap heavily: a 12 lb dog sits inside Small, Medium, and Large at once. Weight is a rough guide, not a sizing rule. A 12 lb Dachshund and a 12 lb Jack Russell Terrier are different shapes and need different flaps. Measure the dog, not the scale. The weight ranges are most useful as a sanity check: if your dog weighs 90 lb and the calculator says Medium, one of your measurements is probably wrong.
PetSafe also publishes a cat door chart on the same page, with two sizes. The cat doors are wider than they are tall, the opposite shape from the dog doors, because a cat passes through low and wide.
| Size | Pet weight | Flap opening (width × height) |
|---|---|---|
| Cat Small | 1-15 lb | 5 1/2 × 5 1/8 in |
| Cat Large | 1-25 lb | 7 1/8 × 7 1/2 in |
PetSafe's individual models publish larger flap openings than the chart minimums. The Freedom Aluminum door, one of the most common door-mount models, lists a Small flap of 5 1/4 by 8 1/8 inches, a Medium of 8 1/4 by 12 1/4, a Large of 10 1/4 by 16 1/4, and an Extra Large of 13 3/4 by 23 3/4. Every one of those is bigger than the chart figure for the same size, by an eighth of an inch in width and up to an inch in height. The chart is the safe figure for sizing, because it fits every style; the model page is the figure for the door you actually buy, and it is the one the calculator checks when it warns about the PetSafe disagreement. The Freedom Aluminum frame and cut-out sizes are below. PetSafe's own warning applies to every cut-out figure on this page: always use the cutting template included in the package before cutting an opening, and never cut from a chart.
| Size | Flap opening | Outer frame | Cut-out |
|---|---|---|---|
| Small | 5 1/4 × 8 1/8 in | 7 3/4 × 11 5/8 in | 5 7/8 × 9 3/4 in |
| Medium | 8 1/4 × 12 1/4 in | 10 3/4 × 15 5/8 in | 8 7/8 × 13 3/4 in |
| Large | 10 1/4 × 16 1/4 in | 12 3/4 × 19 5/8 in | 10 7/8 × 17 7/8 in |
| Extra Large | 13 3/4 × 23 3/4 in | 16 1/4 × 27 1/8 in | 14 3/8 × 25 1/4 in |
Endura Flap size chart
Endura Flap sells five sizes, Small through XX Large, and its flaps run tall. The chart below is the single-flap size from the Endura Flap size chart on PetDoors.com, verified 21 November 2026. Double-flap doors, which add a second flap for insulation, are one inch shorter than the single-flap size shown: the double-flap Large is 10 by 18 inches, not 10 by 19. If you buy a double flap, check the height against the double-flap figure, not the single-flap figure, or a dog that fits the single flap may not fit the double.
| Size | Single flap (width × height) | Double flap (width × height) |
|---|---|---|
| Small | 6 × 11 in | 6 × 10 in |
| Medium | 8 × 15 in | 8 × 14 in |
| Large | 10 × 19 in | 10 × 18 in |
| Extra Large | 12 × 23 in | 12 × 22 in |
| XX Large | 14 × 27 in | 14 × 26 in |
Endura Flap measures differently from PetSafe. Instead of a tape on the dog's chest, Endura Flap asks you to open a door as wide as your pet needs to walk through comfortably, then measure the width of that opening. The idea is that the opening your pet chooses for itself already includes the wiggle room, so the flap needs to be at least that wide and no wider. For height, Endura Flap asks for the floor-to-tallest-point-of-back measurement, which may be the shoulders, the mid-back, or the tailbone, whichever is tallest. That height sets where the top of the flap must sit, not how tall the flap must be. The distinction matters: PetSafe's body-depth measurement sets the flap height, while Endura Flap's floor-to-back measurement sets the flap position. This calculator asks for both, because you need both to size the door and to mount it.
Endura Flap's sliding-door panel, the Thermo Panel 3e, ships with an adjustable step-over. The step-over ranges as shipped are 3 to 4 1/2 inches for Small and Medium, 3 to 6 inches for Large and Extra Large, and 3 to 7 1/2 inches for XX Large. The panel lets you move the flap up and down inside the frame to set the step-over your pet needs, which is the practical answer to the Great Dane problem in worked example 3: a taller flap and an adjustable step-over together keep the top high and the step low.
Hale Pet Door size chart
Hale Pet Door offers eleven standard sizes, more than any other major maker, including tall variants that add height without width. The table below is Hale's standard size chart from its sizing guide, verified 21 November 2026. The passage opening is the hole your pet passes through, which is the figure the calculator matches against. The rough opening is the hole you cut. Pet width and pet shoulder height are Hale's own fit ranges for each size, and they are worth checking against your measurements: if your pet's shoulder height falls outside the range for the size the calculator picks, re-measure before you buy.
| Size | Passage opening | Rough opening | Pet width | Pet shoulder height | Pet weight |
|---|---|---|---|---|---|
| Small Medium | 6 1/2 × 9 1/2 in | 8 1/2 × 11 1/2 in | Up to 4 in | 9-13 in | Small cats up to 10 lb |
| Tall Small Medium | 6 1/2 × 12 1/2 in | 8 1/2 × 14 1/2 in | 3-5 in | 12-15 in | Small, tall dogs, 12-25 lb |
| Medium | 8 1/2 × 12 1/2 in | 10 1/2 × 14 1/2 in | 6-8 in | 12-15 in | Dogs 10-35 lb |
| Tall Medium | 8 1/2 × 16 in | 10 1/2 × 18 in | 6-8 in | 15-20 in | Tall dogs 30-45 lb |
| Large | 11 × 16 in | 13 × 18 in | 8-10 in | 15-20 in | Dogs 40-55 lb |
| Tall Large | 11 × 19 1/2 in | 13 × 21 5/8 in | 8-10 in | 21-24 in | Taller dogs 50-95 lb |
| Tall Large Plus | 11 × 23 1/2 in | 13 × 25 5/8 in | 8-10 in | 25-27 in | Tall, slender dogs up to 110 lb |
| Extra Tall Large | 11 × 27 1/2 in | 13 × 29 5/8 in | 8-10 in | 24-31 in | Very tall, slender dogs up to 120 lb |
| Extra Large | 14 × 19 1/2 in | 16 × 21 5/8 in | 11-13 in | 22-24 in | Large dogs up to 120 lb |
| Extra Large Plus | 14 × 23 1/2 in | 16 × 25 5/8 in | 11-13 in | 25-27 in | Larger dogs up to 150 lb |
| Giant | 15 1/2 × 27 1/2 in | 17 5/8 × 29 5/8 in | 12-14 in | 25-31 in | Most giant breeds |
Hale's tall variants solve the problem the Great Dane example raises. A Tall Large Plus is 11 inches wide and 23 1/2 inches tall: the height of an Extra Large with the width of a Large. A tall, slender dog that needs height but not width fits a tall variant instead of jumping to a wider size it does not need. The calculator picks the Hale size by passage area, smallest first, so a tall, narrow dog lands on a tall variant rather than on a wide size with the same area. Hale's own advice for a dog between sizes is to move up to the next size, and the calculator follows that: it never rounds a pet down to a size the pet does not fit.
Hale's standard rise, the lip at the bottom of the door, is 2 inches. Panel models have a standard rise of 5 inches but can be ordered with no rise. The rise is the same thing Endura Flap calls the step-over, and the same one-third rule applies to it: a 5 inch rise on a panel door suits a dog at least 15 inches tall at the shoulders, and a shorter dog will struggle with it. If you buy a Hale panel for a short-legged dog, order it with no rise.
Where the makers disagree
The three makers disagree in three ways, and this page shows all three honestly instead of silently picking one number. The first disagreement is inside PetSafe itself. The size chart PDF lists a Medium flap of 8 1/8 by 11 1/4 inches, while the Freedom Aluminum Medium lists 8 1/4 by 12 1/4 and the Plastic Medium lists the same. The chart is the minimum usable opening across all PetSafe doors, and the models run larger. The calculator uses the chart figures for the headline category, because the chart figure fits every PetSafe style, and it computes the model figures separately so it can warn you when the door you can actually buy is a size smaller than the chart says. The table below lines the two sets of figures up.
| Size | Size chart PDF (minimum) | Freedom Aluminum model |
|---|---|---|
| Small | 5 1/8 × 7 1/2 in | 5 1/4 × 8 1/8 in |
| Medium | 8 1/8 × 11 1/4 in | 8 1/4 × 12 1/4 in |
| Large | 10 1/8 × 15 3/8 in | 10 1/4 × 16 1/4 in |
| Extra Large | 13 5/8 × 23 5/8 in | 13 3/4 × 23 3/4 in |
The gap matters most at the Medium to Large boundary. A dog needing an 11 1/2 inch tall flap does not fit the chart Medium at 11 1/4 inches, so the chart says Large. The same dog fits the Freedom Aluminum Medium at 12 1/4 inches. The calculator flags exactly this case with a warning, naming both sizes, so you can check the model page before buying the bigger door. The difference is real money and a real hole in your door.
The second disagreement is inside Endura Flap's own guidance, about how high the top of the flap must sit. The measuring guide says to add the step-over to the pet's height and mount the top of the flap at least one inch higher than that sum. The same guide's checklist says the top of the opening should sit at or above the withers, and the Thermo Panel install guide says the top of the flap should be at least one inch above the top of the shoulder. Those are different rules when the step-over is more than zero: the first counts the full step-over against a pet that steps through one foot at a time, while the second treats the shoulder height as the target. This calculator follows the checklist and install guide rule, top of flap at least one inch above the shoulders, because it is the rule Endura Flap repeats in both places and the one its install instructions actually tell you to build to. The stricter reading is stated here so you can apply it yourself if you want the extra headroom: add your step-over to the one-inch minimum and mount the top that high instead.
The third disagreement is between the makers on size names. A Large at PetSafe is 10 1/8 by 15 3/8 inches. A Large at Endura Flap is 10 by 19 inches. A Large at Hale is 11 by 16 inches. The same word covers three different holes, and the difference is not trivial: the Endura Flap Large is three and five eighths inches taller than the PetSafe Large. Weight does not fix it either. A 40 lb dog sits at the top of PetSafe's Medium, inside Hale's Tall Medium at 30 to 45 lb, and inside Hale's Large at 40 to 55 lb. The table below shows the mismatch for the Large name at all three makers. The only safe way to shop is by flap dimensions, which is what the calculator's maker table gives you.
| Maker | Large flap opening | Large weight range |
|---|---|---|
| PetSafe | 10 1/8 × 15 3/8 in | 1-100 lb |
| Endura Flap | 10 × 19 in | Not published by weight |
| Hale Pet Door | 11 × 16 in | Dogs 40-55 lb |
Step-over and install height
The step-over is the distance from the floor to the bottom of the flap opening, the lip your pet steps over to go through the door. Hale calls it the rise. It is the most overlooked number in pet door sizing, because the size charts do not mention it and a door that fits perfectly on paper can still be unusable if it sits too high. Endura Flap gives the rule plainly: in no case should the step-over exceed one third of the height at the withers, and the lower the step-over, the better. A 24 inch dog can clear an 8 inch step-over. A 12 inch dog can clear a 4 inch step-over. A 4 1/2 inch step-over suits a dog at least 13 1/2 inches tall at the withers.
The step-over and the flap height trade against each other. The top of the flap must clear the shoulders by at least an inch, so the step-over plus the flap height must reach the shoulder height plus one inch. A taller flap means a lower step-over for the same top height, which is why Endura Flap talks about high-aspect-ratio doors: a tall, narrow flap gets the step-over down to the floor for a tall dog sharing with a small one. When the calculator warns that the step-over is too high, the remedy it names is a taller flap, the next size up, which lets you mount the door lower. The Great Dane example shows the trade in numbers: the Hale Extra Large needs a 15.5 inch step-over, over the 11.3 inch limit, while the Endura Flap XX Large needs an 8 inch step-over, inside it.
Three situations need a lower step-over than the one-third rule allows. A short-legged dog, a Dachshund or a Corgi, has the shoulder height of a much smaller dog relative to its body, and the one-third limit is already generous for it. An older dog with stiff hips or arthritis may not lift its feet as high as it once did, and a step-over it cleared at three years old can defeat it at twelve. A dog recovering from surgery or injury needs the lowest step-over you can give it. In all three cases, mount the door as low as the flap height allows, and if the flap is too short to reach the shoulders from floor level, buy the taller flap rather than raising the door.
The ground outside matters too. Backyards and patios are usually a few inches lower than the floor inside the house, so the step-over your pet faces on the way back in is the indoor step-over plus the drop to the ground outside. Endura Flap flags this in its measuring guide, and it matters most for small dogs and large step-overs: a 4 inch indoor step-over with a 6 inch drop outside is a 10 inch climb on the return trip. Measure both sides before you decide the height, and put a step or a ramp outside if the drop is large.
Some installations limit the step-over from the other side. A sliding glass door panel has a fixed frame height, and the flap sits where the panel puts it: the Thermo Panel 3e adjusts across a range, but it cannot go to zero. A wall install above floorboards has a rise set by the wall construction. A door with a raised threshold or a baseboard in the way may force the flap higher than you want. In those cases the adjustable step-over panel or a taller flap is the fix, and the calculator's maximum step-over number tells you how much room you have.
Puppies, senior pets, and multi-pet homes
A puppy will grow, and a pet door sized for a puppy is a pet door you will replace. PetSafe's size chart carries the warning in capital letters: remember to allow for your pet's future growth. Hale says to size for the expected adult height and build, and Endura Flap says the same for multi-pet homes: measure the largest pet. The practical way to do it is to look up the adult size for your dog's breed, or ask your veterinarian for the expected adult shoulder height and weight, and enter the adult numbers. If you do not know the adult size, a rescue puppy of unknown breeding, for example, size for the largest plausible adult: a door one size too big is a draft, and a door one size too small is a wall. The calculator's growth note appears on every result as a reminder, because it is the most common sizing mistake after measuring the coat instead of the body.
A senior pet needs the opposite thinking. The flap size stays the same, but the step-over that was easy at five years old can become a barrier at thirteen. Arthritis, hip dysplasia, and general stiffness all reduce how high a dog lifts its feet. If your dog is already slowing down, mount the door at the lowest step-over the flap allows, even if that means buying the next size up for the taller flap. A ramp on each side of the door helps more than any flap size: a gentle slope turns a step-over into a walk-through. Our Dog Age Calculator converts your dog's age to human years, which is a useful check on whether your dog counts as senior for this purpose: a seven-year-old large dog is already in the senior range.
In a home with more than one pet, size for the widest and tallest pet, and check the smallest pet against the step-over. The flap must fit the biggest animal, but the step-over must suit the smallest. A Great Dane and a Chihuahua sharing one door need a tall flap with a low step-over, which is exactly the high-aspect-ratio case Endura Flap describes: a tall flap keeps the top above the Dane's shoulders while the bottom stays near the floor for the Chihuahua. Measure both pets, run the calculator for each, and buy the door that fits the bigger pet's flap size with a step-over the smaller pet can clear. If no single door does both, two doors at different heights are better than one door neither pet can use comfortably.
Cats need their own note. A cat passes through a flap low and wide, ducking its head and compressing its body, so a cat needs less clearance than a dog of the same measurements. PetSafe's dedicated cat doors are wider than they are tall for exactly this reason: the Cat Large is 7 1/8 inches wide and 7 1/2 inches tall. Endura Flap generally recommends its Small for cats, and still suggests measuring the cat's height. This calculator works for cats if you enter the cat's measurements: the two inches of clearance is generous for a cat, which is safe, and the maker table will show the dog-door sizes that fit. For a cat-only door, compare the result against the PetSafe cat chart above before you buy, because the dedicated cat door is usually the better fit and the cheaper buy. Our Cat Age Calculator converts your cat's age to human years if you are sizing for a kitten or a senior cat.
Features
Three measurements, one answer. Shoulder height, width, and body depth are all the calculator asks for. No weight, no breed, no guesswork. The three numbers decide the flap size and the install height between them.
Three makers, side by side. The result shows the matching size at PetSafe, Endura Flap, and Hale Pet Door, with the actual flap opening at each maker. When the size names disagree, the guidance says so and names the sizes. When PetSafe's own models disagree with its chart, the warning says so and names both sizes.
Install height, not just size. The calculator works out the step-over, the height of the top of the flap, and the maximum step-over for your pet from Endura Flap's one-third rule. The install height is always based on a door you can actually buy, and the result names that door.
Honest oversize handling. A pet larger than PetSafe's biggest door gets an oversize headline, the standard doors that do fit, and install guidance based on the smallest fitting standard flap. A pet larger than every standard door gets the custom-door guidance and the minimum dimensions to order.
Shape warnings. A pet wider than it is deep gets a warning that width sets the size and that the matching doors are much taller than needed, with the custom-size option named. A step-over over the one-third limit gets a warning with the remedy.
Full working, printed. Every step of the calculation is printed on the page: the clearance added, the flap size needed, the smallest fitting size at each maker, and the install-height arithmetic. Nothing is hidden behind the answer.
Measurement sanity checks. The calculator rejects numbers it cannot use honestly: text where a number belongs, exponent form, values outside realistic bounds, and a body depth as large as the shoulder height, which means one of the two measurements is wrong.
Use cases
Buying your first pet door. You have the dog, you have the door, and you need to know which size to order. Measure the dog, enter the three numbers, and buy by the flap dimensions in the maker table. Check the cut-out size for the model you buy against the door or wall you plan to cut: the cut-out is bigger than the flap opening, and a door panel too narrow for the frame is a common surprise.
Replacing a door your pet has outgrown. Puppies grow, and a door that fit at six months may not fit at eighteen. Re-measure the adult dog and run the calculator again. If the new size is one step up, check whether the existing hole can take the bigger frame before you order: the cut-out for the next size up is usually two inches wider and three to four inches taller.
Choosing between makers. You have narrowed it down to two brands and want to know which fits better. The maker table shows both, with the real flap dimensions, so you can see whether the PetSafe Large or the Endura Flap Large suits your dog. The install height changes with the flap height, so compare the step-over too: the taller flap usually wins for a tall dog.
Planning a wall install. A wall install has a fixed rise set by the wall construction, and the step-over cannot go below it. Run the calculator, compare the maximum step-over with the rise your wall forces on you, and pick the flap tall enough to clear the shoulders from that height. Hale's standard rise is 2 inches, and its panel models run 5 inches: check both against the one-third limit for your pet.
Sizing for two pets. Run the calculator once for each pet. Buy the door that fits the bigger pet's flap size, and check the smaller pet against the step-over. If the step-over is too high for the smaller pet, the taller flap from the next size up is the fix, not a second door, unless the size gap is so large that no single door works.
Checking a breeder or rescue recommendation. A breeder says your puppy will need a Large. Enter the expected adult measurements and check: the calculator's answer is based on the makers' charts, not on anyone's habit. If the answer disagrees with the recommendation, the measurements decide, because the charts are the authority the recommendation is supposed to follow.
Sizing the rest of the gear. The same three measurements size a crate, a carrier, and a dog house. Our Dog Crate Size Finder works out the right crate from your dog's length and height, and our Dog Exercise Calculator works out how much daily exercise your dog needs once the door is in and the dog can come and go.
Sources
Every figure on this page was re-verified against the original publisher's own page on 21 November 2026. The size charts change rarely, and the next review is due 19 May 2027.
- PetSafe, "3 Easy Steps to Select Right Size Pet Doors," size chart PDF: dog flap openings Small 5 1/8 × 7 1/2 in, Medium 8 1/8 × 11 1/4 in, Large 10 1/8 × 15 3/8 in, Extra Large 13 5/8 × 23 5/8 in; cat flap openings Small 5 1/2 × 5 1/8 in, Large 7 1/8 × 7 1/2 in; method: widest part plus one to two inches, shoulders to bottom of chest or belly plus one to two inches; the chart figures are the smallest usable open space across all PetSafe doors. PetSafe size chart PDF.
- PetSafe, "How do I measure my pet?," door dimensions document (Radio Systems Corporation): Freedom Aluminum flap openings Small 5 1/4 × 8 1/8 in, Medium 8 1/4 × 12 1/4 in, Large 10 1/4 × 16 1/4 in, Extra Large 13 3/4 × 23 3/4 in; outer frame and cut-out dimensions as tabulated above; always use the cutting template in the package before cutting.
- Endura Flap, "What Size Dog Door Do I Need? Your Guide On How to Measure a Dog For a Dog Door": width from a door opening the pet walks through; height from the floor to the tallest point of the back; top of the flap at least 1 in above the pet's height plus the step-over; step-over never more than one third of the height at the withers; top of the opening at or above the withers; cats generally take the Small. Endura Flap measuring guide.
- Endura Flap size chart, PetDoors.com: single-flap sizes Small 6 × 11 in, Medium 8 × 15 in, Large 10 × 19 in, Extra Large 12 × 23 in, XX Large 14 × 27 in; double-flap doors 1 in shorter; Thermo Panel 3e step-over ranges Small and Medium 3 to 4 1/2 in, Large and Extra Large 3 to 6 in, XX Large 3 to 7 1/2 in; top of the flap at least 1 in above the top of the pet's shoulder. Endura Flap Thermo Panel 3e.
- Hale Pet Door, "Dog Door Sizing Guide": eleven standard sizes with passage openings, rough openings, pet widths, pet shoulder heights, and pet weights as tabulated above; flaps at least an inch or two above the top of the pet's back; chest width plus an inch or two; standard rise 2 in; panel models standard rise 5 in, available with no rise; between sizes, move up; size multi-pet homes for the tallest pet. Hale Pet Door sizing guide.
Frequently asked questions
What size dog door do I need?
It depends on three measurements, not on your dog's weight. Measure the shoulder height (floor to the top of the shoulders), the width (the widest point, chest or hips), and the body depth (top of the shoulders to the bottom of the chest or belly). Add 2 inches to the width and to the body depth: the flap opening must be at least that wide and that tall. A Labrador at 24 inches at the shoulder, 10 inches wide, and 14 inches deep needs a flap at least 12 inches wide and 16 inches tall, which is an Extra Large at PetSafe, Endura Flap, and Hale. Enter your dog's three numbers above and the calculator works out the size at all three makers.
How do I measure my dog for a pet door?
Stand your dog square on level ground and take three measurements with a tape measure. First, the shoulder height: floor to the top of the shoulders, the ridge between the shoulder blades. Second, the width: the widest point, usually the chest just behind the forelegs, or the hips if they are broader. Press the tape through a long coat to the body. Third, the body depth: top of the shoulders straight down to the bottom of the chest or belly, whichever hangs lower. Endura Flap offers an alternative for width: open a door just wide enough for your dog to walk through comfortably and measure the width of that opening. Hale suggests measuring the shoulder height against your own leg if your dog will not stand still.
How much clearance should I add to my dog's measurements?
PetSafe says to add one to two inches to both the width and the body-depth measurement, and Hale says to add an inch or two to the chest width. This calculator adds the full two inches to both, which is the top of the range both makers give. Two inches is the safe choice: a flap with two inches of clearance never binds on the shoulders or the belly, and flap sizes jump in much bigger steps than an inch, so the extra inch almost never changes the size you buy. A pet that just fits the chart with two inches of clearance still passes comfortably.
Why do PetSafe, Endura Flap, and Hale give different sizes for the same dog?
Because the same size name covers a different flap opening at each maker. A Large at PetSafe is 10 1/8 by 15 3/8 inches, a Large at Endura Flap is 10 by 19 inches, and a Large at Hale is 11 by 16 inches. The Endura Flap Large is three and five eighths inches taller than the PetSafe Large. Weight does not fix it either: a 40 lb dog sits at the top of PetSafe's Medium, inside Hale's Tall Medium at 30 to 45 lb, and inside Hale's Large at 40 to 55 lb. Buy by the flap dimensions, not by the size name, and check the maker table this calculator prints before you order.
How high should I mount a pet door?
The top of the flap must sit at least 1 inch above the top of your pet's shoulders, and the step-over, the gap between the floor and the bottom of the flap, must not exceed one third of the shoulder height. Endura Flap states both rules: the top of the flap at least 1 inch above the shoulder, and the step-over never more than one third of the height at the withers. For a 24 inch dog, the top of the flap sits at least 25 inches above the floor and the step-over stays at or under 8 inches. If the step-over comes out too high, a taller flap lets you mount the door lower. The calculator works out the step-over, the top height, and the maximum step-over for your pet.
What if my dog is between two sizes?
Size up. Hale's sizing guide says that when a dog falls between sizes, you should usually move up to the next size if shoulder height, body width, or jumping comfort are close to the larger opening. A door one size too big is a draft; a door one size too small is a wall your dog cannot get through. One exception is worth checking: PetSafe's individual models have larger flaps than its size chart minimums, so a dog that falls between sizes on the chart may fit the smaller size in the Freedom Aluminum model, whose Medium flap is 8 1/4 by 12 1/4 inches against the chart minimum of 8 1/8 by 11 1/4. This calculator warns you when that is the case.
What size pet door does a cat need?
Measure the cat the same way: shoulder height, width, and body depth, then add 2 inches to the width and body depth. Most cats fit a small dog door, but the dedicated cat doors fit better because they are wider than they are tall: PetSafe's Cat Small is 5 1/2 by 5 1/8 inches for cats up to 15 lb, and the Cat Large is 7 1/8 by 7 1/2 inches for cats up to 25 lb. Endura Flap generally recommends its Small for cats. Keep the step-over low for a cat, 1 to 3 inches, and mount the door at floor level when the flap height allows it. Enter the cat's measurements above and compare the result against the PetSafe cat chart before you buy.
Should I size a pet door for a puppy?
No. Size for the expected adult measurements. PetSafe's size chart warns in capital letters to allow for your pet's future growth, Hale says to size for the expected adult height and build, and Endura Flap says to measure the largest pet in a multi-pet home. A door sized for a puppy is a door you will replace within a year. Look up the adult size for your dog's breed, or ask your veterinarian for the expected adult shoulder height, and enter the adult numbers. If you do not know the adult size, size for the largest plausible adult: the extra size costs little and the door lasts the dog's life.