What Size Mini Split Do I Need?
Recommended mini split size
9,000 BTU
How the number is built up
Last reviewed: 19 November 2026. Reviewed every 180 days; next review due 18 May 2027.
How to use the Mini Split BTU Sizer
A mini split that is too small runs flat out on the hottest afternoon and still cannot keep up. One that is too big cools the room fast, shuts off, and leaves the air damp and clammy. The right size comes from your room's square footage plus a handful of published adjustments for sun, people, kitchens, ceilings, insulation, and climate, and this sizer applies them all and rounds the result to a real mini split head size. It takes less than a minute.
- Measure your room. Measure the longest wall and the wall next to it, in feet, and enter both numbers. For an open floor plan, measure the whole connected space, kitchen and living room together, not just the seating area. If you are measuring the room anyway, our Rug Size Finder uses the same dimensions to size a rug for the space.
- Enter your ceiling height. Most rooms have 8-foot ceilings, which is the default. If your ceiling is taller, enter the real height: a taller ceiling holds more air, and the unit has to cool a bigger volume.
- Pick the room type. Choose living room, bedroom, or kitchen. A kitchen adds 4,000 BTU for cooking heat, per ENERGY STAR, which is often the largest single adjustment on the list.
- Pick sun exposure, insulation, and climate. A very sunny room adds 10 percent; a heavily shaded room takes 10 percent off. Poor insulation adds 20 percent; good insulation takes 10 percent off. A hot climate adds 15 percent; a cold climate takes 10 percent off the cooling load. The insulation and climate factors are this tool's own planning factors, stated openly in the how-it-works section below, because published sources disagree on them.
- Enter the regular occupants. ENERGY STAR adds 600 BTU for each regular occupant beyond two. Count the people who use the room most days, not the occasional guest.
- Read your result. You get the recommended head size in BTU and tons, the estimated cooling load behind it, an ENERGY STAR chart cross-check, the full adjustment breakdown, and plain-language guidance, including a heating warning for cold climates and a multi-zone warning when the load passes the largest single head.
This sizer is one of the free tools on Tools Elite. Every rule and every figure on this page comes from a published source listed at the bottom, and the sizer shows its work: the room area, each adjustment, and the rounding to a standard size are all in the result. Mini split sizing is an estimate, not a substitute for a professional load calculation, so treat the recommendation as the size to shop with and confirm it with a Manual J calculation before you buy.
How it works
The sizer works in five steps: it measures your room, it applies the 20 BTU per square foot baseline, it adjusts for ceiling height, sun, insulation, and climate, it adds the flat ENERGY STAR allowances for a kitchen and extra occupants, and it rounds up to the next standard mini split size.
Step 1: measure the room. Room area is length times width. A 20 by 25 foot living room is 500 square feet. For an L-shaped room, measure each rectangle separately, add the areas together, then enter a length and width that multiply to that total.
Step 2: apply the baseline. The long-standing rule of thumb for cooling is about 20 BTU per square foot, used by the U.S. Department of Energy and ENERGY STAR guidance and repeated in every published mini split sizing guide. The base load is the room area times 20. For a 500 square foot room, that is 10,000 BTU. The rule assumes an 8-foot ceiling, average insulation, average sun, and a moderate climate, which is why the next step exists.
Step 3: adjust for the room's conditions. Four multipliers apply in order. The ceiling factor is the ceiling height divided by 8, so a 10-foot ceiling gives 1.25 and a 12-foot ceiling gives 1.5. The sun factor is 0.9 for a heavily shaded room, 1.0 for average sun, and 1.1 for a very sunny room, straight from ENERGY STAR. The insulation factor is 1.2 for poor insulation, 1.0 for average, and 0.9 for good insulation. The climate factor is 1.15 for a hot climate, 1.0 for moderate, and 0.9 for cold. The sun factors are ENERGY STAR's published adjustments. The ceiling ratio, insulation factors, and climate factors are this tool's own planning factors: ENERGY STAR says only that higher ceilings call for higher capacity, without giving a number, and published sources disagree on insulation and climate, so the sizer states its factors here and in the README rather than presenting them as a standard.
Step 4: add the flat allowances. A kitchen adds 4,000 BTU for cooking heat, per ENERGY STAR. Each regular occupant beyond the first two adds 600 BTU of body heat, per ENERGY STAR. A room with one occupant gets no deduction: the baseline already assumes two people, and ENERGY STAR only adds for occupants beyond two.
Step 5: round up to a standard size. Mini splits are sold in fixed sizes: 9,000, 12,000, 18,000, 24,000, and 36,000 BTU. The sizer picks the smallest size at or above the computed load, never below it, because an undersized unit cannot reach the set temperature on the hottest day. If the load passes 36,000 BTU, the sizer says so plainly and recommends a multi-zone system instead of pretending a single head will do.
Worked example. Take a 20 by 25 foot living room with 10-foot ceilings, strong afternoon sun, poor insulation, in a hot climate, used by two people. Area is 20 times 25, which is 500 square feet. Base load is 500 times 20, which is 10,000 BTU. The ceiling factor is 10 divided by 8, which is 1.25, so the load becomes 12,500. Very sunny adds 10 percent, so it becomes 13,750. Poor insulation adds 20 percent, so it becomes 16,500. A hot climate adds 15 percent, so it becomes 18,975 BTU, which is 38 BTU per square foot. No kitchen and no extra occupants, so nothing else is added. The smallest standard size at or above 18,975 is 24,000 BTU, which is 2 tons, and it sits 26 percent above the computed load. The ENERGY STAR chart, before adjustments, gives 12,000 BTU for a 500 square foot room, which shows how much the conditions matter: the same room with average conditions would take a 12,000 BTU head, and this one needs 24,000.
Where the factors disagree. The insulation and climate factors deserve an honest note, because three published mini split calculators give three different answers. NumbrWiz uses 1.30 for poor insulation, 1.15 for average, 1.0 for good, and 0.85 for excellent, with climate factors of 0.90 for mild, 1.0 for moderate, 1.15 for hot, and 1.30 for very hot. An HVAC technician's guide puts poor insulation at plus 20 percent and ceilings above 8 feet at plus 10 to 20 percent, and uses a 20 to 25 BTU per square foot range instead of separate climate factors. A third calculator puts poor insulation at plus 40 percent. This sizer takes the middle of that range: poor insulation 1.20, good insulation 0.90, hot climate 1.15, cold climate 0.90. If your home is a drafty pre-war house with single-pane windows, the honest move is to treat the recommendation as a floor and get a Manual J calculation, because no rule of thumb captures that house well.
What your result means
The estimated load is the number to shop by; the head size is what you buy. The sizer shows both, because they are different numbers and the gap between them matters. A 300 square foot living room has an estimated load of 6,000 BTU, but the smallest standard head is 9,000 BTU, so the recommendation is 50 percent above the load. That is not a mistake: there is no 6,000 BTU single-zone head from most brands, and the inverter compressor in a modern mini split ramps its output down to match a small load instead of cycling on and off. The gap is worth knowing about, though, which is why the result states the oversize percentage plainly.
The ENERGY STAR chart cross-check is your sanity check. ENERGY STAR publishes a banded chart for room air conditioners: 5,000 BTU for 100 to 150 square feet, 6,000 for 150 to 250, 9,000 for 350 to 400, 12,000 for 450 to 550, 18,000 for 700 to 1,000, and so on up to 34,000 for 2,000 to 2,500 square feet. The sizer shows the chart figure for your room beside its own estimate. The two numbers will not match exactly, because the chart is banded and the sizer is continuous, and because the chart figure is before adjustments. On a 500 square foot room the chart says 12,000 and the unadjusted rule says 10,000. On a 300 square foot room the chart says 8,000 and the rule says 6,000. The chart runs higher on small rooms, which is the subject of its own section below. If the two figures ever disagreed wildly, that would be a sign of a data-entry error, not a scientific dispute.
The oversize percentage tells you how much headroom the rounding bought. Mini split sizes are spaced far apart, so the rounding step can add anywhere from nothing to more than double the computed load. A load of exactly 12,000 BTU is a perfect fit. A load of 12,100 BTU rounds up to 18,000, which is 49 percent above the load. That is the nature of fixed sizes, and it is why the result shows the percentage: a 49 percent oversize on a mild-climate bedroom is a reason to ask your installer whether the smaller head would do, while the same oversize on a hot-climate sunroom is headroom you will be glad of in August. Inverter compressors make modest oversizing tolerable, because they modulate down to part load, but they do not make gross oversizing free: a head far above the load still short-cycles on mild days.
The tons figure is the same size in the language contractors use. One ton of cooling equals 12,000 BTU per hour, so a 9,000 BTU head is 0.75 tons, 18,000 is 1.5 tons, 24,000 is 2 tons, and 36,000 is 3 tons. The term comes from the cooling once produced by melting a ton of ice in a day, and it is still how HVAC professionals talk about capacity. When a quote says "2-ton mini split," it means a 24,000 BTU unit.
A beyond-largest result means multi-zone, not a bigger head. If the computed load passes 36,000 BTU, no single head covers the space. The usual answer is a multi-zone system: one outdoor unit feeding a head in each room, each sized to its own room. The U.S. Department of Energy notes that many models support up to four indoor units on one outdoor unit. Size each head separately with this sizer, room by room, and have the installer confirm the outdoor unit can carry them all.
The heating note matters most in cold climates. A mini split is a heat pump: it heats as well as cools, and in a cold climate the heating load can be larger than the cooling load. This sizer sizes for cooling. If you picked a cold climate, the result warns you to check the model's published heating capacity at your winter design temperature, because a unit's heating output falls as it gets colder outside. The cold-climate section below gives the numbers.
Filtration is a separate question. The Department of Energy notes that mini splits generally have lower-rated filters that cannot capture the small particles that affect indoor air quality, and that a separate filtered air cleaner may be necessary if greater filtration is desired. If allergies or smoke are part of why you are conditioning the room, size the air cleaner separately with our Air Purifier Size Calculator, which matches a purifier's smoke CADR to the same room.
Mini split sizes explained
Mini splits come in fixed sizes, and the gaps between them are wide. The table below gives each standard head size, its tonnage, the room it typically serves in a moderate climate with average conditions, and what it is best for. The room ranges come from the ENERGY STAR chart bands adapted to mini split head sizes. A sunny room, a tall ceiling, poor insulation, or a hot climate all shrink the room a given head can serve, which is why the sizer adjusts before it rounds.
| Head size | Tons | Typical room | Best for |
|---|---|---|---|
| 6,000 BTU | 0.5 | 100 to 250 sq ft | Small bedrooms. Sold by some brands only, such as Mitsubishi. |
| 9,000 BTU | 0.75 | 250 to 400 sq ft | Bedrooms, small living rooms, home offices. |
| 12,000 BTU | 1 | 400 to 600 sq ft | Living rooms, large bedrooms, garages, additions. |
| 18,000 BTU | 1.5 | 700 to 1,000 sq ft | Large living rooms, open-plan living and dining areas. |
| 24,000 BTU | 2 | 1,000 to 1,400 sq ft | Very large open spaces, whole small apartments. |
| 36,000 BTU | 3 | 1,500 to 2,000 sq ft | Large open plans. Spaces this size usually suit a multi-zone system better. |
9,000 BTU is the practical starting point. Most single-zone mini splits sold in the United States start at 9,000 BTU, and it is the size this sizer recommends for any load up to 9,000. A 6,000 BTU head exists, Mitsubishi sells one as the MSZ-GL06NA with a 6,000 BTU cooling rating and a 7,200 BTU heating rating, but it is a multi-zone indoor unit, and most DIY single-zone kits start at 9,000. If your computed load is under about 6,500 BTU, the sizer tells you to look for a 6,000 BTU head, because a 9,000 BTU unit on a 2,400 BTU load is nearly four times the size the room needs.
12,000 BTU is the workhorse size. One ton covers the 400 to 600 square foot living room that is the most common mini split job, and it is the size most DIY kits are built around. The Senville LETO 12,000 BTU, a popular DIY model, carries more than 2,200 Amazon ratings at 4.4 stars as of October 2026, with a 20.8 SEER rating and heat-pump operation down to 5 degrees Fahrenheit. If your result is 12,000 BTU, you are shopping in the deepest part of the market, with the most models and the most reviews to compare.
18,000 and 24,000 BTU cover open plans. The jump from 12,000 to 18,000 is the biggest single step in the range, a 50 percent increase, which is why borderline rooms land awkwardly: a computed load of 12,100 BTU rounds to an 18,000 BTU head. Before accepting that jump, check the inputs: a room that is really two rooms with a doorway between them should be sized as two heads, not one big one, and a load that only just crosses the line may be better served by the smaller head plus better shading or sealing.
30,000 BTU exists between 24,000 and 36,000. Some brands sell a 30,000 BTU head, and some sizing guides list it as a standard size. This sizer rounds to the five sizes in its list, 9,000, 12,000, 18,000, 24,000, and 36,000, so a load of 25,000 BTU recommends a 36,000 BTU head. If the brand you are shopping sells a 30,000 BTU model, it is a legitimate middle step for loads between 24,000 and 30,000 BTU, and your installer can confirm the fit.
Voltage follows size. Smaller 9,000 to 12,000 BTU models may run on a standard 115-volt circuit, while larger systems need a dedicated 208/230-volt circuit, so check the nameplate before you buy and check with an electrician that your panel has room. The voltage question matters most for DIY installs, where the electrical work is the part most often underestimated.
The chart and the rule: why two published answers differ
Two respected sources give different answers for the same room, and it is worth saying why, because the difference confuses shoppers. ENERGY STAR's chart is banded: every room in a band gets the same capacity, so a 151 square foot room and a 249 square foot room both get 6,000 BTU. The 20 BTU per square foot rule is continuous: the 151 square foot room gets 3,020 BTU and the 249 square foot room gets 4,980. On small rooms the chart runs much higher than the rule. A 150 square foot bedroom is 5,000 BTU on the chart, which is 33 BTU per square foot, against 3,000 BTU from the rule. On large rooms the two converge: a 2,000 square foot space is 30,000 BTU on the chart, which is 15 BTU per square foot, against 40,000 BTU from the rule, where the rule now runs higher.
The chart was written for window room air conditioners, not mini splits, and its bands reflect the sizes window units were sold in. The rule is the HVAC industry's shorthand for cooling load in a typical home. Neither is wrong; they answer slightly different questions. This sizer uses the rule as its base, because it scales smoothly with room size and because every mini split sizing guide uses it, and it shows the chart figure as a cross-check so you can see both. When the two disagree by a size, as they do on a 300 square foot room, where the chart says 8,000 and the rule says 6,000, the practical answer is the same either way: both round up to a 9,000 BTU head.
There is a second disagreement hidden inside the chart. ENERGY STAR's own example in its guidance is a 147.5 square foot room needing 5,000 BTU, which is 34 BTU per square foot, far above the 20 BTU rule. That is the chart's small-room band doing its work: the smallest window unit was 5,000 BTU, so the smallest band starts there. Mini splits have the same floor in a different place: the smallest common head is 9,000 BTU. The practical lesson is the same in both cases. Small rooms are oversized by the smallest available unit, and the right response is an inverter compressor that can run at part load, not a fruitless search for a smaller machine.
Heating in cold climates: size for winter too
A mini split is a heat pump, and a heat pump's heating output falls as the outdoor temperature falls. The nameplate heating capacity is measured at 47 degrees Fahrenheit, a mild autumn day, and it says nothing about what the unit delivers on a 5-degree night. That gap is the most common sizing mistake in cold climates: a unit picked for its cooling load, or for its nameplate heating number, comes up short in the coldest weeks.
The numbers make the point concretely. ENERGY STAR lists the MRCOOL DIY 5th Gen 12,000 BTU model at 8,400 BTU per hour of heating at 5 degrees Fahrenheit, about 70 percent of its 12,000 BTU rating. That is not a defect; it is how heat pumps work. The colder the outdoor air, the less heat there is in it to move indoors.
Two published standards draw the line for cold-climate equipment. To earn the ENERGY STAR cold climate designation, a heat pump must keep at least 70 percent of its 47-degree heating capacity at 5 degrees Fahrenheit, at a coefficient of performance of at least 1.75. The Northeast Energy Efficiency Partnerships, NEEP, maintains a cold-climate specification and product list, and its sizing guide recommends sizing a full-replacement system to meet 100 to 115 percent of the home's estimated heating load at the local design temperature, without auxiliary heat. The design temperature is the cold outdoor temperature your area plans heating around, typically the temperature exceeded by 99 percent of winter hours, and your installer can look it up for your location.
The practical steps for a cold climate are straightforward. First, size the cooling load with this sizer. Second, ask your installer for a Manual J heating load for the same room. Third, compare the heating load against the model's published heating capacity at your design temperature, from the manufacturer's extended performance table, not the nameplate. If the capacity at design temperature falls short, the answer is a larger unit, a cold-climate model with better low-temperature output, or a backup heat source for the coldest days. ENERGY STAR says cold-climate units keep working below 5 degrees, paired with backup heat for the coldest hours. This sizer's cooling recommendation is the starting point for that conversation, not the end of it.
Common mistakes to avoid
Rounding up two sizes "to be safe." The most common mistake in mini split sizing, and the most expensive. An oversized unit cools the room in minutes, shuts off before the coil has run long enough to pull moisture out of the air, and leaves the room cold and damp. The Department of Energy says oversized or poorly placed air handlers short-cycle, wasting energy and failing to provide proper temperature and humidity control. ENERGY STAR says the same: bigger is not always better. Round up one size, to the next standard head, and stop there.
Sizing one head for two rooms. Air from one head does not pass a closed door, and it moves poorly through an open doorway. Two rooms need two heads, on a multi-zone system or as separate single-zone units. The one exception is a genuinely open plan with no door between the spaces, which counts as one room and should be measured as one area.
Forgetting the ceiling. A 10-foot ceiling holds 25 percent more air than an 8-foot ceiling over the same floor, and a 12-foot ceiling holds 50 percent more. Every published rule assumes 8 feet. If your ceiling is taller and you skip the adjustment, you buy a unit that is a quarter to a half too small. Vaulted ceilings are worse: the volume above the 8-foot line is easy to forget and hard to cool.
Measuring half an open floor plan. Air does not stop at the edge of the rug. An open kitchen and living room is one air space, and the head has to cool all of it, plus the 4,000 BTU of cooking heat. Measure the whole connected area, or the unit will be sized for a room that does not exist.
Ignoring the kitchen allowance. Cooking heat is the largest single adjustment for most rooms: 4,000 BTU is more than the entire base load of a 200 square foot room. A kitchen-diner sized without it will run flat out every time the oven is on. If the head serves any space where cooking happens, pick the kitchen room type.
Sizing for cooling in a cold climate and forgetting heating. In a cold climate the heating load often exceeds the cooling load, and a unit picked on cooling alone comes up short in January. Check the heating capacity at your design temperature, and read the cold-climate section above before you buy.
Trusting the nameplate heating number. The heating capacity on the box is measured at 47 degrees Fahrenheit. At 5 degrees a cold-climate model delivers about 70 percent of that, and a standard model delivers less. The number that matters is the capacity at your winter design temperature, from the manufacturer's extended performance table.
Buying before checking the electrics. Larger mini splits need a dedicated 208/230-volt circuit, and a full panel can add cost and time to the install. Check the nameplate voltage and the breaker size, and check with an electrician that your panel has room, before you buy, not after the unit is on the wall.
Frequently asked questions
What size mini split do I need for a 500 sq ft room?
A 500 sq ft room needs about 10,000 BTU by the 20 BTU per square foot rule, which rounds up to a 12,000 BTU (1 ton) mini split under average conditions. ENERGY STAR's chart gives the same answer directly: 12,000 BTU for 450 to 550 sq ft. Add 10 percent for a very sunny room, 4,000 BTU if the room includes a kitchen, or 20 percent for poor insulation, and the load can climb past 12,000 BTU toward an 18,000 BTU head. A 500 sq ft room with 10-foot ceilings, strong sun, poor insulation, and a hot climate needs about 18,975 BTU, which rounds up to a 24,000 BTU head.
How many BTU per square foot does a mini split need?
About 20 BTU per square foot is the standard baseline for cooling in a typical room with 8-foot ceilings, average insulation, and average sun. That is the long-standing rule of thumb in HVAC sizing, used by the Department of Energy and ENERGY STAR guidance. Challenging conditions push it higher: 25 to 30 BTU per square foot for a hot climate, poor insulation, tall ceilings, or strong sun. ENERGY STAR's banded chart works out to 24 to 40 BTU per square foot on small rooms and 15 to 20 on large ones, because the chart steps in fixed bands rather than scaling smoothly. This sizer starts at 20 and adjusts for your room's actual conditions.
Is a 12,000 BTU mini split enough for a 600 sq ft room?
Yes, under average conditions. A 600 sq ft room at 20 BTU per square foot needs exactly 12,000 BTU, so a 12,000 BTU (1 ton) head is an exact fit with 8-foot ceilings, average sun, average insulation, and a moderate climate. It is not enough once the conditions stack up: a 10-foot ceiling alone pushes the load to 15,000 BTU, and a sunny room with poor insulation in a hot climate pushes it past 18,000 BTU. ENERGY STAR's chart gives 14,000 BTU for a 600 sq ft room before adjustments, which is a reminder that the chart runs higher than the rule. If your 600 sq ft room has any two of tall ceilings, strong sun, poor insulation, or a hot climate, size up to 18,000 BTU.
What happens if a mini split is too big?
An oversized mini split short-cycles: it cools the air fast, reaches the thermostat setting in minutes, and shuts off before the coil has run long enough to pull moisture out of the air. The room ends up cold and damp, the unit wastes energy on frequent starts, and the compressor wears faster. The Department of Energy says oversized or poorly placed air handlers waste energy and fail to provide proper temperature or humidity control, and ENERGY STAR says bigger is not always better for the same reason. Inverter compressors soften the problem, because they ramp down to part load instead of switching off, but they do not erase it: a head far above the load still short-cycles on mild days. Round up one size, never two.
Does ceiling height change the mini split size I need?
Yes. Every published sizing rule assumes an 8-foot ceiling, because the rule is really about air volume, not floor area. A 10-foot ceiling holds 25 percent more air than an 8-foot ceiling over the same floor, so multiply the base load by 10 divided by 8, which is 1.25. A 500 sq ft room that needs 10,000 BTU with an 8-foot ceiling needs 12,500 BTU with a 10-foot ceiling, which rounds up from a 12,000 BTU head to an 18,000 BTU head. A 12-foot ceiling gives a factor of 1.5. ENERGY STAR says higher ceilings call for higher capacity without giving a number; this sizer uses the volume ratio, ceiling height divided by 8, and states that openly as its own adjustment.
What size mini split do I need for heating in a cold climate?
In a cold climate, size for the heating load, not just the cooling load, because the heating load is often larger. This sizer sizes for cooling, so treat its result as the starting point. Then ask your installer for a Manual J heating load and compare it against the model's published heating capacity at your winter design temperature, from the manufacturer's extended performance table, not the nameplate, which is measured at 47 degrees Fahrenheit. A heat pump's output falls as it gets colder: ENERGY STAR lists a 12,000 BTU model at 8,400 BTU of heating at 5 degrees Fahrenheit, about 70 percent of its rating. To earn the ENERGY STAR cold climate designation, a model must keep at least 70 percent of its 47-degree heating capacity at 5 degrees. NEEP recommends sizing to 100 to 115 percent of the heating load at the design temperature.
Can one mini split cool two rooms?
No, not with one indoor head. One head conditions one continuous space: air moves poorly through an open doorway and not at all through a closed door. Two rooms need two heads, either on a multi-zone system with one outdoor unit feeding both, or as two separate single-zone units. The Department of Energy notes that many models support up to four indoor units on one outdoor unit. Size each head to its own room with this sizer, room by room, and have the installer confirm the outdoor unit can carry them all. An open floor plan with no door between the spaces counts as one room and takes one head, sized for the whole open area.
Sources
- U.S. Department of Energy, Ductless Mini-Split Air Conditioners (mini splits suit homes without ducts and room additions; many models support up to four indoor units on one outdoor unit; the outdoor unit can sit up to 50 feet from the indoor unit; duct losses can exceed 30 percent of space-conditioning energy; oversized or poorly placed air handlers short-cycle, wasting energy and failing to control temperature and humidity; mini splits cost about 30 percent more than central systems excluding ductwork and up to twice as much as window units; mini splits have lower-rated filters and a separate air cleaner may be necessary): energy.gov/energysaver/ductless-mini-split-air-conditioners (accessed 19 November 2026).
- U.S. Environmental Protection Agency and U.S. Department of Energy, ENERGY STAR Room Air Conditioners buying guidance (the cooling capacity chart: 5,000 BTU for 100 up to 150 sq ft through 34,000 BTU for 2,000 up to 2,500 sq ft, calculated for an 8-foot ceiling; reduce capacity by 10 percent for a heavily shaded room; increase by 10 percent for a very sunny room; add 600 BTU for each person beyond two who regularly occupies the room; add 4,000 BTU for a kitchen; an oversized unit cools the room before removing humidity): images.homedepot.ca (EPA buying guidance, mirrored as a Home Depot PDF) (accessed 19 November 2026).
- DuctlessWise, What Size Mini Split Do I Need? BTU Sizing Guide (about 20 BTU per square foot; one ton equals 12,000 BTU; the ENERGY STAR chart adapted to mini split head sizes; the smallest mini splits start at 6,000 BTU for rooms under 250 sq ft; sun, shade, occupancy, and kitchen adjustments; oversizing and short-cycling; MRCOOL DIY 5th Gen 12k heating of 8,400 BTU per hour at 5 degrees Fahrenheit, about 70 percent of its rating): ductlesswise.com/articles/mini-split-sizing-guide/ (accessed 19 November 2026).
- EcoFlow, How Big of a Mini Split Do I Need? BTU Sizing Guide (the ENERGY STAR chart reproduced in full; mini splits come in set sizes, often 9,000, 12,000, 18,000, and 24,000 BTU per hour; round to the nearest size and do not jump two sizes; one ton equals 12,000 BTU per hour per an Oklahoma State University fact sheet; Manual J decides the final size; smaller 9,000 to 12,000 BTU models may run on 115V while larger systems need a dedicated 208/230V circuit; cold-climate heating capacity at the winter design temperature): ecoflow.com/us/blog/how-big-of-a-mini-split-do-i-need (accessed 19 November 2026).
- NumbrWiz, Mini Split Calculator (base BTU equals room square footage times 20 BTU per sq ft; ceiling factors 1.0 at 8 ft, 1.10 at 9 ft, 1.20 at 10 ft, 1.35 vaulted; insulation factors excellent 0.85, good 1.0, average 1.15, poor 1.30; sun factors shaded 0.90, moderate 1.0, sunny 1.15, extreme 1.25; climate factors mild 0.90, moderate 1.0, hot 1.15, very hot 1.30; common sizes 9,000, 12,000, 18,000, 24,000, 30,000, and 36,000 BTU; 20 to 30 BTU per sq ft for challenging conditions): numbrwiz.com/construction-calculators/hvac/mini-split-calculator.html (accessed 19 November 2026).
- AC Tune-Up Company, How Do I Calculate Mini-Split Size From Room Dimensions? (20 to 25 BTU per square foot, 20 for mild and well-insulated rooms, 25 for hot and humid or sun-exposed rooms; add 10 to 20 percent for ceilings above 8 feet, 10 percent for unshaded west or south glass, 20 percent for thin insulation, 4,000 BTU for kitchen heat, 600 BTU per person past two; size up in humid climates and down in mild ones; oversizing causes short-cycling and damp rooms): ac-tune-up-company-near-me.com/how-do-i-calculate-mini-split-size-from-room-dimensions (accessed 19 November 2026).
- Mitsubishi Electric, MSZ-GL06NA Submittal Data (6,000 BTU per hour wall-mounted indoor unit; cooling capacity 6,000 BTU per hour; heating capacity 7,200 BTU per hour): sidharvey.com/documents/MSZ-GL06NA-U1.PDF (accessed 19 November 2026).
- HVACBase, Do Heat Pumps Work in Cold Weather? (an ENERGY STAR cold-climate heat pump must deliver at least 70 percent of its 47-degree capacity at 5 degrees Fahrenheit at a COP of at least 1.75; NEEP reports each model's heating capacity at 47, 17, and 5 degrees Fahrenheit; heat pumps are sized to a design temperature, not the record low): hvacbase.org/heat-pump-in-cold-weather (accessed 19 November 2026).
- EcoFlow, Cold Climate Heat Pump Buyer's Guide (ENERGY STAR cold climate certification requires third-party testing down to 5 degrees Fahrenheit and at least 70 percent of rated heating capacity at 47 degrees when operating at 5 degrees; NEEP recommends sizing a full replacement system to meet 100 to 115 percent of the home's estimated heating load at the design temperature; operating at a temperature does not mean delivering full heating capacity at that temperature): ecoflow.com/us/blog/cold-climate-heat-pump (accessed 19 November 2026).
- Portable AC Lab, Portable AC BTU Guide 2026 (ENERGY STAR's room-sizing guidance built around the 20 BTU per square foot rule; a 147.5 sq ft room, in ENERGY STAR's own example, needs 5,000 BTU; the four adjustments for shade, sun, kitchens, and occupants; the EPA recommends keeping indoor relative humidity between 30 and 50 percent): portableaclab.com/guides/portable-ac-btu-guide/ (accessed 19 November 2026).
- Indoor Breathing, Best Mini-Split Air Conditioners (Senville LETO 12,000 BTU mini split, 4.4 stars from 2,203 ratings, checked on Amazon on 22 October 2026; Senville LETO 24,000 BTU, 4.5 stars from 2,007 ratings): indoorbreathing.com/ductless-mini-split-air-conditioners/ (accessed 19 November 2026).
- Of Zen and Computing, 12 Best Ductless Heat Pumps for Cold Climates (Senville LETO 12,000 BTU, 20.8 SEER, heat-pump operation down to 5 degrees Fahrenheit, more than 2,100 reviews): ofzenandcomputing.com/best-ductless-heat-pumps-for-cold-climates/ (accessed 19 November 2026).