Skip to content

Deer Food Plot Calculator

How big the plot is, 0.1 to 100 acres. A quarter acre is 0.25; a half acre is 0.5.

From your soil test, 3.5 to 9.0. Leave blank if you have not tested: the lime figure becomes a rule-of-thumb estimate.

The species sets the seeding rate and the fertilizer blend. Clover fixes its own nitrogen, so it gets a no-nitrogen blend.

Drilling needs less seed than broadcasting, because more of it germinates. The blend recipe is broadcast either way.

Optional. Your price per pound of seed. For a blend, use one average price per pound for the whole mix.

Optional. Your price for one 50 lb bag of fertilizer.

Optional. Your price for one ton of agricultural lime, delivered and spread if that is how you buy it.

Your food plot plan

How the numbers were worked out

      This tool estimates seed, fertilizer, and lime quantities for a deer food plot from published extension planning rates, for general guidance only. It is not a substitute for a soil test: your lab report sets the exact lime and fertilizer rates for your ground. The rate printed on your seed bag governs for the seed you buy.
      Seed, fertilizer, and lime for a deer food plot come from three published rates times your acres: ladino white clover at 8 lb per acre broadcast, brassicas at 10 lb, cereal grains at 135 lb, and the MDWFP cool-season blend at 70.5 lb. Clover gets 0-20-20 fertilizer at 250 lb per acre because it fixes its own nitrogen; grains and brassicas get 19-19-19 at 300 lb per acre. Lime runs 3.5 tons per acre below pH 5.0 down to none at pH 6.5 and above, or 2 tons per acre as a rule of thumb with no soil test. Enter your acres, species, seeding method, soil pH, and prices above for your seed pounds, fertilizer bags, lime tons, and total cost.

      Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.

      How to use the Deer Food Plot Calculator

      A food plot fails or succeeds on three numbers: how much seed goes down, how much fertilizer feeds it, and how much lime fixes the soil it grows in. Get any one of them wrong and the plot shows it. Too little seed leaves bare ground that weeds claim first. Too much seed crowds the stand, and the plants fight each other for water and light instead of feeding deer. The wrong fertilizer blend wastes money on nitrogen that clover makes for free, or starves brassicas of the nitrogen they need to build leaf and bulb. And lime is the one most plotters skip entirely, even though acidic soil locks up the fertilizer they already paid for. This calculator works out all three numbers for your plot, from your acres, your species, your seeding method, and your soil pH, and prices the whole job at the prices your dealer actually charges.

      To get your plan, follow these steps:

      1. Enter your plot size in acres. Measure the ground you will actually plant, not the whole field. A plot 208 feet by 208 feet is one acre; a plot 100 feet by 100 feet is about 0.23 acres. If your plot is an odd shape, pace the length and width in feet, multiply them, and divide by 43,560, the number of square feet in an acre. Our Area Calculator does the square-footage step for rectangles, triangles, and circles. The calculator accepts plots from 0.1 to 100 acres.
      2. Pick what you are planting. Four choices cover most deer plots: ladino white clover, a perennial legume; brassicas such as turnips, rape, and radish; cereal grains such as oats, wheat, and rye; and a cool-season blend of grains and clovers. The species sets the seeding rate and the fertilizer blend, because clover and grains feed very differently.
      3. Pick how you are seeding. Broadcasting spreads seed on the surface and needs a higher rate, because some seed never makes good soil contact. Drilling places seed at a set depth with better contact, so it needs less seed for the same stand. The blend recipe is a broadcast recipe either way, because the clover in it must stay within 1/2 inch of the surface.
      4. Enter your soil pH if you know it. The number comes from a soil test, and it sets the lime rate. Leave it blank if you have not tested: the calculator falls back to a rule-of-thumb lime figure and tells you plainly that it is an estimate, not a recommendation.
      5. Enter your prices if you want the cost. Seed price per pound, fertilizer price per 50 lb bag, and lime price per ton are all optional. Enter the prices your dealer quotes and the calculator prices the seed, the fertilizer, the lime, and the total. Leave any of them blank and that cost is left out of the total, with a note saying so. This tool stores no prices, because seed, fertilizer, and lime prices vary by dealer and season, and a stored price would be stale within weeks.

      The result shows your seed pounds, your fertilizer pounds and bag count, your lime tons and bag count, and your total cost, with every number worked out step by step below it. The guidance underneath explains why the tool picked the blend it picked, what your pH means for lime, and what to do next. Warnings flag the traps: very acidic soil, a missing soil test, clover on ground too acidic for it to fix nitrogen, and a plot small enough for deer to eat to the ground.

      Try the example buttons under the form to see the four main cases: one acre of clover on moderately acidic ground, two and a half acres of drilled cereal grains, half an acre of brassicas with no soil test, and three acres of the cool-season blend. Each one fills the form in and runs the calculation, so you can see how the numbers move when the inputs change.

      How the calculator works

      The calculator multiplies a published per-acre rate by your acres, then converts the result into the units you actually buy: pounds of seed, 50 lb bags of fertilizer, tons of lime, and 50 lb bags of lime. Every rate comes from a land-grant extension guide or a seed-company rate sheet, and every rate is named in the tables below so you can check it against your own sources. Nothing here is a guess, and nothing is presented as more precise than it is: the lime figures in particular are planning estimates, because the exact lime rate for your ground comes from your soil test's buffer pH, a measurement no online calculator can take for you.

      Seed comes first. The seeding rates are the broadcast and drilled rates from Mississippi State University Extension publication M1591, "Deer Food Plot Planting Guide for the Southeast", which lists drill and broadcast rates side by side for every common food plot forage. Cereal grains are published as a range, 120 to 150 lb per acre broadcast and 90 to 100 lb drilled, because seed size varies by variety; the calculator uses the midpoints, 135 lb broadcast and 95 lb drilled, and says so. The blend is the cool-season recipe published by the Mississippi Department of Wildlife, Fisheries, and Parks (MDWFP): oats, wheat, crimson clover, and arrowleaf clover at the midpoints of their published ranges. Where sources disagree, the extension table governs: for example, some guides list ladino white clover at 4 to 6 lb per acre broadcast, but M1591 lists 8 lb, and 8 lb is the rate the calculator uses. Your seed bag's printed rate still governs for the seed you actually buy, because germination and seed size vary by lot.

      SpeciesBroadcast (lb per acre)Drilled (lb per acre)Source
      Ladino white clover84MSU Extension M1591
      Red clover1510MSU Extension M1591
      Crimson clover2515MSU Extension M1591
      Brassicas (rape, kale, turnip)105MSU Extension M1591
      Oats, wheat, rye, triticale120 to 150 (tool uses 135)90 to 100 (tool uses 95)MSU Extension M1591
      Cool-season blend (oats, wheat, crimson and arrowleaf clover)70.5 in total70.5 in total (broadcast recipe)MDWFP cool-season recipe

      Fertilizer comes second, and the blend depends on the species. Clover is a legume: once its root nodules form, rhizobium bacteria fix nitrogen from the air, so clover needs phosphorus and potassium but no nitrogen. The calculator gives clover 0-20-20, a blend with no nitrogen, at 250 lb per acre. Brassicas, cereal grains, and the blend all need nitrogen, so they get 19-19-19, a balanced blend, at 300 lb per acre. Both rates are no-test planning rates, the rates extension-cited guides and seed-company sheets quote when no soil test exists. A soil test replaces them with exact rates for your ground, and that is always the better answer.

      PlotBlendRate (lb per acre)What it delivers per acre
      Clover (legume)0-20-202500 lb N, 50 lb P2O5, 50 lb K2O
      Brassicas19-19-1930057 lb N, 57 lb P2O5, 57 lb K2O
      Cereal grains19-19-1930057 lb N, 57 lb P2O5, 57 lb K2O
      Cool-season blend19-19-1930057 lb N, 57 lb P2O5, 57 lb K2O

      Lime comes third, and it is set by your soil pH. The target is pH 6.5, the level where clover, brassicas, and cereal grains can all use the nutrients you apply. The bands below are the published planning rates for agricultural lime on mineral soil, targeting 6.5. Sandy soils need a little less lime to move the same distance, heavy clay needs a little more, and your soil test report gives the exact figure for your ground. With no soil test at all, the calculator uses the MDWFP rule of thumb: 2 tons per acre every third year.

      Current soil pHLime per acreNotes
      Below 5.03.5 tonsVery acidic. Lime now, retest in 6 months.
      5.0 to 5.42.5 tonsStrongly acidic.
      5.5 to 5.91.5 tonsMost untouched plots land here.
      6.0 to 6.40.75 tonsClose. A light application finishes the job.
      6.5 and upNoneAlready in the target range.
      No soil test2 tonsMDWFP rule of thumb, every third year.

      Cost is the last step, and it is computed from the rounded quantities the calculator shows you, so every printed equation balances on the printed numbers. Seed cost is seed pounds times your price per pound. Fertilizer cost is bag count times your price per 50 lb bag, and the bag count always rounds up, because you cannot buy part of a bag. Lime cost is lime tons times your price per ton. The total is the sum of the costs you priced. If you leave a price blank, that cost is left out and a note says so, so the total never pretends to be complete when it is not.

      Worked examples

      Example 1: one acre of clover, broadcast, pH 5.8. Seed: 1 acre times 8 lb per acre is 8 lb of ladino white clover. Fertilizer: 1 acre times 250 lb per acre of 0-20-20 is 250 lb, or 5 bags of 50 lb. Lime: pH 5.8 falls in the 5.5 to 5.9 band, 1.5 tons per acre, so 1.5 tons, or 60 bags of 50 lb. At $6.00 per lb of seed, $25.00 per bag of fertilizer, and $50.00 per ton of lime, the costs are $48.00 for seed, $125.00 for fertilizer, and $75.00 for lime, a total of $248.00.

      Example 2: two and a half acres of cereal grains, drilled, pH 6.2. Seed: 2.5 acres times 95 lb per acre drilled is 237.5 lb. Fertilizer: 2.5 acres times 300 lb per acre of 19-19-19 is 750 lb, or 15 bags. Lime: pH 6.2 falls in the 6.0 to 6.4 band, 0.75 tons per acre, so 2.5 times 0.75 is 1.88 tons (1.875 rounded to two decimals), or 76 bags of 50 lb, because 1.88 tons times 40 bags per ton is 75.2, and part of a bag still means buying the bag. At $0.60 per lb of seed, $28.00 per bag of fertilizer, and $45.00 per ton of lime, the costs are $142.50 for seed, $420.00 for fertilizer, and $84.60 for lime, a total of $647.10.

      Example 3: half an acre of brassicas, broadcast, no soil test. Seed: 0.5 acres times 10 lb per acre is 5 lb. Fertilizer: 0.5 acres times 300 lb per acre of 19-19-19 is 150 lb, or 3 bags. Lime: with no soil test, the rule of thumb is 2 tons per acre, so 0.5 times 2 is 1 ton, or 40 bags of 50 lb, flagged as an estimate until a soil test says otherwise. At $4.00 per lb of seed, $30.00 per bag of fertilizer, and $60.00 per ton of lime, the costs are $20.00 for seed, $90.00 for fertilizer, and $60.00 for lime, a total of $170.00.

      Example 4: three acres of cool-season blend, broadcast, pH 5.2. Seed: the blend runs 70.5 lb per acre, split into oats 27.5 lb, wheat 27.5 lb, crimson clover 11 lb, and arrowleaf clover 4.5 lb. Over 3 acres that is oats 82.5 lb, wheat 82.5 lb, crimson clover 33 lb, and arrowleaf clover 13.5 lb, 211.5 lb in total. Fertilizer: 3 acres times 300 lb per acre of 19-19-19 is 900 lb, or 18 bags. Lime: pH 5.2 falls in the 5.0 to 5.4 band, 2.5 tons per acre, so 7.5 tons, or 300 bags of 50 lb. At $1.10 per lb of seed, $26.00 per bag of fertilizer, and $40.00 per ton of lime, the costs are $232.65 for seed, $468.00 for fertilizer, and $300.00 for lime, a total of $1,000.65.

      Seeding rates by species

      Seeding rate is where good plots go wrong, and it is the single biggest reason first-time plotters over- or under-buy seed. The range across common plot species is enormous: a pure clover stand might go down at 6 to 12 lb per acre, while cereal grains go down at 120 to 150 lb per acre. The difference is seed size. A pound of clover seed holds hundreds of thousands of tiny seeds; a pound of oats holds a few thousand large ones. Judging seed by the bag instead of by the species is how people end up with a thin clover stand or a choked oat field.

      Clover: the perennial workhorse

      Ladino white clover is the classic deer plot perennial. It is high in protein, it tolerates heavy browsing, and a well-kept stand lasts four to five years in northern country, two to three in the South. Mississippi State Extension lists ladino at 8 lb per acre broadcast and 4 lb drilled. Red clover runs heavier, 15 lb broadcast and 10 lb drilled, because its seed is larger and it grows taller. Crimson clover, an annual that establishes fast and carries a plot into spring, runs 25 lb broadcast and 15 lb drilled. The calculator uses ladino as its clover, because ladino is the perennial most plotters mean when they say clover, and the other clovers are covered in the table above so you can scale the numbers yourself. Clover seed is small and must sit almost on the surface: plant it no deeper than 1/4 inch, and never disk it in. Bury clover seed an inch deep and most of it never emerges, because the seedling carries too little stored energy to push through that much soil.

      One detail first-time clover growers miss is inoculation. Clover fixes nitrogen only through rhizobium bacteria living in nodules on its roots, and the bacteria must be present in the soil or on the seed. Buy pre-inoculated seed, or inoculate within 24 hours of planting with the right strain for your clover type, keep the inoculant refrigerated until use, and plant into moist soil. Rhizobium dies fast in heat and on dry seed, and dead inoculant means a clover stand that cannot feed itself nitrogen. Inoculant codes vary by manufacturer, so the code on your seed bag or inoculant packet governs, not any chart.

      Brassicas: the late-season closer

      Brassicas, turnips, rape, kale, and forage radish, are the late-season plot. Deer often ignore them until the first frosts turn their starches to sugars, then hammer the leaves and dig the bulbs through the winter. Mississippi State Extension lists the brassica group at 10 lb per acre broadcast and 5 lb drilled. That is a group rate: straight purple-top turnips alone run 4 to 6 lb per acre broadcast, and forage radish runs 8 to 12 lb, so a single-species turnip plot needs less seed than the group rate suggests. In a blend, cut the brassica rate further, to 2 to 3 lb per acre, because the brassicas share the ground with grains and clovers and will crowd them out at full rate. Brassicas are heavy nitrogen feeders, which is why the calculator pairs them with 19-19-19 and suggests a nitrogen topdress later. Plant brassicas 60 to 90 days before your average first killing frost, late July through early September across most of the whitetail's range, so the plants have time to build leaf and bulb before the cold. Seed depth is 1/4 to 1/2 inch at most.

      Cereal grains: fast, cheap, and forgiving

      Oats, winter wheat, cereal rye, and triticale are the workhorses that make a plot look good fast. They germinate in days, tolerate a rough seedbed, and feed deer from fall through spring. Mississippi State Extension lists all four at 120 to 150 lb per acre broadcast and 90 to 100 lb drilled. The calculator uses the midpoints, 135 lb broadcast and 95 lb drilled, because the range exists to cover variety differences in seed size, and the midpoint is the honest planning figure for a plotter who has not yet picked a variety. If your seed bag prints a rate, use the bag's rate: it reflects the seed size of that specific lot. Oats are the most palatable of the group and the first deer eat; wheat is a close second and stands up better to cold; cereal rye is the toughest of all, growing on poor ground and in cold that kills oats, though deer prefer it young. Planting depth is 1/2 to 1 inch, deeper than clover or brassicas, which is why grains are often drilled or lightly disked in after broadcasting while small seed is cultipacked on top.

      The cool-season blend: forage from October to June

      The blend in this calculator is the cool-season mixture published by MDWFP: oats, wheat, crimson clover, and arrowleaf clover, broadcast together. The idea is staggered maturity. Oats and wheat germinate fast and feed deer through hunting season. Crimson clover grows slowly until late winter, then grows fast and blooms in late March to mid-April. Arrowleaf clover takes over from there and matures from mid-June to early July. One planting feeds deer from October through June, and the mix hedges against total failure, because insects, disease, or weather that hits one species rarely hits them all. The recipe is oats 25 to 30 lb per acre, wheat 25 to 30 lb, crimson clover 10 to 12 lb, and arrowleaf clover 4 to 5 lb; the calculator uses the midpoints, 27.5, 27.5, 11, and 4.5, for a total of 70.5 lb per acre, and shows each component separately so you can buy each seed by the pound. Plant the mix no deeper than 1/2 inch, because the clover component must stay near the surface, and cultipack after seeding to press the small seed into contact with the soil.

      Broadcast or drill: why the rate changes

      Drilled rates run roughly half the broadcast rate for small seed and about two-thirds for grains, because drilling puts every seed at a set depth with firm soil contact, while broadcast seed lands where it lands and some of it never germinates. That is why the calculator asks how you are seeding: the same acre of clover needs 8 lb broadcast but only 4 lb drilled, and the same acre of oats needs 135 lb broadcast but 95 lb drilled. If you broadcast, a cultipacker pass afterward closes much of the gap by pressing seed into the soil, and it is the cheapest stand improvement a broadcaster can buy. If you drill, check the depth setting for the smallest seed in the mix: a drill set for oats will bury clover too deep.

      Pure live seed: the number on the tag that changes your order

      Extension seeding rates are published on a pure live seed (PLS) basis, which means pounds of seed that is both pure and alive. Your seed tag lists two percentages, purity and germination, and PLS is purity times germination divided by 100. A tag reading 90% purity and 80% germination is 72% PLS: only 72% of every pound you buy is live seed of the species you want. To match the calculator's pounds, divide by the PLS fraction. For 8 lb of clover at 72% PLS, buy 8 divided by 0.72, about 11.1 lb of bulk seed. Cheap seed with a low PLS reading is often no bargain once the adjustment is made, and it is the quiet reason some plots come up thin even when the planter followed the rate chart exactly.

      Fertilizer: why clover gets a different blend

      The three numbers on a fertilizer bag are percentages of nitrogen (N), available phosphate (P2O5), and soluble potash (K2O), in that order. A bag of 19-19-19 is 19% nitrogen, 19% phosphate, and 19% potash, so 300 lb of it delivers 57 lb of each nutrient per acre. A bag of 0-20-20 is 0% nitrogen, 20% phosphate, and 20% potash, so 250 lb of it delivers no nitrogen, 50 lb of phosphate, and 50 lb of potash per acre. The numbers on the bag are the whole story of what you are buying, and comparing blends by price per bag without comparing the numbers is how plotters pay more for less nutrition.

      Clover gets the no-nitrogen blend because it makes its own. Once rhizobium bacteria colonize its root nodules, clover fixes nitrogen from the air, and it needs little to no nitrogen fertilizer after the seedling stage. Feeding clover nitrogen does not help it: it feeds the weed grasses competing with it, and heavy nitrogen at planting can discourage the plant from forming the nodules it needs to fix nitrogen later. What clover does need is phosphorus and potassium, which build roots and keep the stand productive for years. That is why the calculator gives clover 0-20-20 at 250 lb per acre, the midpoint of the published 200 to 300 lb range for legumes, and why it tells you to topdress phosphorus and potassium each year and skip the nitrogen.

      Brassicas and cereal grains are the opposite case. They fix no nitrogen, and nitrogen is what drives their leaf growth and tonnage. The calculator gives them 19-19-19 at 300 lb per acre, the standard no-test planning rate quoted across extension-cited guides and seed-company sheets, including Pennington's published no-test fallback of 300 lb per acre of 19-19-19 with 1 ton of lime per acre. The blend gets the same balanced blend, because its grain component needs nitrogen even though its clover component does not, and the grains set the blend's nitrogen demand.

      Both fertilizer rates are planning rates for ground with no recent soil test. A soil test can change them in either direction: ground that has been fertilized for years may already hold enough phosphorus and potassium to need far less, and ground that has never been fertilized may need more. The test report usually reads as pounds of actual nutrient per acre, such as 60 lb of nitrogen, 40 lb of P2O5, and 40 lb of K2O, and you convert that to bag rate by dividing by the percentage on the bag. If your report says 40 lb of P2O5 and zero nitrogen for a clover plot, 0-20-20 at 200 lb per acre delivers exactly that, and 19-19-19 would waste its nitrogen. Your lab's recommendation governs over any general rate, including the ones in this calculator.

      Timing matters as much as rate. Apply the base fertilizer at or just before planting, worked into the seedbed so it sits where the roots will find it. Brassicas and cereal grains then benefit from a nitrogen topdress once they are established: 30 to 50 lb of actual nitrogen per acre, 30 to 45 days after emergence for brassicas, or at spring green-up for cereal grains. Pennington's brassica sheet puts the topdress at 100 to 150 lb per acre of 34-0-0, which delivers 34 to 51 lb of actual nitrogen. Do not topdress clover with nitrogen. And never treat fertilizer as a substitute for lime: on acidic ground the phosphorus you apply binds to the soil and stays unavailable to the plant, which is why the lime section below comes before the fertilizer goes down.

      Lime and soil pH: the step most plotters skip

      Soil pH runs from 1 to 14, with 7 neutral, below 7 acidic, and above 7 alkaline. Most food plot ground that has never been limed sits moderately acidic, usually around pH 5.0 to 5.5 in the humid Southeast, and most food plot species want pH 6.0 to 7.0 to use the nutrients in the soil. MDWFP puts the target at 6.7 to 7.0 for maximum productivity, especially on legumes, and this calculator targets 6.5, the level where clover, brassicas, and cereal grains all perform well. Below pH 6.0, phosphorus availability drops sharply even when a soil test shows adequate phosphorus present, and below pH 5.5 clover yields fall hard because the rhizobium bacteria in its root nodules lose efficiency in acidic soil.

      The cost of skipping lime is measurable. MDWFP's guide states that at a soil pH around 4.5, close to 80% of the money spent on fertilizer is wasted, because the nutrients stay locked up where roots cannot reach them. Lime is usually the bigger lever than fertilizer, and it is the one people skip, because it is bulky, unglamorous, and slow. Agricultural lime takes 6 to 12 months to fully react with the soil, longer if it is not tilled in, which is why the right time to lime is months before planting, ideally disked in at least 3 months ahead. Lime applied the week before seeding helps the following season more than the current one.

      How much lime a plot needs depends on two things: how far the pH must move, and how strongly the soil resists moving. Clay soils need more lime than sandy soils to move the same distance, because clay buffers pH changes; raising pH one full point on clay soil can take 1 to 2 tons of lime per acre. Your soil test measures this resistance as buffer pH, and the lab's lime recommendation is built on it. That is why the calculator's lime bands are planning estimates, and why the tool pushes you toward a soil test in every result. A test through a land-grant extension lab usually costs $10 to $25, and it returns your pH, your phosphorus and potassium levels, and a lime and fertilizer recommendation matched to the crop you tell the lab you are planting. Tell the lab what you are growing, because a soybean recommendation and a brassica recommendation are not the same numbers. Retest every 2 to 3 years once fertility is established, and more often in the first seasons while you are building up low-fertility ground.

      The lime bands in this calculator run from 3.5 tons per acre below pH 5.0 down to none at pH 6.5 and above, and they sit inside the 1 to 3 tons per acre range that extension guidance commonly quotes for moderately acidic food plot soils. Very acidic ground below pH 5.0 can need 3 to 4 tons. With no soil test, the calculator uses the MDWFP rule of thumb, 2 tons per acre every third year, and labels it an estimate. Do not be surprised if a real soil test comes back recommending 3 tons per acre on ground that has never been limed: that is normal, not a mistake.

      Lime comes in two forms, and the choice is practical. Powdered agricultural lime is the cheapest per ton and the form a spreader truck applies, but the truck must be able to reach the plot. Pelletized lime comes in 50 lb bags, costs far more per ton, and spreads through a broadcast seeder or ATV attachment, which makes it the choice for small or remote plots. The calculator shows both tons and 50 lb bag counts, so a small plot can be priced in bags and a large one in tons. One ton of lime is 40 bags of 50 lb. Do not over-lime: pushing pH above 7.0 to 7.5 locks up micronutrients such as zinc, manganese, and iron, and causes more harm than staying slightly acidic at 5.8 to 6.0. If your pH is already above 7.0, the calculator gives you no lime at all, and warns you against adding any.

      Features

      Four species, two seeding methods. Clover, brassicas, cereal grains, and a cool-season blend, each with broadcast and drilled rates from Mississippi State Extension. The blend shows every component separately, so you can price oats, wheat, and each clover on its own.

      The right fertilizer blend for the species. Legumes get a no-nitrogen blend, because they fix their own. Grains and brassicas get a balanced blend, because they need nitrogen. The calculator explains the choice in plain language every time, so the blend is never a mystery number.

      Lime by soil pH band, with an honest unknown. Enter your pH and the lime rate follows the published bands. Leave it blank and the calculator uses the MDWFP rule of thumb, labels it an estimate, and tells you to test before you buy. It never presents a guessed lime rate as a recommendation.

      Costs at your prices, or no cost at all. Seed, fertilizer, and lime prices are yours to enter, and any one of them can be left blank. The total covers only what you priced, and the steps name anything left out, so a partial total is never mistaken for a complete one.

      Bag counts that match how you buy. Fertilizer is priced and counted in 50 lb bags, rounded up, because dealers sell bags, not pounds. Lime shows tons for spreader-truck jobs and 50 lb bag counts for pelletized lime on small or remote plots.

      Warnings that catch the expensive mistakes. Very acidic soil, a missing soil test, clover on ground too acidic to fix nitrogen, alkaline soil that needs no lime, and a plot small enough for deer to eat to the ground all get flagged before you spend anything.

      Every number shown working. The steps below the result show each multiplication, so you can check the arithmetic against your own figures, and the printed equations always balance on the printed numbers.

      Use cases

      First food plot on new ground. You just bought or leased land and have never tested the soil. Enter your acres and species, leave the pH blank, and the calculator gives you seed and fertilizer plus a rule-of-thumb lime figure, with a clear push to test before you buy lime. Use the result as a shopping list and a budget, then let the soil test refine the lime and fertilizer before you spread anything.

      Annual clover maintenance. Your ladino stand is in its second or third year and needs its yearly feed. Run the calculator for your clover acres with your current pH, and it gives you the 0-20-20 topdress and any lime the pH still calls for. No nitrogen, because the stand fixes its own.

      Late-season brassica plot. You want turnips and radish drawing deer after the first frost. The calculator gives you the brassica seed rate, the 19-19-19 base rate, and the lime to get the pH toward 6.5, plus the nitrogen topdress note for a month after emergence.

      Comparing plots before you commit. Run the same acres through clover, brassicas, grains, and the blend, and compare seed pounds, fertilizer, lime, and total cost side by side. Clover costs more per pound of seed but lasts years; grains cost more seed per acre but establish fast; the blend spreads risk across species. The numbers make the trade-off concrete.

      Budgeting a whole property. A hunting club or a landowner with several plots can run each plot separately, add the totals, and walk into the feed store with exact quantities instead of a guess. Pair the result with our Deer Carrying Capacity Calculator to check how many deer the land can support, and our Hunting Land Cost Calculator to price the ground itself. For season planning, our Deer Rut Timing Calculator pins down the peak breeding window, and our Deer Weight and Yield Estimator turns a harvested deer into dressed weight and venison. If you lease ground, our Hunting Lease Cost Calculator prices the lease, and our Big Game Processing Cost Calculator prices what happens after the shot.

      What a food plot costs

      Food plot costs split three ways, and the split surprises first-time plotters. Seed is usually the smallest line for grains and the largest for clover, because clover seed costs far more per pound even though you use far fewer pounds. Fertilizer is usually the largest line for grains and brassicas, because 300 lb per acre at 50 lb a bag adds up fast. Lime is the line people forget, and on acidic ground it can match the fertilizer bill, especially in pelletized bags, which cost several times more per ton than bulk lime spread by truck.

      The worked examples above show the shape of it. One acre of clover at the example prices runs $248.00 in total: $48.00 of seed, $125.00 of fertilizer, and $75.00 of lime. Two and a half acres of drilled cereal grains runs $647.10: $142.50 of seed, $420.00 of fertilizer, and $84.60 of lime. Half an acre of brassicas runs $170.00. Three acres of the blend runs $1,000.65, most of it fertilizer and lime. Those are example prices, not market prices, and they exclude equipment, fuel, herbicide, and your time. What they show is the structure: on most plots, fertilizer and lime together cost more than seed, and lime is the difference between fertilizer that feeds plants and fertilizer that feeds the soil chemistry.

      Three things cut the bill without cutting the plot. First, test the soil: ground that has been fertilized for years often needs far less phosphorus and potassium than the planning rate, and the test can cut the fertilizer order in half. Second, lime early and in bulk: bulk lime spread by truck costs a fraction of pelletized lime per ton, and lime applied a season ahead works better than lime applied at planting. Third, keep a perennial clover stand going instead of replanting annuals every year: the seed cost spreads over four to five years, and the stand fixes its own nitrogen the whole time.

      Sources

      • Mississippi State University Extension, M1591, "Deer Food Plot Planting Guide for the Southeast". Cool- and warm-season forage planting rates, drill and broadcast columns, planting dates, and inoculant strains. Broadcast rates used in this calculator: ladino white clover 8 lb per acre, red clover 15 lb, crimson clover 25 lb, brassicas 10 lb, oats, wheat, rye, and triticale 120 to 150 lb; drilled rates: ladino 4 lb, red clover 10 lb, crimson clover 15 lb, brassicas 5 lb, grains 90 to 100 lb. Planting windows: small grains August 15 to October 15, brassicas and clovers September 1 to October 15. Deer Food Plot Planting Guide for the Southeast.
      • Mississippi Department of Wildlife, Fisheries, and Parks, "Cool Season Food Plots". Target soil pH 6.7 to 7.0 for maximum productivity; about 80% of fertilizer money wasted at pH 4.5; lime rule of thumb 2 tons per acre every third year without a soil test; 3 tons per acre common on never-limed sites; legumes fix their own nitrogen and need no nitrogen in the fertilizer mixture; plots of at least one acre recommended; cool-season blend recipe of oats 25 to 30 lb, wheat 25 to 30 lb, crimson clover 10 to 12 lb, and arrowleaf clover 4 to 5 lb per acre. Verified live 20 November 2026. Cool Season Food Plots.
      • Pennington Seed, Rackmaster planting instructions (seed-company rate sheets, as published by retailers). Brassica mix: 300 lb per acre of 19-19-19 in the absence of a soil test, plus 1 ton per acre of lime, with a nitrogen topdress of 100 to 150 lb per acre of 34-0-0 (30 to 50 lb of actual nitrogen) 30 to 45 days after emergence. Mississippi Complete mix: 100 lb per acre seeding rate, 400 lb per acre of 10-10-10, 1 ton per acre of lime. Rackmaster How to Plant Great Food Plots. Pennington Rackmaster Mississippi Complete Food Plot Seed Mix.
      • University of Tennessee Extension, food plot and forage brassica guides (PB1874 and SP731-C), as cited by secondary sources. Brassicas planted 60 to 90 days before the first killing frost; turnip and brassica seeding guidance; soil testing as the only way to know actual phosphorus and potassium levels. The UT publication itself was not directly accessible on the day of building; its figures are used here only where secondary sources quoting it agree with the Mississippi State table, and the Mississippi State table governs every rate in the calculator.
      • Penn State Extension, liming and soil-testing guidance, as cited by secondary sources. Lime applied on the basis of the soil test's lime requirement value, because generic rates can under- or over-correct depending on soil buffering capacity; typical ag lime rates of 1 to 2 tons per acre to move pH from 5.5 to 6.5 on clay loam; pure live seed formula, PLS percent equals purity percent times germination percent divided by 100.
      • Food Plot Calculator, "How to Read a Soil Test for Food Plots" and "Food Plot Fertilizer Calculator". Lime planning bands targeting pH 6.5 (below 5.0: 3 to 4 tons; 5.0 to 5.4: about 2.5 tons; 5.5 to 5.9: about 1.5 tons; 6.0 to 6.4: about 0.75 tons), fertilizer blend table (19-19-19 at 300 lb per acre standard; 0-20-20 at 250 lb per acre for pure legume plots), lime reaction time 6 to 12 months. Secondary source, cross-checked against extension guidance. How to Read a Soil Test for Food Plots. Food Plot Fertilizer Calculator.
      • PlotSeason, "How Much Fertilizer for Deer Food Plots", "How to Fertilize a Food Plot", and "Fertilizer for Food Plots". No-test fertilizer ranges (19-19-19 at 300 to 400 lb per acre for annual grain and brassica plots; 0-20-20 at 200 to 300 lb per acre for legumes); soil test cost typically $10 to $25 through land-grant extension labs; retesting every 2 to 3 years once fertility is established; lime reaction time 3 to 6 months to a year. Secondary source, citing Mississippi State Extension, University of Tennessee Extension, and Penn State Extension. How Much Fertilizer for Deer Food Plots.

      Figures in this article were verified against the sources above on 20 November 2026. Where sources disagree, the Mississippi State Extension table governs seeding rates, the MDWFP guide governs the blend recipe and the no-test lime rule of thumb, and the seed bag governs for the seed actually purchased. The cereal grain rate (135 lb broadcast, 95 lb drilled) and the blend component rates (oats 27.5, wheat 27.5, crimson clover 11, arrowleaf clover 4.5 lb per acre) are midpoints of published ranges, stated as such. The 0-20-20 rate (250 lb per acre) is the midpoint of the published 200 to 300 lb range for legumes. Lime bands are planning estimates for mineral soil targeting pH 6.5; sandy soils need less, clay soils need more, and the soil test's buffer pH sets the exact rate.

      Frequently asked questions

      How much clover seed do I need per acre?

      For ladino white clover, Mississippi State Extension lists 8 lb per acre broadcast and 4 lb drilled. Red clover runs heavier at 15 lb broadcast and 10 lb drilled, and crimson clover at 25 lb broadcast and 15 lb drilled, because the seed is larger. Some guides list ladino as low as 4 to 6 lb broadcast, but the Mississippi State table governs here, and your seed bag's printed rate governs for the seed you actually buy. Clover seed must sit almost on the surface, no deeper than 1/4 inch, and it must be inoculated with the right rhizobium strain or it cannot fix nitrogen.

      How much fertilizer does a food plot need?

      Without a soil test, the standard planning rate is 300 lb per acre of 19-19-19 for brassicas, cereal grains, and blends, and 250 lb per acre of 0-20-20 for clover. The 19-19-19 rate is the no-test fallback published on Pennington's seed-company sheets and quoted across extension-cited guides, and the 0-20-20 rate is the midpoint of the published 200 to 300 lb range for legumes. A soil test replaces both with exact rates for your ground, and it often cuts the fertilizer bill, because ground that has been fertilized for years may already hold enough phosphorus and potassium.

      Why does clover get 0-20-20 instead of 19-19-19?

      Because clover makes its own nitrogen. Once rhizobium bacteria colonize its root nodules, clover fixes nitrogen from the air, so it needs phosphorus and potassium but no nitrogen from a bag. Feeding clover nitrogen does not help it: it feeds the weed grasses competing with it, and heavy nitrogen at planting can discourage the plant from forming the nodules it needs. The 0 in 0-20-20 means zero nitrogen, and the 20-20 means 20% phosphate and 20% potash. Brassicas and cereal grains fix no nitrogen, so they get the balanced 19-19-19 blend instead.

      How much lime does a food plot need?

      It depends on your soil pH. Targeting pH 6.5 on mineral soil, the planning bands are 3.5 tons per acre below pH 5.0, 2.5 tons at pH 5.0 to 5.4, 1.5 tons at pH 5.5 to 5.9, 0.75 tons at pH 6.0 to 6.4, and none at pH 6.5 and above. With no soil test, the MDWFP rule of thumb is 2 tons per acre every third year. Sandy soils need less lime and clay soils need more to move the same distance, and your soil test's buffer pH sets the exact rate. Lime takes 6 to 12 months to fully react, so apply it months before planting, ideally disked in at least 3 months ahead.

      Should I broadcast or drill my food plot seed?

      Drilling needs less seed and gives a more even stand, because every seed lands at a set depth with firm soil contact. Broadcasting needs a higher rate, roughly double for small seed like clover and about 40% more for grains, because some broadcast seed never makes good contact. If you broadcast, a cultipacker pass afterward presses the seed into the soil and closes much of the gap. Small seed must stay shallow either way: clover no deeper than 1/4 inch, brassicas 1/4 to 1/2 inch, and the clover in a blend within 1/2 inch of the surface. Grains go deeper, 1/2 to 1 inch.

      How much does a food plot cost per acre?

      It depends on the species, the soil, and your dealer's prices, which is why this calculator asks for your prices instead of storing any. As a worked example, one acre of clover at $6.00 per lb of seed, $25.00 per 50 lb bag of fertilizer, and $50.00 per ton of lime runs $248.00 in total: $48.00 of seed, $125.00 of fertilizer, and $75.00 of lime. Fertilizer and lime together usually cost more than seed, and lime is the line people forget. A soil test is the best way to cut the bill, because it often shows the ground needs less fertilizer than the planning rate.

      What is pure live seed, and why does it change how much seed I buy?

      Pure live seed (PLS) is the share of a bag that is both pure seed of the species you want and alive enough to germinate. It equals purity percent times germination percent divided by 100, and both percentages are printed on the seed tag. A tag reading 90% purity and 80% germination is 72% PLS, so only 72% of every pound you buy is live seed. Extension seeding rates are published on a PLS basis, so divide the calculator's pounds by the PLS fraction to get the bulk pounds to buy: 8 lb of clover at 72% PLS means buying about 11.1 lb of bulk seed.

      When should I plant a deer food plot?

      Cool-season plots go in during late summer and fall. Mississippi State Extension lists August 15 to October 15 for small grains (oats, wheat, rye) and September 1 to October 15 for brassicas, chicory, and clovers in the Southeast; northern planters shift earlier. Brassicas need 60 to 90 days before the average first killing frost to build leaf and bulb, so late July through early September across most of the whitetail's range. Clover can also go in during early spring. Lime goes down months before any of it, because it takes 6 to 12 months to fully react, so soil testing and liming in spring for a fall planting is the right order.