Skip to content

Sleeping Pad R-Value Finder

The coldest temperature you expect overnight. -60 to 110 degrees F. Use the forecast low for the coldest night of the trip.

Minimums are for a warm sleeper on dry ground. Cold sleepers add 1 to the table figure. Average sleepers add 0.5.

Snow and frozen ground add 1. Rock adds 0.5. Dry dirt, grass, or sand is the baseline, with no adjustment.

R-values add, so two pads stacked give the sum of their R-values. A foam pad under an air pad is the usual winter stack.

The ASTM R-value printed in your pad's specs, such as 4.5. Leave it blank to get the minimum to shop for instead.

Your minimum R-value

How the minimum was worked out

The working, step by step

      This tool estimates the minimum sleeping pad R-value for the night you describe, for general planning only. It is not a guarantee of warmth: your metabolism, your sleeping bag, your tent, the ground, and the weather all change the real night. In cold conditions, carry more insulation than the minimum, tell someone your plans, and know the signs of hypothermia before you go out.
      What R-value sleeping pad do I need? The Exped and SectionHiker table gives the minimum for a warm sleeper on dry ground: R 1 at 50 degrees F, R 2 at 30 degrees, R 3 at 25 degrees, R 4 at 10 degrees, R 5 at 0 degrees, R 6 at -15 degrees, R 7 at -25 degrees, and R 8 at -40 degrees. Cold sleepers add 1, and snow or frozen ground adds 1. A 0-degree night on snow needs R 6.5 for an average sleeper, which a foam pad rated R 2 under an air pad rated R 4.5 reaches exactly, because R-values add. Enter your overnight low, sleeper type, and ground above for your minimum, plus a verdict on any pad you already own.

      Last reviewed: 21 November 2026. Reviewed every 180 days; next review due 19 May 2027.

      How to use the Sleeping Pad R-Value Finder

      Enter the coldest overnight low you expect on the trip, in degrees Fahrenheit, then tell the tool how you sleep and what you will be sleeping on. The finder reads your minimum R-value off the Exped and SectionHiker temperature table, adjusts it for a cold sleeper and for rock or snow, and tells you the lowest R-value that will keep you warm. If you already own a pad, enter its R-value and the tool checks it against the minimum, tells you how much margin you have or how far short you fall, and works out the coldest night that pad can handle.

      Start with the forecast low for the coldest night of the trip, not the average night. A forecast is a guess, and mountain valleys run colder than the town the forecast was written for, so use the coldest plausible low rather than the mildest. If the forecast says 25 degrees with a chance of frost, enter 20. The table steps up to the colder row between listed temperatures, so a low of 20 degrees takes the R-value of the 10-degree row, and that caution is deliberate: a pad that is slightly too warm is a comfort problem, while a pad that is too cold can leave you shivering from midnight to dawn.

      Next, pick how you sleep. The table minimums are for a warm sleeper on dry ground. If you usually wake up cold in a bag that should be warm enough, you are a cold sleeper, and the tool adds 1 to the table figure, the hedge SectionHiker recommends for cold sleepers. Average sleepers add 0.5, which is this tool's midpoint between the warm and cold figures. Then pick the ground: dry dirt, grass, or sand is the baseline with no adjustment, rock adds 0.5 because stone draws heat away faster than soil, and snow or frozen ground adds 1 because it draws heat away fastest of all.

      If you are shopping for a pad, leave the pad fields blank and the tool gives you the minimum to shop for, plus the REI warmth band it falls in. If you already own a pad, enter its ASTM R-value from the specs and the tool gives you a verdict: covered, with the margin stated, or short, with the shortfall stated. Switch to two-pad mode to check a stack, or to size the second pad: enter the pad you own, leave the second pad blank, and the tool tells you the smallest second-pad R-value that reaches the minimum. R-values add, so a foam pad rated R 2 under an air pad rated R 4.5 gives you R 6.5.

      The result also shows the coldest night your pad can handle, worked out by interpolating between the table rows. That figure is for a warm sleeper on dry ground, so treat it as the optimistic end of the range: if you sleep cold or you are camping on snow, your real limit is warmer than the printed figure. The worked examples further down this page run through a summer night, a fall trip, a winter snow camp, and an expedition night, with every number shown, so you can check the tool's reasoning against your own trip.

      What sleeping pad R-value means

      R-value measures thermal resistance: how strongly a material resists heat flowing through it. On a sleeping pad, the R-value tells you how well the pad slows the flow of heat from your body into the ground beneath you. The higher the number, the more insulation sits between you and the cold earth. A pad rated R 1 slows heat loss a little. A pad rated R 5 slows it a lot. The scale is roughly proportional in the way that matters to a camper: REI notes that a pad rated R 2 is twice as warm as a pad rated R 1, because it lets half as much heat through.

      The ground is the part of the sleep system most campers underestimate. A sleeping bag insulates you from the air, but the insulation underneath you is compressed flat by your body weight, so it does almost nothing. The pad is the only insulation between you and ground that can be many degrees colder than the air, and ground that stays cold long after the air warms up. On a 40-degree night in spring, the soil may still hold winter cold, and an uninsulated pad will drain heat out of you all night even inside a bag rated far below freezing. That is why experienced backpackers treat the pad as half the sleep system, not an accessory: the bag handles the air, the pad handles the ground, and either one failing leaves you cold.

      R-value is a single number, which makes it easy to compare pads, but it is not a temperature rating, and no single number can capture everything that decides whether you sleep warm. Your metabolism, what you ate for dinner, how tired you are, the humidity, the wind moving under a tarp, and the temperature of the ground itself all shift the real answer. The table this tool uses is a planning guide built from a manufacturer's recommendations, not a laboratory guarantee. It answers the question every camper actually asks, which is what is the coldest night this pad can handle, with a number that is honest about being a minimum for a warm sleeper on dry ground.

      Before 2020, R-values were barely comparable between brands at all. Every manufacturer measured insulation its own way, some tested and some estimated, and a shopper comparing two pads had no way to know whether the numbers meant the same thing. The ASTM F3340-18 standard changed that by defining one test method every manufacturer could use, and the major brands adopted it from 2020 onward. An R-value measured to ASTM F3340 can be compared across brands with confidence, which is why this tool asks for the ASTM figure and why the buying advice below tells you to check for the standard on the spec sheet. Pads that carry no ASTM rating may still be fine for warm weather, but their numbers cannot be trusted against the table.

      The R-value temperature table

      The table below is the Exped recommendation as published by SectionHiker, and it is the table this tool runs on. Each row gives the minimum R-value for a warm sleeper on dry ground at that air temperature. The air temperatures are the ones you can read off a weather forecast, which is the point: you do not need a ground thermometer, you need the overnight low.

      Overnight lowOvernight lowMinimum R-valueTypical use
      50 degrees F10 degrees CR 1Warm summer nights
      30 degrees F-1 degrees CR 2Spring and fall
      25 degrees F-4 degrees CR 3Cold three-season nights
      10 degrees F-12 degrees CR 4Early winter
      0 degrees F-18 degrees CR 5Winter camping
      -15 degrees F-26 degrees CR 6Hard frost
      -25 degrees F-32 degrees CR 7Severe frost
      -40 degrees F-40 degrees CR 8Extreme conditions

      Read the table as minimums, not targets. At 30 degrees, R 2 is the least insulation a warm sleeper needs on dry ground, and most campers will be happier with a little more. The steps between rows are uneven because the table was built from field experience rather than a formula: the jump from R 1 to R 2 covers 20 degrees of temperature, while the jump from R 2 to R 3 covers only 5 degrees, because the coldest part of the three-season range is where ground cold starts to bite. Below freezing the steps settle into a steadier pattern of 10 to 15 degrees per R-value, which is why the tool extrapolates past the coldest row at 15 degrees per R-value, the last table step.

      Between rows, this tool steps up to the colder row. A low of 20 degrees sits between the 25-degree row (R 3) and the 10-degree row (R 4), so the tool gives R 4. That is the conservative reading of a minimums table, and it is the reading that keeps you warm when the forecast is a few degrees optimistic. The opposite direction, interpolating down toward the warmer row, would hand you a pad that meets the table at the forecast temperature and fails it the moment the night runs three degrees colder than expected. The only place the tool interpolates is the coldest-night figure for a pad you already own, where a smooth estimate between rows is the honest answer to the question of how cold that pad can go.

      Above 50 degrees the table has no rows, because warmer nights do not need more insulation than R 1, and the tool holds the base at R 1 for any low above 50 degrees. Below -40 degrees the table ends, and the tool extrapolates: -50 degrees gives R 9, and -60 degrees gives R 10. Treat those extrapolated figures as planning numbers for expedition conditions, not as measured ratings, and remember that at those temperatures the pad is one part of a winter system that also needs a bag rated for the cold, a tent or snow shelter that holds heat, and the experience to use them.

      What R-value do I need?

      The short answer depends on three things: how cold the night will be, how warm you sleep, and what is under the pad. The table below runs the tool's arithmetic for the eight table temperatures, for three kinds of sleeper: a warm sleeper on dry dirt, a cold sleeper on dry dirt, and a cold sleeper on snow. Find your overnight low, read across to your kind of sleeper, and you have your minimum. The full tool does the same arithmetic for any temperature, including temperatures between the rows, and checks a pad you already own against the result.

      Overnight lowWarm sleeper, dry groundCold sleeper, dry groundCold sleeper, snow
      50 degrees FR 1R 2R 3
      30 degrees FR 2R 3R 4
      25 degrees FR 3R 4R 5
      10 degrees FR 4R 5R 6
      0 degrees FR 5R 6R 7
      -15 degrees FR 6R 7R 8
      -25 degrees FR 7R 8R 9
      -40 degrees FR 8R 9R 10

      Two things stand out from that table. First, the sleeper and the ground together can add 2 full points to the minimum, which is the difference between a three-season pad and a winter pad. A cold sleeper on snow at 0 degrees needs R 7, where a warm sleeper on dry dirt needs R 5 at the same temperature. Second, the numbers climb fast once the temperature drops below freezing: every 10 to 15 degrees of extra cold costs another point of R-value, and the pads that deliver those points get heavier and more expensive. That is why winter campers stack pads instead of buying one extreme pad, and why the stacking section below matters more than it looks.

      If you camp in only one season, buy for the coldest night of that season rather than the average night. A three-season backpacker whose coldest nights reach 25 degrees needs R 3 as a warm sleeper and R 4 as a cold sleeper, so a pad rated R 4 to R 4.5 covers the whole three-season range with margin. A summer-only camper who never sees a night below 50 degrees can carry the lightest pad on the shelf. A winter camper who expects 0-degree nights on snow needs R 6 to R 7, which usually means a stack or a dedicated winter pad. When the answer falls between two pads you own, take the warmer one: the weight penalty of half a point of R-value is small, and the comfort penalty of half a point too little is a night awake.

      Warm sleepers, cold sleepers, and the plus-1 rule

      The single biggest adjustment in this tool is the sleeper, and it is the one most campers get wrong about themselves. The table minimums are for a warm sleeper on dry ground. SectionHiker puts it plainly: women need higher R-value pads because they have lower body mass than men, and an additional R-value of 1 is usually a good hedge for women and other cold sleepers. That plus-1 rule is the most quoted piece of sleeping pad advice in print, and this tool applies it exactly as stated: pick cold sleeper, add 1.

      How do you know which kind of sleeper you are? The test is your own history, not a questionnaire. If you have spent nights shivering in a sleeping bag rated well below the overnight temperature, while your tent partner slept soundly in the same conditions, you sleep cold. If you regularly wake up warm and kick the bag off your legs, you sleep warm. If you have never paid attention, assume you are average: the tool adds 0.5 for an average sleeper, which splits the difference between the warm sleeper's table figure and the cold sleeper's plus-1. That midpoint is this tool's own allowance, not a published figure, and it is labeled as such in the tool's notes. The published figures are the warm sleeper's table value and the cold sleeper's plus-1; the average sleeper sits between them.

      Body size matters for the same reason SectionHiker names: a smaller body has less mass generating heat and more surface area losing it relative to that mass. Age matters too, since metabolism slows with age, and so does fatigue: a hard day on the trail leaves you colder at night than a rest day at the same temperature, because your body has less energy to spare for staying warm. Food matters as well. A hot, calorie-rich dinner before bed is worth real warmth, while going to bed hungry on a cold night is a reliable way to wake up shivering at 2 a.m. None of these factors change the tool's arithmetic, but they decide whether you should read your result as a firm minimum or as a starting point to round up from.

      One practical rule covers the uncertainty: if you are between two pads, take the warmer one, and if you are unsure whether you sleep cold, assume you do. The cost of an extra point of R-value is a few ounces and a few dollars. The cost of a point too little is a night you do not sleep, and a second day on the trail run on no rest. Cold sleepers who camp with a partner sometimes solve the problem by sharing warmth, but the pad does not care about the partner: each sleeper needs their own insulation from the ground, and a double pad is rated as one surface, not as two warm sleepers.

      Ground type: dirt, rock, and snow

      What you sleep on matters as much as the air temperature, because the pad's job is to insulate you from the ground, and different ground steals heat at different rates. Dry dirt, grass, and sand are the baseline: they are poor conductors, they hold some air in their structure, and they cool slowly. This tool applies no adjustment for them, which is what the table assumes. Rock and concrete are a step colder. Stone is a good conductor of heat, it holds the cold of the night and of the season, and it stays cool long after the sun sets. A granite slab that felt warm at sunset can be cold by midnight, and it will pull heat out of a sleeper steadily all night. The tool adds 0.5 for rock, which is this tool's planning allowance rather than a published figure.

      Snow and frozen ground are the coldest case, and the tool adds a full point for them. Snow looks soft and insulating, and a deep snowpack does insulate the ground below it, but the surface you lie on is at or near freezing, and the top layer of snow melts under your body heat and refreezes, which draws heat away efficiently. Frozen soil is worse still: it is a solid block at or below freezing with the thermal conductivity of ice. Winter campers know this from experience, which is why snow camping advice always pairs a high R-value with a foam pad underneath. REI's winter camping guidance recommends an insulated, high R-value air pad for snowy conditions, with a closed-cell foam pad underneath it: the foam adds insulation, protects the air pad from punctures, and forms a barrier against the moisture that collects under a pad on cold ground. The tool repeats that advice as a warning whenever you pick snow.

      Ground temperature also lags the seasons, a point REI's experts make explicitly: camping in spring, when the earth has not warmed up yet, calls for a warmer sleeping pad than the one you would need in fall, when warmer ground temperatures do not draw away as much body heat. The same 30-degree night in April and in October is not the same night for your pad, because the April ground is still holding winter cold and the October ground is still holding summer warmth. If your trip is early in the season, on ground that has only just thawed, round your result up. The same applies to high altitude, where the ground is colder than the air temperature alone suggests, and to damp ground, where water in the soil conducts heat far better than dry soil does. A wet meadow in spring is closer to rock than to dry dirt in what it does to your warmth.

      Where you pitch the tent is part of the same decision. A flat patch of dry grass or pine duff is warmer ground than a flat rock slab or a patch of bare, damp earth, even at the same air temperature. Pine needles, dry leaves, and duff add a thin layer of dead air under the tent floor, which is free insulation. Snow campers sometimes dig down to a flat snow surface and accept the cold, because a level snow platform beats a sloped patch of frozen dirt. None of this replaces the pad, but it explains why two campers with the same pad and the same forecast can have different nights: the ground under them was not the same ground.

      Stacking two pads: R-values add

      The most useful fact in sleeping pad shopping is that R-values are additive. Stack two pads and the combined insulation is the sum of their R-values. A foam pad rated R 2 under an air pad rated R 4.5 gives you R 6.5, which is winter territory reached with two ordinary pads instead of one extreme one. SectionHiker states the rule plainly, REI states it too, and this tool's stacking mode is built on it: enter both pads and the tool adds them, compares the total against your minimum, and tells you the margin or the shortfall.

      Stacking is how most winter campers reach the high R-values the table demands below freezing. A single pad rated R 7 or R 8 is a specialized, heavy, expensive piece of gear, while a foam pad rated R 2 costs little, weighs about 14 ounces, cannot puncture, and doubles as a sit pad at camp and a splint in a first aid kit. Carrying that foam pad under a good three-season air pad turns a summer and fall kit into a winter kit for the price of the foam pad and the bulk of strapping it to the outside of the pack. The foam pad also protects the air pad from punctures on frozen ground and from the sharp ice that forms under a tent in winter, which is why REI recommends the combination for winter camping rather than a single high R-value pad alone.

      The order matters: foam on the bottom, air pad on top. The foam pad takes the abuse of the ground, blocks moisture from below, and insulates the air pad from the coldest surface, while the air pad on top gives you the comfort and the fine insulation next to your body. Reversed, the air pad sits on the cold ground and the foam pad on top adds little comfort, and the stack still adds up to the same R-value on paper but performs worse in practice because the air pad loses pressure as it cools. The tool does not ask which pad is on top, because the arithmetic is the same either way, but the setup advice is worth following.

      Two warnings apply to stacking. First, the two pads can slide against each other during the night, especially if the top pad is a smooth nylon air pad on a smooth foam surface. A pad strap, a fitted sheet, or a tent floor with some grip keeps the stack together. Second, a stack is bulkier than a single pad, and the foam pad strapped to the outside of a pack catches branches and weather. Our Backpack Capacity Planner sizes a pack for the load including a foam pad carried outside, and our Backpack Base Weight Calculator counts the pad toward base weight, so you can see what the stack costs in carried weight before you decide it is worth it.

      Stacking also rescues a pad you already own. If the tool tells you your R 4.2 air pad falls R 0.3 short for a 20-degree night, a foam pad rated R 2 under it gives you R 6.2, which covers the night with R 1.7 to spare and handles colder nights besides. If the tool tells you the same pad falls R 2.3 short for a 0-degree night on snow, the sizing mode tells you the second pad needs R 2.3 or higher, and any standard foam pad rated R 2 is close but not quite enough, so you would look for a thicker foam pad or accept a small shortfall on a night you expect to be mild. The tool sizes the second pad to the next tenth, so the number it gives is the smallest second pad that reaches the minimum exactly.

      REI's R-value bands

      REI groups pads into four warmth bands, and the tool shows which band your minimum falls in as a cross-check on the table. The bands are broad, and they run about half a point warmer than the Exped and SectionHiker table at the cold end, which is worth knowing rather than worrying about: the two guides were written for different purposes, and the difference is a margin, not a contradiction.

      REI bandR-value rangeExpected nighttime lowSleeping bag rating
      Warm weatherUnder 250 degrees F30 degrees F or lower
      Cool weather2 to 3.932 degrees F20 degrees F or lower
      Cold weather4 to 5.420 degrees F15 degrees F or lower
      Extremely cold weather5.5 and up0 degrees F0 degrees F or lower

      Compare the two guides at 0 degrees. The Exped and SectionHiker table gives R 5 as the minimum for a warm sleeper on dry ground. REI puts a 0-degree night in the 5.5 and up band. The half-point gap is the difference between a minimum and a band boundary: REI's bands are drawn so that the whole band covers the stated conditions for most sleepers, while the table's minimum is the floor for a warm sleeper. A warm sleeper on dry ground at 0 degrees is fine on R 5 by the table, and a cold sleeper at the same temperature needs R 6, which sits inside REI's 5.5 and up band. The two guides agree once the sleeper is taken into account, which is why the tool applies the sleeper adjustment before it reports the band.

      At 20 degrees the two guides line up neatly. The table steps a 20-degree low up to the 10-degree row, giving R 4, and REI's cold weather band for a 20-degree low starts at R 4. At 32 degrees the table gives R 2, which is the bottom of REI's cool weather band. The agreement is closest in the middle of the range and loosest at the extremes, which is the pattern you would expect from two guides built from field experience rather than from a single formula. When the guides disagree, the tool follows the table, because the table is the finer-grained of the two, and it reports the REI band alongside so you can see the cross-check.

      The bag ratings in the table above are REI's pairings, and they show the same half-point caution: REI pairs a 0-degree night with a bag rated 0 degrees or lower and a pad of 5.5 and up, which is a system with margin built in. The sleeping bag section below goes into the pairing in more detail, including the important fact that bag ratings themselves assume a pad of a stated R-value, so the pad and the bag cannot be chosen independently.

      Matching your pad to your sleeping bag

      A sleeping pad and a sleeping bag form one system, and the two ratings assume each other. REI states that sleeping bag temperature ratings assume use with a pad that has an R-value of 4, and SectionHiker notes that EN sleeping bag temperature ratings are predicated on using a sleeping pad with an R-value of 5 or higher. The two figures differ because they describe different rating systems, but the lesson is the same: a bag rated to 0 degrees will not keep you warm at 0 degrees if the pad underneath you is a thin summer pad, because the rating was measured with a proper pad in place. The international bag test itself lays the bag on a mat rated 0.85 square meter kelvin per watt, which converts to about R 4.8, sitting between the two figures and confirming that both are roundings of the same test condition.

      This is the most common reason campers report that their bag does not live up to its rating. SectionHiker makes the point directly: if you find yourself sleeping cold in temperatures where you would expect your sleeping bag to keep you warm, it may be because your sleeping pad has an R-value less than 5. The bag is doing its job against the air. The heat is leaving downward, through a pad that cannot hold it, and no amount of extra loft on top will fix a leak underneath. The fix is a warmer pad, not a warmer bag, and it is usually the cheaper fix of the two.

      The practical rule is to match the pad to the bag's rating, or to the night, whichever is colder. If your bag is rated to 20 degrees and the night will reach 20 degrees, the pad needs to cover a 20-degree night, which is R 4 for a warm sleeper on dry ground and R 5 for a cold sleeper. If your bag is rated to 0 degrees but the night will only reach 30 degrees, the pad needs to cover the 30-degree night, not the bag's rating, because the ground will only be as cold as the night makes it. The tool works from the overnight low, which is the right input for the pad, and the bag rating enters only as a check: if the tool's minimum is far above the R-value your bag's rating assumes, the bag rating is not the limiting factor, and the pad is.

      Quilts deserve a note here, because they have no insulation underneath at all and rely entirely on the pad. A quilt sleeper's pad is doing the whole job below the body, with no compressed bag insulation contributing even a little, so quilt users should read the table strictly and round up rather than down. The same applies to hammock campers who use a pad inside the hammock instead of an underquilt: the pad is the insulation, the air moves under the hammock, and the effective cold is worse than the forecast suggests. Hammock users generally do better with an underquilt, but if a pad is what you have, size it for a night colder than the forecast.

      Clothing is the third part of the sleep system, and it can rescue a marginal night. Sleeping in a warm base layer, warm socks, and a hat adds real insulation on top, and a down jacket draped over your feet warms the end of the bag that usually gets cold first. But clothing cannot fix a pad that is far too thin, because the heat loss is downward through the pad, and a jacket on top does not plug a leak below. Treat clothing as margin on a night that is close to your pad's limit, not as a substitute for the R-value the night needs.

      Types of sleeping pads and their R-values

      Pads come in three types, and each type has a characteristic R-value range, a characteristic weight, and a characteristic failure mode. Knowing the ranges helps you read the tool's result as a shopping list: if the tool says R 2, a foam pad will do; if it says R 6.5, you are looking at an insulated air pad or a stack.

      Closed-cell foam pads are the simplest type: dense foam filled with tiny closed air cells, rolled up or folded in an accordion. REI notes that most have an R-value around 2, and they are light, inexpensive, durable, and consistent in all conditions. They cannot puncture, they cannot deflate, they work as sit pads at camp, and they work underneath other pads to add insulation and protection. Their drawbacks are comfort, since foam is stiff and firm, and bulk, since a foam pad does not pack down. Published examples of foam pad R-values include the Therm-a-Rest Z Lite Sol at R 2.0, the NEMO Switchback at R 2.0, and the Exped FlexMat Plus at R 2.2. Those figures are the manufacturers' published specs, given here as examples of what foam pads measure, not as recommendations for any particular pad.

      Self-inflating pads combine open-cell foam and air: opening the valve lets air in and the foam expands. They offer a broad range of warmth, from cool-weather pads around R 2 to cold-weather pads above R 5, with excellent insulation and comfort from the foam's cushioning. They are heavier and bulkier than air pads when packed, and they can be punctured, though field repair is usually easy. Self-inflating pads are a good choice for car camping, where weight and packed size matter less, and for campers who want the most comfortable sleep. REI lists the Big Agnes Divide Insulated and the Sea to Summit Camp Self-Inflating, both rated R 4.2, as examples in the cold weather band, and the REI Co-op Trailmade Self-Inflating at R 5.5 as an extreme cold example.

      Insulated air pads are the lightest and most packable type, and they cover the widest R-value range, from uninsulated summer pads near R 1 to winter pads above R 7. They pack down small, weigh little, and let you adjust firmness by adding or releasing air. Their drawbacks are price, which rises as weight falls, and vulnerability to punctures, which is why winter campers put a foam pad underneath. Published examples include the Therm-a-Rest NeoAir XLite NXT at R 4.5 and 13 ounces, the most common three-season backpacking pad, and the Therm-a-Rest NeoAir XTherm NXT at R 7.3 and 15.5 ounces, a winter pad that carries its warmth at a weight most three-season pads would envy. Again, these are published specs offered as examples of what air pads measure, not recommendations.

      Thickness is not warmth, and the two are easy to confuse when shopping. A thick uninsulated air pad can feel luxurious to lie on and still leave you cold, because still air inside a pad circulates and carries heat from your body to the ground unless the pad's construction stops it. Insulated air pads use reflective films, baffles, and fill to break up that circulation, which is what earns the R-value. A 3-inch pad rated R 1.5 is a summer pad no matter how comfortable it feels in the store, and a 2-inch pad rated R 5 is a winter pad no matter how thin it looks. Read the R-value, not the thickness, and check that the R-value is an ASTM figure before you compare it against the table.

      Size matters too, and it interacts with the tent. Most pads measure 20 inches across and 72 inches long, but wider pads at 25 or 30 inches suit restless sleepers and larger campers, and long pads at 78 inches keep tall campers' feet insulated. SectionHiker notes that if a pad model has multiple sizes, they all have the same R-value unless specified otherwise, so going wide does not cost you warmth. It does cost you tent space, so check the tent floor against the pads you plan to use: our Tent Size Finder works out how many pads fit a tent floor. Weight and packed size matter most to backpackers, and REI's advice is to pick two qualities to prioritize, because no pad is best at everything: warmth, weight, packability, comfort, durability, and price all trade against each other.

      Worked examples

      The examples below run the tool's arithmetic end to end, so you can check the reasoning against your own trip. Every figure is the tool's output for the stated inputs.

      Summer night: 55 degrees, warm sleeper, dry dirt

      The low of 55 degrees is warmer than the warmest table row, so the base minimum stays at the table floor of R 1. A warm sleeper adds nothing, dry dirt adds nothing, and the required minimum is R 1, in REI's warm weather band. Any pad rated R 1 or higher covers the night for warmth, so the choice turns on comfort, weight, and price rather than insulation. A foam pad rated R 2 is more than enough, and an uninsulated air pad near R 1 is fine too. The tool warns that the published table starts at 50 degrees, which is a reminder that the answer is a floor, not a target: on a warm night, pick the pad you will sleep best on.

      Fall trip: 30 degrees, cold sleeper, dry dirt, R 3 pad

      The low of 30 degrees is a table row, so the base minimum is R 2. A cold sleeper adds 1, dry dirt adds nothing, and the required minimum is R 3, in REI's cool weather band. The camper's R 3 pad exactly meets the minimum, with nothing to spare, and the tool says so plainly: the pad meets the requirement exactly, and the coldest night it handles is 25 degrees, which is the table row for R 3. An exact meet is a pass, but it leaves no margin for a forecast that runs cold, so this camper should pack an extra layer or accept that a 25-degree night is the pad's limit.

      Winter snow camp: 0 degrees, average sleeper, snow, foam plus air pad

      The low of 0 degrees is a table row, so the base minimum is R 5. An average sleeper adds 0.5, snow adds 1, and the required minimum is R 6.5, in REI's extremely cold weather band. The camper's stack is an air pad rated R 4.5 over a foam pad rated R 2, which adds up to R 6.5 and exactly meets the minimum. The coldest night the stack handles is -20 degrees, interpolated between the -15 degree row for R 6 and the -25 degree row for R 7. The tool also warns about snow: put the foam pad under the air pad, where it adds insulation, protects against punctures, and blocks the moisture that collects under a pad on cold ground.

      Expedition night: -25 degrees, cold sleeper, snow

      The low of -25 degrees is a table row, so the base minimum is R 7. A cold sleeper adds 1, snow adds 1, and the required minimum is R 9, in REI's extremely cold weather band. No single common pad reaches R 9, so the answer is a stack: a winter air pad rated R 7.3 over a foam pad rated R 2 gives R 9.3, which covers the night with R 0.3 to spare. The tool warns that R 9 is expedition territory, where pads this warm are heavy and costly and most winter campers reach the figure by stacking. It also warns, for any night past -40 degrees, that the table ends and the figure is extrapolated, though -25 degrees is inside the published table and needs no extrapolation.

      Shortfall: 20 degrees, average sleeper, dry dirt, R 4.2 pad

      The low of 20 degrees sits between the 25-degree row (R 3) and the 10-degree row (R 4), so the tool steps up to the colder row and the base minimum is R 4. An average sleeper adds 0.5, dry dirt adds nothing, and the required minimum is R 4.5, in REI's cold weather band. The camper's R 4.2 pad falls R 0.3 short. The coldest night the pad handles is 8 degrees, interpolated between the 10-degree row for R 4 and the 0-degree row for R 5, which is warmer than the 20-degree night in question, so the shortfall is small and the pad is close. A foam pad rated R 2 under it would give R 6.2, covering the night with R 1.7 to spare. Alternatively, the camper could accept the small shortfall on a night forecast to stay near 20 degrees, and pack the foam pad only if the forecast turns colder.

      Sizing a second pad: 0 degrees, average sleeper, snow, R 4.2 pad

      The same R 4.2 pad on a 0-degree night on snow faces a required minimum of R 6.5: base R 5, plus 0.5 for an average sleeper, plus 1 for snow. The pad falls R 2.3 short, so the stacking mode sizes the second pad at R 2.3 or higher, rounded up to the next tenth. A standard foam pad rated R 2 is just short of that figure, which is useful to know before the trip rather than during it: the camper needs a thicker foam pad, or a second air pad, or a warmer single pad. The arithmetic is the point of the sizing mode. Guessing at the second pad risks carrying a pad that does not close the gap, and the tool removes the guesswork.

      How R-value is measured: the ASTM F3340 standard

      Before the standard, R-values were a mess. SectionHiker describes the problem plainly: before ASTM F3340-18 was formalized, every company had a different way of computing R-values, making comparisons impossible, and you had no real way of knowing whether pads had ever been tested, whether the published R-values were estimated, or just made up. The standard was spearheaded by REI, Exped, Therm-a-Rest, Sea to Summit, NEMO, Big Agnes, and Klymit, and it specifies one test methodology that every manufacturer can use, so that a published R-value means the same thing regardless of whose pad it is printed on.

      The test itself uses a guarded hot plate: the pad is held under a constant compressive force between a heated plate and a cold plate, and the apparatus measures the steady flow of heat down through the pad's thickness. The R-value is the thermal resistance that flow implies. The method is a laboratory measurement of the pad alone, in controlled conditions, which is both its strength and its limit. It makes pads comparable, which is what a shopper needs, but it does not measure how warm you will feel on a particular night, because it cannot see your metabolism, your bag, your tent, or the ground. The standard says so itself: the measured value will not always match real-world performance, because in a tent heat also escapes at the pad's edges, through surfaces you are not covering, and as compression and posture change through the night. The table that turns R-values into temperatures is a separate step, built from manufacturer recommendations and field experience, and it carries the uncertainty of any such guide.

      The standard has been in use by most major manufacturers since early 2020, and the current edition is ASTM F3340-22, a revision of the 2018 edition the table is based on. The revision did not change the meaning of the numbers in a way that affects this tool: an R 5 pad measured under either edition is an R 5 pad for the purposes of the table. What matters for shopping is that the R-value on the spec sheet is an ASTM figure at all. SectionHiker warns that many companies still publish R-values that are not measured using the standard, including most of the low-cost brands sold through online marketplaces, and advises sticking to warm-weather use for such pads and choosing an ASTM-rated pad for anything below freezing, so you know exactly what you are getting.

      One detail worth knowing: the R-value on the spec sheet is for the pad as sold, and it assumes the pad is used as designed. An air pad that is underinflated sags and lets your hips touch the ground through the thin spots, which bypasses the insulation entirely. A pad used on a slope lets you slide onto the cold ground at the edge. A pad with a slow leak loses both comfort and insulation through the night. The test measures a properly inflated pad lying flat, and the table assumes the same. Check the firmness right before you go to sleep, because air pads lose pressure as the temperature drops, and top up the air if the pad feels soft.

      Common mistakes

      The most common mistake is buying for the bag rating instead of the night. A camper with a bag rated to 20 degrees buys a pad rated R 2 because the bag is the warm part of the system, then sleeps cold on a 25-degree night because the pad cannot hold heat against the ground. The bag rating assumes a pad of R 4 or R 5, and a pad rated R 2 does not meet that assumption. Match the pad to the night first, and check it against the bag's assumption second.

      The second mistake is trusting a non-ASTM R-value. A pad from an unknown brand that claims R 6 for very little money is usually claiming a number that was never measured to the standard, and it will not perform like an R 6 pad from a manufacturer that tests to ASTM F3340. The standard exists precisely to make that comparison honest, and a missing ASTM label is a reason to be skeptical, not a reason to assume the number is close enough. For warm weather the difference hardly matters. Below freezing it matters a great deal.

      The third mistake is ignoring the ground. Campers plan around the air temperature and forget that spring soil is colder than fall soil, that rock draws heat faster than dirt, and that snow is a different problem from cold dirt. The tool's ground adjustment exists because the table assumes dry ground, and every night on snow or rock is a night the table understates. If your trip involves snow, add the point and bring the foam pad.

      The fourth mistake is confusing thickness with warmth. A thick pad that is not insulated is a comfortable pad that leaves you cold, and a thin pad that is well insulated is a warm pad that looks unimpressive in the store. Read the R-value, check for the ASTM label, and let the thickness decide comfort, not warmth. The same confusion runs the other way: some campers assume a thin foam pad cannot be warm, when a foam pad rated R 2 is exactly right for a summer night and the correct second layer in a winter stack.

      The fifth mistake is forgetting the forecast's error. Mountain weather runs colder than valley forecasts, cold air pools in hollows and valley bottoms, and a clear night radiates heat away faster than a cloudy one. If the forecast says 30 degrees, the hollow where you pitch the tent may reach 25. The tool steps up to the colder row between table temperatures, which builds in a little margin, but it cannot see your campsite. Enter the coldest plausible low, not the forecast's headline number, and carry the extra half point of R-value when the forecast is uncertain. Planning the route itself helps too: our Hiking Time Estimator works out how long the approach hike will take, our Hiking Water Planner works out how much water to carry, our Trekking Pole Size Finder sizes poles for the terrain, and our Mountain Climbing Season Planner picks the season for the climb, so the pad decision sits inside a trip plan rather than standing alone.

      Frequently asked questions

      What R-value do I need for a 30-degree night?

      For a 30-degree Fahrenheit night, the Exped and SectionHiker table gives a minimum of R 2 for a warm sleeper on dry ground, R 2.5 for an average sleeper, and R 3 for a cold sleeper, with 1 more point if you are sleeping on snow. That sits at the bottom of REI's cool weather band, which runs from R 2 to R 3.9 for nights around freezing. A pad rated R 3 to R 4 covers a 30-degree night for most sleepers with margin, and it is the range most three-season backpackers carry. If the forecast could dip below freezing, size for the colder number: a low of 25 degrees needs R 3 as a warm sleeper, and a cold sleeper on snow at 25 degrees needs R 5.

      What does R-value mean on a sleeping pad?

      R-value measures thermal resistance: how strongly the pad resists heat flowing from your body into the ground. The higher the number, the more insulation sits between you and the cold earth. REI explains the scale simply: a pad rated R 2 is twice as warm as a pad rated R 1, because it lets half as much heat through. Since 2020, R-values have been measured to the ASTM F3340 standard, which defines one test method for every manufacturer, so an R 4 pad from one brand insulates about the same as an R 4 pad from another. Before the standard, every company measured differently and the numbers could not be compared. R-value says nothing about comfort, thickness, or weight, which is why a thick uninsulated pad can feel soft and still leave you cold.

      Do R-values add when you stack two pads?

      Yes. R-values are additive, so two pads stacked give the sum of their R-values. A foam pad rated R 2 under an air pad rated R 4.5 gives you R 6.5, which is winter territory reached with two ordinary pads. Both SectionHiker and REI state the rule, and REI recommends the combination for winter camping: the foam pad adds insulation, protects the air pad from punctures, and blocks the moisture that collects under a pad on cold ground. Put the foam pad on the bottom and the air pad on top, where it gives you the comfort and the fine insulation next to your body. This tool's stacking mode adds the two pads for you, compares the total against your minimum, and sizes the second pad if you leave it blank.

      What R-value do I need for winter camping?

      For a 0-degree Fahrenheit night, the table gives a minimum of R 5 for a warm sleeper on dry ground, R 6 for a cold sleeper, and R 7 for a cold sleeper on snow. REI puts 0-degree nights in its extremely cold weather band, R 5.5 and up, which is about half a point warmer than the table's minimum. Most winter campers reach those figures by stacking: a foam pad rated R 2 under an insulated air pad rated R 4.5 gives R 6.5, which covers a 0-degree night on snow for an average sleeper exactly. Below 0 degrees the minimum climbs about one point per 10 to 15 degrees, so a -15 degree night needs R 6 as a warm sleeper and R 8 as a cold sleeper on snow. At those temperatures the pad is one part of a winter system that also needs a bag rated for the cold and the experience to use it.

      What R-value do I need for snow?

      Snow adds 1 to the table figure, because snow and frozen ground draw heat away faster than dry dirt. On a 0-degree night on snow, an average sleeper needs R 6.5: the table base of R 5, plus 0.5 for an average sleeper, plus 1 for snow. A cold sleeper on snow at the same temperature needs R 7. The standard winter setup is a closed-cell foam pad under an insulated air pad, which REI recommends because the foam adds insulation, protects against punctures, and blocks the moisture that collects under a pad on cold ground. The snow adjustment in this tool is a planning allowance rather than a published figure: the published figures are the table itself and the cold sleeper's plus-1, and the tool labels the ground adjustments as its own.

      Is a higher R-value always better?

      No. A higher R-value means more insulation, but it also usually means more weight, more bulk, and more cost, and on a warm night the extra insulation is weight you carry for nothing. Above 50 degrees any pad rated R 1 or higher covers the night for warmth, so a summer camper gains nothing from an R 5 pad except a heavier pack. REI's advice is to pick two qualities to prioritize, because no pad is best at everything: warmth, weight, packability, comfort, durability, and price all trade against each other. The right R-value is the minimum for the coldest night you expect, plus a little margin for a forecast that runs cold. Buy for your coldest realistic night, not for the coldest night you can imagine, and stack a foam pad under your three-season pad for the occasional winter trip instead of buying a dedicated winter pad you will rarely use.

      What R-value pad goes with my sleeping bag?

      Match the pad to the night, and check it against what your bag's rating assumes. Sleeping bag temperature ratings assume a pad is underneath: REI says ratings assume an R-4 pad, and SectionHiker notes that EN ratings are predicated on R-5 or higher, while the international test lays the bag on a mat of about R 4.8. If your pad is thinner than that, your bag will not live up to its rating, because heat escapes downward through the pad no matter how much loft is on top. As a rule, a 30-degree bag pairs with a pad for a 30-degree night, which is R 2 for a warm sleeper and R 3 for a cold sleeper, and a 0-degree bag pairs with a pad for a 0-degree night, which is R 5 for a warm sleeper and R 6 for a cold sleeper. Quilt sleepers should read the table strictly, because a quilt has no insulation underneath at all and the pad does the whole job below the body.

      How is sleeping pad R-value measured?

      Sleeping pad R-value is measured to ASTM F3340, the Standard Test Method for Thermal Resistance of Camping Mattresses Using a Guarded Hot Plate Apparatus. The pad is held under a constant compressive force between a heated plate and a cold plate, and the lab measures the steady flow of heat down through the pad's thickness. The standard was first published as F3340-18 and the current edition is F3340-22; the major brands adopted it from 2020 onward, after REI, Exped, Therm-a-Rest, Sea to Summit, NEMO, Big Agnes, and Klymit spearheaded it. The standard itself notes that the laboratory value will not always match real-world performance, because heat also escapes at the pad's edges and through surfaces you are not covering. Pads with no ASTM rating may carry numbers that were never measured to the standard, so check for the ASTM label before comparing a pad against the table, especially for anything below freezing.

      Sources

      The R-value to temperature table is the Exped recommendation as published by SectionHiker in Understanding Sleeping Pad Temperature Ratings, updated 18 May 2025 and re-checked 21 November 2026. The warmth bands, the pad and bag pairing table, the foam pad guidance, and the winter stacking advice come from REI's Sleeping Pad Buying Guide, re-checked 21 November 2026. The ASTM F3340 standard is published by ASTM International under subcommittee F08.22 on camping softgoods; the current edition is F3340-22. Published pad R-values used as examples are the manufacturers' specs: the Therm-a-Rest NeoAir XTherm NXT at R 7.3, the NeoAir XLite NXT at R 4.5, and the Z Lite Sol at R 2.0, as listed in the manufacturer's catalog and confirmed by Outdoor Gear Lab's XTherm NXT review. The NEMO Switchback at R 2.0 and the Exped FlexMat Plus at R 2.2 are from the same review and from SectionHiker's FlexMat review. Model names appear only as examples of published R-values, not as recommendations. The sleeper and ground adjustments are this tool's planning allowances except for the cold sleeper's plus-1, which follows SectionHiker, and they are labeled as such in the tool.