Skip to content

Snowshoe Size Finder

Your weight without the pack. 30 to 400 lb.

Everything you carry: pack, water, extra layers. MSR suggests adding 10 to 15 lb for a simple day on the trail if you do not weigh it. 0 to 100 lb.

The snow you will meet most of the time. Powder needs the most flotation.

Steep ground favors a shorter, more maneuverable shoe when the rating still covers your load.

The boot you will wear, in US men's sizes. Checks the size against the makers' binding ranges. US 4 to 16.

Your snowshoe size

What each maker says for this load

How the size was worked out

      This tool sizes snowshoes from the makers' published charts for general planning only. It is not a guarantee of fit: snow, terrain, boot, and binding all change the real answer. Check the maker's current chart for the model you buy, try the binding on with your boots, and rent before buying when unsure.
      What size snowshoes do I need? Size by total loaded weight, body weight plus pack: a 150 lb hiker with a 10 lb pack carries 160 lb and fits a 22-inch snowshoe on packed trails, a 25-inch shoe on soft snow, and a 25-inch shoe with flotation tails in deep powder. Enter your weight, pack, snow, and terrain above for a size from the MSR, Tubbs, and Atlas charts side by side, with binding fit and tails advice.

      Last reviewed: 21 November 2026. Reviewed every 180 days; next review due 19 May 2027.

      How to use the Snowshoe Size Finder

      Enter your body weight, the weight of the pack you will carry, the snow you will meet most of the time, and the terrain you will walk. Add your US men's shoe size if you want a binding check. The tool answers with a snowshoe length in inches, the total load it sized for, the deck area behind the pick, and a brand-by-brand comparison showing what MSR, Tubbs, and Atlas each say for your load. Where the makers disagree, the tool says so instead of hiding it.

      Start with your body weight in pounds, without the pack. Then add the pack weight: everything you will carry, including the pack itself, water, food, extra layers, and safety gear. The two numbers add up to the total load, and the total load is the number every maker's chart wants. A 170 lb hiker with a 15 lb pack is a 185 lb load, and sizing from 170 lb alone would undersize the shoe by a full step in soft snow. If you do not weigh the pack, MSR suggests adding 10 to 15 lb for a simple day on the trail as a starting point. Our Backpack Base Weight Calculator helps you weigh the pack properly before you size the shoes.

      Pick the snow type you will meet most of the time, not the snow you dream about. Packed snow means groomed trails, broken tracks, and settled snow that holds your weight. Soft snow means untracked, settled snow off the beaten track. Soft and deep snow means fresh powder, the light dry snow that offers almost no support. MSR calls this the majority rule: size the shoe for the conditions you will meet on most trips, because a shoe bought for one huge powder day will feel oversized on the other 80 percent of your outings. If the powder days matter, flotation tails are the answer, not a longer shoe.

      Pick the terrain honestly. Flat or gently rolling trails put flotation first. Rolling terrain is the middle ground most hikers walk. Steep backcountry terrain favors a shorter, more maneuverable shoe with aggressive traction, and the tool steps down one size on steep ground when the shorter shoe's rating still covers your load. In powder it never steps down, because flotation wins there.

      The shoe size field is optional. Enter the US men's size of the boot you will wear, and the tool checks it against the makers' binding ranges: MSR men's bindings fit US 6 to 13 and women's US 5 to 13, Tubbs men's Flex bindings fit US 8 to 13 and women's US 6 to 11. A boot outside those ranges needs a different binding, and the tool will say so.

      Three worked examples sit below the form. Try the day hike first: 170 lb, a 15 lb pack, soft snow, rolling ground. Then try the powder day: 200 lb, a 25 lb pack, deep powder, steep ground. The answers change by a full size, which is the whole point of the tool.

      How snowshoe sizing works

      A snowshoe is a flotation device. It spreads your weight over a larger surface so you do not sink knee-deep into the snow, a misery snowshoers call post-holing. The amount of flotation you need decides the length: more weight or softer snow needs more surface area, which means a longer shoe. Less weight or firmer snow needs less, which means a shorter shoe that is lighter, easier to turn, and less tiring to swing all day.

      Length is the number on the box, and it is the number this tool returns. Adult snowshoes run from about 21 inches to 36 inches long. The common sizes are 22, 25, and 30 inches, with 35- and 36-inch shoes at the heavy end and 17- and 20-inch shoes for children. Width matters too: most adult shoes are 8 inches wide, with 30-inch models widening to 9 inches and 36-inch models to 10 inches. A 25-inch shoe with an 8-inch-wide deck gives about 200 square inches of deck before the frame taper, and a 200 lb load on it presses about 1.00 lb on each square inch. The tool shows this deck-area figure for every pick so you can compare sizes on flotation, not just on length.

      The true deck area is smaller than length times width, because snowshoe frames taper toward the tail. Outdoor Gear Lab measured 143 square inches of deck on a 22-inch MSR Lightning Ascent whose frame measures 7.25 by 22 inches, about 90 percent of the length-times-width figure. Treat the tool's deck area as a planning figure for comparing sizes, not as a laboratory measurement.

      Three inputs drive the size, in this order. Total load comes first: it sets the weight band, and no other input can move you out of your band. Snow type comes second: it moves the pick by a full size within the band, because powder offers far less support than packed snow. Terrain comes third: it can step the pick down one size on steep ground, when the shorter shoe still covers the load. Boot size never changes the length; it changes the binding advice only.

      The single most common sizing mistake is sizing from body weight alone. Every maker's chart defines user weight as body weight plus everything carried. Tubbs prints it on the chart itself: user weight is body weight plus load. Atlas prints the same rule: load equals the user's bodyweight plus gear. MSR tells buyers to count body weight plus the gear and clothing worn on most outings, and to include the backpack contents. A winter pack is heavier than people remember: GearJunkie puts a day-trip load at about 20 lb above body weight and an overnight or mountaineering load at 30 to 60 lb above it. Weigh the pack packed, on a bathroom scale, before you trust any chart.

      The MSR sizing chart

      MSR, part of Cascade Designs, publishes the only major chart that crosses weight with snow type in one table, and this tool uses it as its base table. The chart reads as follows, with weight including gear:

      Your weightPacked snowSoft snowSoft and deep snow
      90 to 125 lb22 in22 in25 in, or 22 in with tails
      125 to 175 lb22 in25 in, or 22 in25 in, or 22 in with tails
      175 to 225 lb22 in25 in, or 22 in with tails30 in with tails, or 22 in with tails, or 25 in with tails
      225 lb and over22 in or 25 inTails combinationsTails combinations

      Read the chart with two rules the tool applies for you. First, the bands share their edges: 125 lb appears in two rows, as do 175 lb and 225 lb. The tool reads each edge into the higher band, so exactly 125 lb reads the 125 to 175 lb row, exactly 175 lb reads the 175 to 225 lb row, and exactly 225 lb reads the 225 lb and over row. Second, where a cell offers two answers, the tool takes the first listed size as the headline pick and notes the alternative: the 125 to 175 lb soft-snow cell lists 25 inches first, so the pick is 25 inches, with the 22-inch option noted for firmer soft snow.

      Two things about the MSR chart deserve an honest note. The chart's metric column misprints the 175 to 225 lb band as 79 to 120 kg; 225 lb is 102 kg, not 120 kg, and this tool converts correctly rather than repeating the misprint. And the chart disagrees with MSR's own product ratings at the top of the packed column: the chart lists a 22-inch shoe on packed snow for loads up to 225 lb, but the 22-inch Lightning Ascent is rated only to 180 lb loaded. The tool resolves that tension in favor of the rating: a 200 lb load on packed snow steps up to a 25-inch shoe, and the tool shows the disagreement rather than hiding it.

      MSR's own advice around the chart is worth following. Size for the majority of your trips, not for the biggest storm of the year. The vast majority of people are served well with a pair of 22-inch or 25-inch snowshoes and tails, in MSR's words. Buy the smaller base shoe for the trails you walk most weeks, and add tails for the deep days and the heavy pack. The chart is published in MSR's snowshoe sizing guide, originally published 10 November 2020.

      The three makers' charts side by side

      MSR, Tubbs, and Atlas each publish per-model load ratings, and they do not line up exactly. The tool checks your load against all of them and shows each maker's smallest covering shoe. Here are the ratings the tool uses, verified against the makers' live charts and retailer spec sheets on 21 November 2026.

      MSR Lightning Ascent

      MSR's flagship backcountry shoe comes in 22, 25, and 30 inches, all 8 inches wide, with add-on Lightning Tails that add 5 inches of flotation on demand. The men's ratings are 22 inches up to 180 lb, 25 inches 120 to 220 lb, and 30 inches 150 to 280 lb. With tails, the ratings rise to 250 lb, 280 lb, and 300-plus lb. The women's Lightning Ascent comes in 22 and 25 inches, about three-quarters of an inch narrower for a more natural gait, rated up to 180 lb and 120 to 210 lb, or up to 240 lb and 270 lb with tails. The 25-inch men's pair weighs about 4 lb. MSR notes that the 30-inch shoe is not recommended for firm snow or established trails: it is a soft-snow shoe. Full specs are on the Backcountry product page.

      Tubbs Flex series

      Tubbs Flex shoes use a composite Torsion Deck instead of a tubular frame, and they size differently from the Mountaineer line. The Flex STP, RDG, and TRK models run 22, 24, and 28 inches: 22 inches for 80 to 160 lb, 24 inches for 120 to 200 lb, and 28 inches for over 190 lb, with no upper limit published for the 28-inch shoe. The Flex ALP runs 21, 25, and 29 inches with the same weight bands. Men's Flex bindings fit US shoe sizes 8 to 13 and women's 6 to 11. The chart is reproduced in full on the Tubbs Flex STP listing, including the footnote that user weight is body weight plus load.

      Tubbs Mountaineer

      The Mountaineer is Tubbs' traditional tubular-frame backcountry shoe, in 25, 30, and 36 inches for men: 25 inches for 120 to 200 lb, 30 inches for 170 to 250 lb, and 36 inches for 220 to 300 lb. The frames measure 8 by 25, 9 by 30, and 10 by 36 inches, which is where the tool's deck widths come from. The women's Mountaineer runs 21, 25, and 30 inches, rated 80 to 150 lb, 120 to 200 lb, and 170 to 250 lb. The women's ratings are listed in the Outdoor Gear Lab review.

      Atlas

      Atlas publishes one standard chart across its mountain models: 25 inches for 120 to 200 lb, 30 inches for 150 to 250 lb, and 35 inches for 180 to 300-plus lb, with load defined as the user's bodyweight plus gear. The Helium trail line runs 23 inches for 80 to 160 lb and 26 inches for 150 to 220-plus lb, with a 30-inch model listed at 200 to 270 lb. Women's models run 23 inches for 80 to 160 lb and 27 inches for 120 to 200-plus lb. Atlas also publishes youth sizes: the Mini 17-inch for 30 to 80 lb and the Spark 20-inch for 50 to 120 lb. The full chart is reproduced on the Atlas Helium BC listing, and Atlas's own selection advice is on the Atlas snowshoe selection page: size by body weight plus anything carried, go larger for deep dry powder than for heavy or packed snow, and pick aggressive traction with a heel lift for climbing.

      The lineups at a glance

      Maker and modelLengthsLoad range
      MSR Lightning Ascent (men's)22, 25, 30 inUp to 180 lb; 120 to 220 lb; 150 to 280 lb
      MSR Lightning Ascent (women's)22, 25 inUp to 180 lb; 120 to 210 lb
      Tubbs Flex STP, RDG, TRK22, 24, 28 in80 to 160 lb; 120 to 200 lb; over 190 lb
      Tubbs Flex ALP21, 25, 29 in80 to 160 lb; 120 to 200 lb; over 190 lb
      Tubbs Mountaineer (men's)25, 30, 36 in120 to 200 lb; 170 to 250 lb; 220 to 300 lb
      Tubbs Mountaineer (women's)21, 25, 30 in80 to 150 lb; 120 to 200 lb; 170 to 250 lb
      Atlas standard25, 30, 35 in120 to 200 lb; 150 to 250 lb; 180 to 300-plus lb
      Atlas Helium23, 26, 30 in80 to 160 lb; 150 to 220-plus lb; 200 to 270 lb
      Atlas youth17, 20 in30 to 80 lb; 50 to 120 lb

      Notice how the lineups differ in shape. MSR and Atlas top out at 30 and 35 inches with tails or a plus rating past 300 lb. Tubbs Flex tops out at 28 inches with an open-ended rating, and the Mountaineer goes to 36 inches. A 200 lb loaded hiker fits an MSR 25-inch, a Tubbs Flex 24-inch, a Tubbs Mountaineer 25-inch, and an Atlas 25-inch shoe: four makers, three different lengths, all correct for the same load. That is why the tool reports a size class and then shows each maker's nearest shoe, instead of pretending one number fits every brand.

      Where the charts disagree

      The three makers agree over most of the weight range, and they disagree at three boundaries. This tool shows the disagreement at the load where it bites, because a shopper who only reads one chart can buy the wrong size.

      At 161 to 180 lb, the 22-inch shoe is contested. MSR rates its 22-inch Lightning Ascent to 180 lb, so a 170 lb load fits the 22-inch shoe on MSR's chart. Tubbs rates its 22-inch Flex shoes to 160 lb, so the same load needs the 24-inch Flex. If you buy Tubbs at 170 lb, you buy the 24-inch shoe; if you buy MSR, the 22-inch shoe is within its rating. The tool's headline follows the MSR chart and flags the Tubbs difference.

      At 201 to 220 lb, the 25-inch shoe is contested. MSR rates its 25-inch Lightning Ascent to 220 lb, so a 210 lb load fits the 25-inch shoe on MSR's chart. Tubbs and Atlas both top their 25-inch shoes at 200 lb, so the same load needs the 30-inch Mountaineer or the 30-inch Atlas. Only MSR stretches the 25-inch shoe past 200 lb.

      At 251 to 280 lb, the 30-inch shoe is contested. MSR rates its 30-inch Lightning Ascent to 280 lb, so a 260 lb load fits the 30-inch shoe on MSR's chart. Tubbs and Atlas both top their 30-inch shoes at 250 lb, so the same load needs the 36-inch Mountaineer or the 35-inch Atlas. Only MSR stretches the 30-inch shoe past 250 lb.

      There is also a disagreement inside MSR's own publications, described above: the quick chart lists a 22-inch shoe on packed snow up to 225 lb, while the 22-inch Lightning Ascent is rated only to 180 lb. The tool resolves it in favor of the rating and shows the conflict. And the Flex 28-inch rating has no top at all: Tubbs publishes "over 190 lb" with no upper limit, so the tool cannot say where the 28-inch Flex stops covering a load. Treat an open-ended rating as a reason to ask the maker, not as unlimited capacity.

      REI's long-running advice lines up with the 180 lb line: a 2016 summary of REI's guide says that a hiker and pack weighing less than 180 lb take a 22-inch shoe, and over that a 25-inch shoe or longer. That matches the MSR 22-inch ceiling exactly, and it is the oldest form of the rule the charts still follow.

      Snow conditions change your size

      Snow is not one material. Fresh powder is mostly air: cold, dry, unconsolidated snow offers almost no support, so the shoe must be long to spread the load. Settled snow has bonded into a denser pack that carries more weight per square inch. Packed trails and groomed routes are denser still, and on them traction matters more than flotation. The same hiker needs a different shoe on each.

      The MSR chart quantifies the difference. A 150 lb load takes a 22-inch shoe on packed snow, a 25-inch shoe on soft snow, and a 25-inch shoe with tails as the powder option. A 200 lb load takes a 22-inch shoe on packed snow by the chart (stepped up to 25 inches by the rating check), a 25-inch shoe on soft snow, and a 30-inch shoe with tails in soft and deep snow. Snow type moves the answer by a full size, sometimes two.

      Think about snow at two scales, as MSR suggests. At the macro scale, a deep powdery mid-winter snowpack in the Rockies or northern Minnesota needs more flotation than the dense maritime snowpack of the Sierras or the Pacific Northwest. At the micro scale, ask whether you will mostly walk off-trail in unconsolidated snow or on packed-out trails where traction is the bigger concern. The answer to the micro question decides the size more often than the region does.

      Wet snow complicates the picture in the other direction. Dense, wet spring snow supports more weight than dry powder, so a shoe sized for mid-winter powder will feel oversized in spring. If you snowshoe year-round, size for the mid-winter snow you meet most often and accept that the shoe is longer than spring needs. If you only go out in spring, the packed column of the chart is the honest one.

      Powder is also where flotation tails earn their keep. A 25-inch shoe with tails gives the flotation of a longer shoe on the deep days and the maneuverability of the shorter shoe the rest of the season. The tool suggests tails whenever the snow is powder and the pick is 22 or 25 inches, whenever the load passes 280 lb, and whenever the load is 225 lb or more on soft snow, because MSR's chart answers that cell with tails combinations.

      Terrain changes your size

      Terrain pulls the size in the opposite direction from snow. On flat trails, length costs little: the trail is wide, the turns are gentle, and the extra flotation is free. On steep, narrow, tree-filled ground, length costs a lot: a long shoe catches on roots and rocks, clips your own ankles on switchbacks, and fights every turn. That is why the tool steps down one size on steep ground when the shorter shoe's rating still covers the load.

      The step-down has a hard limit. It never fires in powder, because flotation wins there no matter how steep the ground. It never fires when the shorter shoe's rating does not cover the load: a 200 lb hiker on steep soft snow stays on the 25-inch shoe because the 22-inch shoe is rated only to 180 lb. And it never fires below 22 inches, the shortest adult size. A 140 lb hiker on steep soft snow steps down from the chart's 25-inch pick to a 22-inch shoe, because the 22-inch rating covers 140 lb with room to spare. A 170 lb hiker on the same ground steps down too, landing exactly on the Tubbs disagreement band: MSR's 22-inch rating covers 170 lb, Tubbs' does not, and the tool says so.

      On steep ground, the frame and traction matter more than the length. Look for aggressive steel crampons underfoot, traction rails or a serrated frame edge for sidehills, and a heel lift that flips up with a pole tip to save your calves on long climbs. Atlas's selection guide makes the same point: climbers want aggressive traction and a heel lift, runners want the lightest shoe with less traction. The Mountaineers' course guidance adds that aluminum crampons are not recommended for serious mountain use, steel being much more durable, and that 36-inch and longer shoes are not recommended for their field trips. If the route needs an ice axe, it has left snowshoe country.

      Rolling terrain is the default for a reason: most snowshoeing happens on rolling ground, and the chart's picks assume it. Flat terrain never changes the pick either. Only steep ground moves the size, and only by one step down. If you are planning a mountain trip, our Mountain Climbing Season Planner helps pick the season, and our Hiking Time Estimator works out how long the day will take on snow.

      Flotation tails

      Flotation tails are short extensions that clip onto the back of the shoe and add length on demand. MSR invented the idea for exactly the problem this tool solves: the shoe that fits most trips is too short for the deepest days, and the shoe that fits the deepest days is too long for most trips. Lightning Tails add 5 inches; the Evo Trail tails add 6 inches. With tails, the 22-inch Lightning Ascent carries up to 250 lb, the 25-inch up to 280 lb, and the 30-inch past 300 lb.

      Tails change the buying decision. Instead of buying a 30-inch shoe for a 200 lb load that meets powder twice a season, buy the 25-inch shoe and add tails for the powder days. The tool's tails advice follows MSR's chart: tails are suggested for powder days at 22 and 25 inches, for loads past 280 lb, and for loads of 225 lb or more on soft snow. Tails are not suggested for packed snow at ordinary weights, where the base shoe already floats.

      Tails have limits. They add flotation at the back of the shoe, which changes the balance slightly and adds swing weight. They do not add traction, so they do not help on steep icy ground. And they are an MSR-only answer: Tubbs and Atlas do not offer tails, so a Tubbs or Atlas buyer who needs more flotation buys the longer shoe. If tails are part of your plan, that is a reason to buy into the MSR line.

      Bindings and boot fit

      The binding is the part of the snowshoe you will curse or praise all day. It must hold the boot firmly without pinching, release snow instead of packing it, and adjust with gloves or mittens on. A binding that fits on paper can still pinch or slip on the trail, which is why every maker and every guide says the same thing: try the binding on with the boots you will wear before you buy.

      Binding ranges are published in US shoe sizes, and they differ by maker and by model. MSR bindings fit men's US 6 to 13 and women's US 5 to 13. Tubbs Flex men's bindings fit US 8 to 13 and women's US 6 to 11. Atlas adult bindings cover most adult insulated winter boots. The tool checks your shoe size against all three ranges: a US men's 7 boot fits MSR and Tubbs women's bindings but sits below the Tubbs men's range, which starts at US 8; a US men's 14 boot is above every standard range and needs MSR's TriFit or DuoFit strap bindings on the Evo Ascent and Trail models, which MSR recommends for large boots and large-shelled boots such as snowboard and plastic mountaineering boots.

      Women's bindings are not just smaller men's bindings. MSR's women's shoes are about three-quarters of an inch narrower than the equivalent men's shoes, after gait analysis showed the narrower frame gives a more natural stride for most women. Tubbs tapers the tail on women's models for the same reason. A narrow gait benefits from the narrower shoe regardless of gender, and MSR says so plainly.

      Binding styles vary: pull webbing, ratchet straps, BOA cable laces, and rotating toe cords. Pull webbing and BOA bindings are the quickest to get in and out of, which matters when your hands are cold. Rotating toe cords let the tail drop as you lift your foot, shedding snow with each step. Whatever the style, check three things in the shop: the boot sits centered over the pivot point, the straps tighten without tools, and you can open the binding with mittens on.

      Frames, crampons, and heel lifts

      The frame is the skeleton of the snowshoe, and there are three kinds. Tubular aluminum frames are the classic design: a bent tube with a fabric deck, light and proven, used by Tubbs Mountaineer and Atlas. Flat-stock frames are a newer design, exemplified by the MSR Lightning line: a flat bar bent into an oval with serrated edges that bite on traverses. Composite decks, used by Tubbs Flex, mold the deck and frame into one piece that twists with uneven ground, preserving a natural gait at the cost of some bite on ice.

      Traction comes from crampons and rails. Every backcountry shoe has a steel toe crampon under the ball of the foot; better shoes add a heel crampon and traction rails along the sides. The Lightning's serrated frame edge runs the full perimeter, so the whole edge bites on a traverse instead of only the patch underfoot. The Mountaineers' guidance is blunt: steel crampons, not aluminum, for mountain use. On packed trails and gentle ground, modest traction is enough, and an aggressive crampon is just weight.

      The heel lift, also called a heel riser or Televator, is a small bar that flips up under the heel on climbs so the foot stays level while the shoe points uphill. It saves calves and Achilles tendons on long ascents and is worth having on any shoe that will see steep ground. Atlas fits a 12-degree heel lift on its Helium trail shoes; Tubbs fits a 19-degree ActiveLift on the Mountaineer and Flex ALP. If your routes are flat, you will never flip it up, and it costs nothing to have.

      Weight matters more than it looks on paper. A pair of snowshoes weighs about 4 lb, and you lift that weight with every step for hours. A pound saved on the shoes is worth more than a pound saved in the pack, because the shoes swing at the end of your legs. That is the real argument for the shorter shoe: the flotation you give up is small, and the energy you save is large. Our Trekking Pole Size Finder sizes the poles that go with the shoes, and our Hiking Water Planner works out the water weight that lands in the pack.

      Youth snowshoe sizing

      Children need snowshoes sized by the same rule, total load, but the adult charts start at 90 lb and do not cover them. The youth ranges come from Atlas: the Mini 17-inch shoe covers 30 to 80 lb and the Spark 20-inch covers 50 to 120 lb. The Tubbs Flex 22-inch shoe covers 80 to 160 lb, which bridges the top of the youth range into adult sizes. The tool reads loads under 90 lb from these ranges: under 50 lb takes the 17-inch shoe, 50 to 79 lb the 20-inch, and 80 to 89 lb the 22-inch.

      Children outgrow snowshoes fast, and their loads change as they grow, so renting is often the better buy for a child who snowshoes a few times a season. Check the binding fit the same way as for adults: youth bindings are sized for smaller boots, and a boot that swims in the binding will slip. A child who is already over 90 lb loaded reads the adult chart like anyone else.

      Do not size a child into an adult shoe for growing room. An oversized shoe is heavy, clumsy, and tiring, and a tired child stops enjoying the day. The right size is the one that fits this winter's load, not next winter's.

      Worked examples

      Five hikers, five answers, each worked through the tool so you can check the logic against your own case. Every figure below is the tool's own output for the stated inputs.

      HikerTotal loadSnow and terrainPickWhy
      150 lb, 10 lb pack160 lbPacked, rolling22 inMSR chart gives 22 in for 125 to 175 lb on packed snow; the 22 in rating covers 160 lb.
      185 lb, 15 lb pack200 lbSoft, rolling25 inMSR chart gives 25 in for 175 to 225 lb on soft snow; the 25 in rating covers 200 lb. Deck about 200 sq in, 1.00 lb per sq in.
      200 lb, 25 lb pack225 lbPowder, steep30 inMSR chart gives 30 in for 225 lb and over in deep snow; steep ground never steps down in powder. Avalanche warning applies.
      130 lb, 10 lb pack140 lbSoft, steep22 inMSR chart gives 25 in for 125 to 175 lb on soft snow, but steep ground steps down to 22 in because the 22 in rating covers 140 lb.
      260 lb, 20 lb pack280 lbPowder, rolling30 inMSR chart gives 30 in for 225 lb and over in deep snow, exactly at the 30 in rating of 280 lb. Tubbs and Atlas top their 30 in shoes at 250 lb, so the tool flags the disagreement.

      The second example is the hand-check case for this tool: 200 lb on soft snow reads the MSR chart row for 175 to 225 lb, soft column, which gives 25 inches, and the 25-inch Lightning Ascent rating of 120 to 220 lb covers 200 lb. Tubbs Mountaineer and Atlas both rate their 25-inch shoes to 200 lb, exactly at the load, and Tubbs Flex gives the 24-inch shoe. All four makers agree on the size class, and the deck math balances: 25 inches times 8 inches is 200 square inches, and 200 lb over 200 square inches is 1.00 lb per square inch.

      Buying checklist

      Before you buy, run through this list. It takes five minutes and saves a season of regret.

      Weigh yourself in winter clothes with the pack on. The bathroom scale does not lie, and the chart wants the dressed-and-loaded number. If the pack is not weighed, add 10 to 15 lb for a day trip and 30 to 60 lb for an overnight trip, and re-check the size if the pack grows.

      Decide the snow you will meet most weeks. If most of your winter is packed trails with two powder days a season, buy for the packed trails and add tails. If most of your winter is untracked powder, buy the longer shoe.

      Try the binding on with your boots. Bring the boots to the shop. Tighten the binding with gloves on, walk the shop floor, and check that the boot stays centered and the straps do not slip. If you buy online, check the return policy first.

      Check the rating for the exact model, not the line. Ratings vary within a brand: the Flex 22-inch tops at 160 lb while the Lightning 22-inch tops at 180 lb, and the women's Lightning 25-inch tops at 210 lb while the men's tops at 220 lb. The model page governs, not the brand name.

      Consider renting first. Many outdoor shops and REI stores rent snowshoes, and a rental day answers every question this tool cannot: how the binding feels after three hours, whether the shoe clips your ankles, whether the length suits your stride. Renting is also the right answer for children and for a first trip before committing to a purchase.

      Budget for the rest of the kit. Poles with large baskets keep you upright and stop the poles sinking into soft snow; our Trekking Pole Size Finder sizes them. Gaiters keep snow out of your boots. A pack that fits the load matters as much as the shoes; our Backpack Capacity Planner sizes it, and our Backpacking Food Planner plans the food weight that goes inside it. Washington Trails Association puts typical snowshoe prices between 80 and 400 dollars, with bindings and traction accounting for most of the spread.

      Planning the day around the shoes

      The right size is only the start of the day. Winter days are short, snow slows every pace, and a snowshoe trip needs more planning than the same route in summer. Start with time: our Hiking Time Estimator runs five methods side by side, including Naismith's rule and AMC book time, and gives a turn-back time. Snowshoeing runs slower than the summer pace on the same trail, so treat the estimate as optimistic and start early.

      Water is the weight most people forget. Winter air is dry, the work is hard, and thirst arrives late in the cold. Our Hiking Water Planner works out how much to carry, and the water weight belongs in the pack weight you enter above. Food weight counts too, especially on overnight trips where the pack can reach 40 lb or more and push the load into the next size.

      Overnight winter trips add a sleeping system to the load. Our Sleeping Pad R-Value Finder matches the pad to the night temperature, and the pad, bag, and stove all add pack weight that the snowshoe chart counts. If the trip runs into bear country in the shoulder season, our Bear Canister Size Finder sizes the food storage.

      And if the snow is deep enough to need snowshoes, it may be deep enough to ski. Our Cross-Country Ski Size Finder sizes skis by the same total-load logic for skiers who prefer to glide. Snowshoes win on steep, narrow, and brushy ground; skis win on open rolling terrain and distance.

      Every figure on this page was checked against the makers' live charts on 21 November 2026: the MSR sizing guide on the Cascade Designs site, the Atlas selection page, the Tubbs Flex chart as published by Tubbs retailers, and the Atlas size guide as published by Atlas retailers. Where the makers disagree, the page shows the disagreement. The next review is due 19 May 2027.

      Frequently asked questions

      What size snowshoes do I need for my weight?

      Size by total loaded weight, body weight plus pack, not by body weight alone. As a rough guide on soft snow: 90 to 125 lb takes a 22-inch shoe, 125 to 175 lb takes a 25-inch shoe, 175 to 225 lb takes a 25-inch shoe, and 225 lb and over takes a 30-inch shoe. On packed snow you can often go one size shorter, and in deep powder you go one size longer. Enter your weight, pack, snow, and terrain above for the exact pick from the makers' charts.

      Do I count my pack when sizing snowshoes?

      Yes. Every maker's chart rates user weight as body weight plus everything carried: Tubbs prints it on the chart, Atlas defines load as bodyweight plus gear, and MSR tells buyers to count body weight plus gear and clothing. A 170 lb hiker with a 15 lb pack is a 185 lb load. If you do not weigh the pack, MSR suggests adding 10 to 15 lb for a simple day on the trail, and an overnight pack can add 30 to 60 lb.

      What size snowshoes do I need for powder?

      Go one size longer than your packed-trail size, or add flotation tails to the shorter shoe. MSR's chart gives a 125 to 175 lb load a 25-inch shoe in soft and deep snow, against 22 inches on packed snow, and a 175 to 225 lb load a 30-inch shoe with tails. Powder offers almost no support, so the extra surface area is what keeps you from sinking. The tool suggests tails whenever the snow is powder and the pick is 22 or 25 inches.

      Are 25-inch snowshoes big enough for a 200 lb person?

      On soft snow, yes, but exactly at the top of two makers' ratings. MSR rates its 25-inch Lightning Ascent to 220 lb, so a 200 lb load fits with room to spare. Tubbs and Atlas both top their 25-inch shoes at 200 lb, so the same load sits exactly at their limit. In deep powder, size up to a 30-inch shoe or add tails, and if the pack might grow, size up rather than sitting on the limit.

      Should I size down for packed trails?

      Yes. On packed snow, traction matters more than flotation, and a shorter shoe is lighter, easier to turn, and less tiring. MSR's chart gives most adults a 22-inch shoe on packed snow: every load from 90 lb to 225 lb reads 22 inches in the packed column, subject to the rating check, which steps loads over 180 lb up to a 25-inch shoe. If you walk groomed trails most of the time, the packed column is the honest one.

      What is the difference between MSR, Tubbs, and Atlas sizing?

      The lineups differ in length and in ratings. MSR Lightning Ascent runs 22, 25, and 30 inches with add-on tails, rated to 180, 220, and 280 lb. Tubbs Flex runs 22, 24, and 28 inches, rated to 160, 200, and over 190 lb with no top published, while Tubbs Mountaineer runs 25, 30, and 36 inches, rated to 200, 250, and 300 lb. Atlas runs 25, 30, and 35 inches, rated to 200, 250, and 300-plus lb. The makers disagree at three boundaries: 161 to 180 lb, 201 to 220 lb, and 251 to 280 lb.

      Do I need flotation tails?

      Tails are worth adding if you meet deep powder on a 22- or 25-inch shoe, if your load passes 280 lb, or if your load is 225 lb or more on soft snow. MSR's Lightning Tails add 5 inches and lift the 22-inch shoe to 250 lb, the 25-inch to 280 lb, and the 30-inch past 300 lb. Tails let you keep the shorter shoe for packed trails and add flotation only on the deep days. Tubbs and Atlas do not offer tails, so their buyers size up to the longer shoe instead.

      What size snowshoes does a child need?

      Size a child by total load from the youth ranges: Atlas Mini 17-inch shoes cover 30 to 80 lb, Atlas Spark 20-inch shoes cover 50 to 120 lb, and the Tubbs Flex 22-inch shoe covers 80 to 160 lb. A child over 90 lb loaded reads the adult chart. Children outgrow snowshoes fast, so renting is often the better buy, and an oversized shoe bought for growing room is heavy, clumsy, and tiring for a child.