Rain Garden Size Calculator
Verified Last reviewed: 21 November 2026. Page history
Your rain garden
How the numbers were worked out
Plan the rest of the project: our Soil Test Interpreter reads your soil test results, our Native Plant Finder picks plants suited to your site, our Pollinator Garden Planner plans a pollinator planting for the same bed, our Compost Bin Size Calculator sizes a bin for the garden waste, and our Garden Watering Calculator works out watering for new plants.
Free to use — no sign-up, no paywall. Spotted a mistake? Tell us — we fix reported errors within 24 hours.
Your inputs stay in your browser: every calculation runs on your device, and nothing you type is sent to our servers.
Last reviewed: 21 November 2026. Reviewed every 180 days; next review due 19 May 2027.
How to use the Rain Garden Size Calculator
A rain garden is a shallow planted basin that catches runoff from a roof, driveway, or patio and lets it soak into the ground instead of running into the street. Sizing is the step most homeowners get wrong: too small and the garden overflows in every storm, too large and the digging bill doubles for no benefit. This calculator sizes the garden the way the extension guides do, from the area draining into it, the soil under it, and the slope of the ground. It gives you the garden area, the ponding depth, a 2 to 1 shape you can stake out with a hose, the number of plants to buy, how much water the garden holds at full ponding, and how much mulch to order.
The sizing follows the University of Wisconsin-Extension table published in Nebraska Extension NebGuide G1758. The table gives a size factor for each combination of soil type and depth: multiply your drainage area by the factor and you have the garden area. The factors are designed to control 100 percent of runoff in an average rainfall year. Clay drains slowly, so clay gardens are the largest at every depth; sandy soil drains fast, so sandy gardens are the smallest. A garden far from the downspout uses a much smaller factor, because some runoff soaks into the lawn on the way.
To get your result, follow these steps:
- Enter the drainage area. This is the roof, driveway, and patio area that sheds water toward the garden, in square feet. For a garden fed by one downspout, enter only the roof area that downspout serves, not the whole roof. A house with four downspouts that each drain a quarter of the roof sends 25 percent of the footprint to each one, so a 2,400 square foot footprint means 600 square feet per downspout. Add any driveway or patio section that slopes toward the garden. If you need the footprint first, measure the length and width of the house and multiply, or use our Area Calculator for an odd shape.
- Choose the soil type. Sandy soil drains fast, silty soil drains at a middle pace, and clayey soil drains slowly. Soil type changes the answer more than any other input: on a shallow garden, the same 1,000 square feet of roof needs 190 square feet of garden on sand, 340 on silt, and 430 on clay. If you do not know your soil, run the ribbon test described in the soil section below, or send a sample to your county extension office. Our Soil Test Interpreter reads the results when they come back.
- Enter the ground slope. Slope sets the depth, because the bottom of the garden must be level. Measure it with two stakes 100 inches apart and a level string, as the extension guides describe: the drop in inches over 100 inches is the slope in percent. Under 5 percent calls for a 3 to 5 inch deep garden, 5 percent to under 8 percent calls for 6 to 7 inches, and 8 percent to 12 percent calls for 8 inches. A slope over 12 percent is too steep for a rain garden at that spot, and the calculator will tell you to pick a flatter location.
- Choose the distance from the downspout. Less than 30 feet is the usual case, a garden beside the house fed by a short pipe or swale. Thirty feet or more means the garden sits out in the yard, catching runoff that has already crossed lawn, and the size factor drops sharply: sandy soil goes from 0.19 to 0.03, silty from 0.34 to 0.06, and clayey from 0.43 to 0.10 at the shallow depth.
- Choose the plant spacing. Native perennials are usually planted 12 inches apart, one plant per square foot, so the canopy closes in one season and weeds have nowhere to start. Wider spacing suits large grasses and shrubs: 18 inches gives one plant per 2.25 square feet, and 24 inches gives one plant per 4 square feet. The calculator counts plants from the garden area and the spacing you choose, rounding up so you never come up one plant short.
The tool updates as you type, so you can try different numbers quickly. Try the example buttons under the form: the first is a 600 square foot roof section on silty soil at a 4 percent slope, which gives a 204 square foot garden; the second is a 1,500 square foot roof on clay at a 6 percent slope, which splits into two gardens; and the third is an 800 square foot roof on sand at a 10 percent slope, far from the downspout, which gives a small 24 square foot garden. The three examples show the three shapes the answer takes: one garden, a split pair, and a small far garden.
Read the full result, not just the headline. The headline leads with the garden area, the depth, and the plant count. The cards show the shape, the storage at full ponding, the runoff from 1 inch of rain, the mulch needed, and the size factor used. The factor table shows all three depth bands for your soil, with your band highlighted, so you can see what a deeper garden would save. The guidance explains the result in plain language, the warnings flag clay soil, steep slopes, and overflow risk, the steps print the full working so you can check every figure, and the notes carry the siting rules that keep the garden safe.
How it works
The calculator runs six calculations in order: the depth band from the slope, the size factor from the soil and the depth, the garden area, the split into gardens, the shape, and the planting and materials. Each one uses the result of the one before it, and the steps section on the page prints all six so you can check them against your own arithmetic.
Step 1: depth from slope
The bottom of a rain garden must be level, so the water spreads out instead of pooling in one corner. On flat ground that is easy, and a shallow garden is enough. On a slope, the uphill side must be dug deeper to reach a level bottom, so the garden ends up deeper. The extension guides tie the depth to the slope in three bands:
| Ground slope | Ponding depth | Midpoint used for storage |
|---|---|---|
| Under 5% | 3 to 5 inches | 4 inches |
| 5% to under 8% | 6 to 7 inches | 6.5 inches |
| 8% to 12% | 8 inches | 8 inches |
| Over 12% | Too steep: pick a different site | No garden |
The calculator uses the midpoint of each band for the storage calculation: 4 inches for the shallow band, 6.5 inches for the middle band, and 8 inches for the deep band. A garden deeper than 8 inches takes too long to drain, and the guides cap the depth there. A garden shallower than 3 inches would need to be very large to hold the same water, so the shallow band starts at 3 inches.
Step 2: the size factor
The size factor is the heart of the method. It comes from the University of Wisconsin-Extension table in the Wisconsin rain garden manual, as published in Nebraska Extension NebGuide G1758. The factor depends on the soil type, the depth band, and the distance from the downspout. Deeper gardens get smaller factors, because each square foot of a deep garden holds more water. Sandy soil gets the smallest factors, because it drains fast and the garden empties between storms. Clay gets the largest, because it drains slowly and the garden must hold more water at once.
| Soil type | 3 to 5 inches deep | 6 to 7 inches deep | 8 inches deep | 30 feet or more away |
|---|---|---|---|---|
| Sandy soil | 0.19 | 0.15 | 0.08 | 0.03 |
| Silty soil | 0.34 | 0.25 | 0.16 | 0.06 |
| Clayey soil | 0.43 | 0.32 | 0.20 | 0.10 |
You will often hear a simpler rule: make the rain garden 20 to 30 percent of the drainage area. That rule is a rough summary of this table, and it is right in the middle of the range. Silty soil at the middle depth gives 25 percent, which sits inside the rule. But the table shows how far the real answer can move: a sandy garden at 8 inches deep is only 8 percent of the drainage area, and a clay garden at 3 to 5 inches deep is 43 percent. Using the flat 20 to 30 percent rule on clay would undersize the garden by nearly half, and using it on deep sand would oversize it by three times. The table is the better tool, and it is the one this calculator uses. Some county guides go further still: Gwinnett County in Georgia sizes clay gardens at 60 percent of the drainage area. The UW table used here tops out at 43 percent, and the calculator follows the UW table, because it is the published extension standard with a depth adjustment built in.
Step 3: garden area and the split
Garden area is drainage area times the size factor. A 600 square foot roof section on silty soil at the shallow depth gives 600 times 0.34, which is 204 square feet. A typical home rain garden runs 100 to 300 square feet. If the calculated area is more than 300 square feet, the guides say to divide it into smaller gardens, because a single garden over 300 square feet is hard to dig and plant by hand. The calculator splits the area into the smallest number of gardens that keeps each one at or under 300 square feet: 480 square feet becomes two gardens of 240 square feet each, and 860 square feet becomes three gardens of about 286.7 square feet each. If the full size does not fit your yard, you can shrink it: reducing the size by up to 30 percent still controls about 90 percent of average runoff, according to the same guide.
Step 4: shape
The guides recommend a length to width ratio of at least 2 to 1, with the long side running across the slope, perpendicular to the water entering the garden. That orientation spreads the incoming water across the widest face and maximizes the amount the garden can hold. The calculator works out the shape from the area: the width is the square root of half the area, and the length is twice the width. A 204 square foot garden comes out about 10.1 feet wide by 20.2 feet long. The shape is a starting point, not a rule: crescent, oval, teardrop, and kidney shapes all work, and curves fit a landscape better than a rectangle. On slopes of 8 percent or more, the guides cap the width at 15 feet, because a wide garden on a steep slope needs very deep digging on the uphill side. With the 300 square foot split, a 2 to 1 garden never gets wider than about 12.2 feet, so the cap never binds on a home garden built this way.
Step 5: storage and runoff
Storage is the volume the garden holds when it is full to the top of its ponding depth: garden area times depth, converted to gallons at 7.48052 gallons per cubic foot. A 204 square foot garden at 4 inches deep holds 204 times one third of a cubic foot per square foot, which is 68 cubic feet, or 509 gallons. Runoff is the volume 1 inch of rain drops on the drainage area: 1 inch of rain on 1,000 square feet is 623 gallons, so 1 inch on 600 square feet is 374 gallons. The calculator compares the two. If storage is less than the runoff from 1 inch of rain, the garden will overflow in a 1 inch storm, and it needs an overflow outlet to a safe spot. That is common on sandy soil at the deep band, where the factor is small: the garden still works, because sandy soil drains during the storm, but the overflow must go somewhere safe.
Step 6: plants and mulch
Plant count comes from the garden area and the spacing. At 12 inch spacing, each plant gets 1 square foot, so a 204 square foot garden needs 204 plants. At 18 inch spacing, each plant gets 2.25 square feet, so the same garden needs 91 plants. At 24 inch spacing, each plant gets 4 square feet, so it needs 51 plants. The count always rounds up, and for split gardens it is worked out per garden and then added up. Mulch is 2 inches deep over the whole garden, which Penn State Extension recommends as a top dressing to keep weeds out and moisture in. Two inches over 204 square feet is 34 cubic feet, or 1.3 cubic yards. For clay soil, the calculator also works out the soil replacement volume: replacing the top 2 feet with rain garden mix over 480 square feet is 960 cubic feet, or 35.6 cubic yards.
| Plant spacing | Area per plant | Plants for a 204 sq ft garden |
|---|---|---|
| 12 inches | 1 square foot | 204 |
| 18 inches | 2.25 square feet | 91 |
| 24 inches | 4 square feet | 51 |
Worked example 1: one downspout on silty soil
A 600 square foot roof section, silty soil, 4 percent slope, garden beside the house, 12 inch spacing.
- Depth band: a 4% slope calls for a 3 to 5 inches deep garden.
- Size factor: silty soil at 3 to 5 inches deep gives 0.34.
- Garden area: 600 sq ft x 0.34 = 204 sq ft (34% of the drainage area).
- Shape: a 2 to 1 shape gives about 10.1 ft wide by 20.2 ft long.
- Storage: 204 sq ft x 4 in deep holds about 509 gallons at full ponding.
- Runoff: 1 inch of rain on 600 sq ft is about 374 gallons.
- Plants: 204 sq ft at 12 inch spacing needs 204 plants.
- Mulch: 2 inches of mulch over 204 sq ft is about 1.3 cubic yards.
Worked example 2: a big roof on clay
A 1,500 square foot roof section, clayey soil, 6 percent slope, garden beside the house, 18 inch spacing.
- Depth band: a 6% slope calls for a 6 to 7 inches deep garden.
- Size factor: clayey soil at 6 to 7 inches deep gives 0.32.
- Garden area: 1,500 sq ft x 0.32 = 480 sq ft (32% of the drainage area).
- Split: the full size is more than 300 sq ft, so 2 gardens of about 240 sq ft each.
- Shape: a 2 to 1 shape gives about 11 ft wide by 21.9 ft long for each garden.
- Storage: 480 sq ft x 6.5 in deep holds about 1,945 gallons at full ponding.
- Runoff: 1 inch of rain on 1,500 sq ft is about 935 gallons.
- Plants: 240 sq ft per garden at 18 inch spacing needs 107 plants per garden, 214 plants in total.
- Mulch: 2 inches of mulch over 480 sq ft is about 3 cubic yards.
- Clay soil: replacing the top 2 feet with rain garden mix takes about 35.6 cubic yards.
Worked example 3: sandy soil far from the house
An 800 square foot roof section, sandy soil, 10 percent slope, garden 30 feet or more from the downspout, 24 inch spacing.
- Depth band: a 10% slope calls for an 8 inches deep garden.
- Size factor: sandy soil 30 feet or more from the downspout gives a factor of 0.03 for all depths.
- Garden area: 800 sq ft x 0.03 = 24 sq ft (3% of the drainage area).
- Shape: a 2 to 1 shape gives about 3.5 ft wide by 6.9 ft long.
- Storage: 24 sq ft x 8 in deep holds about 120 gallons at full ponding.
- Runoff: 1 inch of rain on 800 sq ft is about 499 gallons.
- Plants: 24 sq ft at 24 inch spacing needs 6 plants.
- Mulch: 2 inches of mulch over 24 sq ft is about 0.1 cubic yards.
This garden holds less than the runoff from 1 inch of rain, so it will overflow in a 1 inch storm, and the calculator warns you to build an overflow outlet. It is also a small garden, below the usual 100 to 300 square feet, but any size helps: it still catches runoff that would otherwise reach the street.
Rain garden sizing by soil type
Soil type is the key to an effective rain garden, because the soil must let water soak in fast enough that the garden drains in 24 to 48 hours when it is full. The extension guides set a minimum infiltration rate of 0.25 inches per hour: slower than that, and the garden stays wet too long, stresses the plants, and can breed mosquitoes. Soils high in sand and silt usually drain well enough. Soils high in clay often do not, which is why clay gardens are sized larger and why clay is the one soil type that regularly needs amendment before planting.
Before you trust the soil type you entered, test it at the exact spot where the garden will go. Soils vary dramatically from place to place, and they can vary within the same yard. Topsoil is often removed from home sites before construction, which exposes subsoil with a higher clay content and a slower infiltration rate. Two simple tests come from Nebraska Extension NebGuide G1758. The first is the hole test: dig a hole 6 inches deep, fill it with water, and check whether the water drains away in less than 24 hours. If it takes more than 24 hours to soak in, the site is not suitable as it stands. Run the test in spring or in the typical rainy season, not in the middle of summer or fall when dry, cracked soil can give a misleading result. The second is the ribbon test: take about half a cup of soil, add a few drops of water, and knead it into a ball. If the soil crumbles apart and will not stay together, it is suitable. If it forms a ball, squeeze a ribbon of soil between your thumb and index finger and let it grow until it breaks. If the ribbon is longer than an inch before it breaks and the soil feels more smooth than gritty, the soil is clayey and may not be suitable without amendment.
For clay soil, the standard fix is to replace the top 2 feet with rain garden mix. Rain Gardens of West Michigan recommends a mix of 50 to 60 percent sand, 20 to 30 percent topsoil, and 20 to 30 percent compost. The calculator works out the volume for you: a 480 square foot clay garden needs about 35.6 cubic yards of mix. One cubic yard is 27 cubic feet, so the arithmetic is garden area times 2 feet deep, divided by 27. If you are not replacing the soil, the West Michigan guide recommends double digging to a depth of 2 feet to loosen heavy clay, and mixing 2 to 4 inches of compost into the existing soil. Gwinnett County in Georgia gives a similar compost recommendation and notes that for high clay soils it may help to remove 1 to 2 feet of soil and replace it with a more porous mix. Whichever route you take, run the hole test again after amending, and do not plant until the soil passes.
Sandy soil has the opposite problem: it drains so fast that the garden can be small, but the plants may dry out between storms. The UW table gives sandy soil the smallest factors, down to 0.08 at the deep band beside the house and 0.03 far from the downspout. A sandy garden still needs the same 2 inches of mulch, and the plants still need watering in their first season while their roots establish. Silty soil sits in the middle at every depth, which is why the calculator defaults to silty when you do not choose a soil type.
Where to put a rain garden
Siting rules matter as much as sizing, because a well sized garden in the wrong place can damage a foundation or a septic system. The rules below come from Penn State Extension and Nebraska Extension, and the calculator carries the strictest version of each one in its notes.
- At least 10 feet from the house. Every guide agrees on this one. Infiltrating water near a foundation can seep into a basement or crawl space. Ten feet is the minimum; further is better, and the garden should sit downslope from the building so water flows away from the house.
- At least 50 feet from a septic system and 100 feet from a well. These are the Penn State Extension figures, and they are the ones the calculator uses. Nebraska Extension lists 25 feet for both septic systems and wellheads. The tool follows the stricter Penn State distances, because the cost of getting this wrong is a contaminated well or a failed septic field, and the stricter number costs nothing but a longer pipe.
- On ground sloping 12 percent or less. A steeper slope needs too much digging to make a level bottom, and the downhill berm gets too tall to hold safely. If the only available spot is steeper than 12 percent, pick a different location or terrace the slope first.
- Call 811 before you dig. Underground utility lines run through most yards, and a shovel can cut a gas line or a fiber cable. Penn State Extension advises calling PA One Call at 811 before digging; 811 is the national call-before-you-dig number in the United States.
- Not under a tree canopy, not over a septic field, and not where water already pools. Tree roots compete with the garden plants and make digging hard. A spot where water already pools may have a high water table, and the guides want the water table at least 2 feet below the soil surface. A rain garden is not a pond: it is dry most of the time and holds water only after a rain.
- Where the water already goes. Watch the yard during a heavy rain before you stake anything. The best spot is the low area where runoff already collects, or the line downslope from the downspout that drains the most roof. Penn State Extension calls observing the property during a significant rain event the most useful site assessment step, because you see exactly where water collects, where it flows, and where it exits the property.
Shape the garden with a hose or string before you dig, and dig the bottom level. Use the soil from the uphill side to build a low berm on the downhill side, which holds the ponded water in the garden. The top of the berm should not be higher than the uphill edge of the garden. Leave an overflow notch in the berm at its lowest point, lined with rock, so big storms spill out safely instead of cutting a channel through the berm. A buried 4 inch corrugated pipe from the downspout to the garden, pitched 1 to 2 percent, carries roof water by gravity without holding standing water.
What to plant in a rain garden
A rain garden has three moisture zones, and the plants must match the zone they sit in. The center and lowest point is the pond zone, which may sit in standing water for 12 to 48 hours after a major storm. Only plants that tolerate intermittent flooding survive there: swamp milkweed, blue flag iris, cardinal flower, and sedges are standard choices. The middle slopes stay wet after rain but dry out between storms, which suits most native rain garden plants: black-eyed susan, switchgrass, joe-pye weed, and coneflower. The top rim and the berm behave like normal garden soil and take drought-tolerant plants: little bluestem, asters, and prairie grasses. Penn State Extension advises planting close together, choosing plants with a variety of shapes, colors, and bloom times for pollinator habitat, and watching the new garden after a storm to mark which areas stay wet longest before finalizing the planting.
Native plants are preferred, because their deep roots open channels in the soil that speed infiltration over time, and because they are adapted to the local wet and dry cycle. The University of Wisconsin rain garden manual lists most perennials at 1 foot spacing, with larger plants such as white false indigo at 2 feet. The Dane County guide puts it simply: plan on one plant per square foot of garden. That is the 12 inch spacing this calculator defaults to. At that spacing a 204 square foot garden needs 204 plants, which sounds like a lot until you price native plugs at 2 to 5 dollars each: the planting for that garden runs roughly 400 to 1,000 dollars, and the canopy closes in one season. Our Native Plant Finder picks species suited to your site, our Pollinator Garden Planner plans a pollinator planting for the same bed, and our Wildflower Seeding Calculator works out seed rates if you would rather sow than plant plugs. For the shrubs and grasses around the garden, our Bird-Friendly Garden Planner and Butterfly Garden Planner extend the habitat beyond the basin.
Water new plants in their first season, and top dress with 2 inches of mulch to keep weeds out and moisture in. In the first year, weed regularly: bare soil between young plants invites weeds, and the mulch only slows them. After the first season the plants mostly take care of themselves. Cut back dead growth in late winter or early spring, replace any plants that did not survive, and check the inlet and overflow after big storms for sediment buildup. A rain garden that drains within 48 hours does not breed mosquitoes, because mosquito larvae need standing water for longer than that to develop.
Features
- Soil-aware sizing. The UW-Extension factor table adjusts the garden for sandy, silty, and clayey soil at three depth bands, plus a far-from-downspout column. Clay gardens come out larger, sandy gardens smaller, and the result table shows every band for your soil so you can see the trade-off.
- Depth from slope. Enter the slope and the calculator picks the depth band the guides recommend, from 3 to 5 inches on flat ground to 8 inches on a 12 percent slope, and refuses slopes over 12 percent with a clear message.
- Automatic splitting. Gardens over 300 square feet are split into the smallest number of gardens that keeps each one at or under 300 square feet, with the size of each garden, its shape, and its plant count.
- Storage against runoff. Every result compares the gallons the garden holds at full ponding with the gallons 1 inch of rain drops on the drainage area, and warns you when the garden will overflow in a 1 inch storm.
- Plant counts at three spacings. Twelve, 18, or 24 inch spacing, with the count rounded up per garden so you never come up short at the nursery.
- Materials in cubic yards. Mulch at 2 inches deep, and soil replacement mix at 2 feet deep for clay soil, both in the cubic yards a supplier quotes.
- Full working shown. Every result prints its steps, so you can check the factor, the multiplication, the split, the shape, the storage, and the plant count against your own arithmetic.
Use cases
A single downspout. The most common rain garden catches one downspout. Measure the roof area that downspout serves, enter it, and the calculator gives a garden you can dig in a weekend. A 600 square foot roof section on silty soil gives a 204 square foot garden, about 10 feet by 20 feet, with 204 plants at 12 inch spacing.
A whole roof on clay. Clay soil and a large roof is the combination that produces the biggest gardens. A 1,500 square foot roof on clay at a 6 percent slope needs 480 square feet of garden, which the calculator splits into two gardens of 240 square feet each. If two gardens do not fit, shrink the total by up to 30 percent and still control about 90 percent of average runoff.
A wet low spot far from the house. A garden 30 feet or more from the downspout uses the far factors, which run from about a sixth to about half of the near factors depending on the depth band. An 800 square foot roof on sand gives a 24 square foot garden out in the yard. Small gardens like this are easy to dig, but check the overflow: this one holds 120 gallons against 499 gallons of runoff from 1 inch of rain.
A driveway or patio. Driveways and patios shed as much water per square foot as a roof. Add the paved area that slopes toward the garden to the roof area before you enter it. A 400 square foot driveway section plus a 600 square foot roof section is a 1,000 square foot drainage area, which on silty soil at the shallow depth needs a 340 square foot garden, split into two gardens of 170 square feet each.
Replacing a lawn that floods. A lawn that ponds after every storm is often a sign of compacted soil or a low spot with nowhere for the water to go. A rain garden in the low spot gives the water a place to soak in. Rain gardens soak up 30 percent more water than an equivalent patch of lawn, according to Penn State Extension, and the deep-rooted native plants keep improving the soil year after year. If the flooding is severe, our Pond Build Cost Calculator prices a larger water feature, and our Garden Watering Calculator helps with the plants while they establish.
Sources
Every figure in this tool comes from a published extension or government source, re-verified on 21 November 2026. The sizing factors and depth bands come from the University of Wisconsin-Extension table in Rain Gardens: A How-to Manual for Homeowners, as published in Nebraska Extension NebGuide G1758, Stormwater Management: Rain Garden Design for Homeowners (Franti and Rodie), which also supplies the 0.25 inches per hour minimum infiltration rate, the 24 to 48 hour drainage rule, the hole and ribbon tests, the 100 to 300 square foot typical size, the 300 square foot split rule, the 2 to 1 shape ratio, the 15 foot width cap on steep slopes, and the 30 percent reduction rule. The same table is reproduced in the Washington State University guide Rain Gardens: Reusing Rain in the Pacific Northwest, which confirms the slope bands and the factor values.
The siting distances, the 2 inch mulch recommendation, the plant-close-together advice, and the 30 percent more water than lawn figure come from Penn State Extension, An Introduction to Rain Gardens and Rain Garden Resources from Penn State Extension. The definition of a rain garden and its role in reducing runoff and filtering pollutants come from the US Environmental Protection Agency, Soak Up the Rain: Rain Gardens. The soil replacement mix of 50 to 60 percent sand, 20 to 30 percent topsoil, and 20 to 30 percent compost, the 2 foot double-digging recommendation for clay, and the standard 6 inch ponding depth come from Rain Gardens of West Michigan, Create a Rain Garden. The slope-to-depth bands are confirmed in the Missouri Botanical Garden fact sheet Rain Gardens. The one plant per square foot rule comes from the Dane County, Wisconsin guide How to Build a Rain Garden, and the 1 foot plant spacing in the Wisconsin manual's planting plans. Where sources disagreed, the stricter or primary source governs: the UW table governs sizing over county rules of thumb, and the Penn State siting distances govern over the shorter Nebraska distances. The gallon conversion uses 7.48052 gallons per cubic foot, and one cubic yard is 27 cubic feet.
Frequently asked questions
How big should a rain garden be?
Multiply the drainage area by the size factor for your soil and depth. The University of Wisconsin-Extension table gives factors from 0.08 for sandy soil at 8 inches deep to 0.43 for clayey soil at 3 to 5 inches deep, so a 1,000 square foot roof needs 80 to 430 square feet of garden depending on soil and depth. The common 20 to 30 percent rule is a rough summary of this table: silty soil at the middle depth gives 25 percent, which sits inside the rule, but clay at the shallow depth needs 43 percent and deep sand needs only 8 percent. A typical home rain garden runs 100 to 300 square feet, and anything over 300 square feet should be split into smaller gardens.
How deep should a rain garden be?
The depth follows the slope of the ground, because the bottom must be level. Under 5 percent slope calls for 3 to 5 inches deep, 5 percent to under 8 percent calls for 6 to 7 inches, and 8 percent to 12 percent calls for 8 inches. A garden deeper than 8 inches takes too long to drain, and the guides cap the depth there. A slope over 12 percent is too steep for a rain garden at that spot, and you should pick a flatter location. Rain Gardens of West Michigan gives 6 inches as the standard ponding depth, which sits in the middle band.
Does soil type really change the size?
Yes, more than any other input. Clay drains slowly, so a clay garden must hold more water at once and needs a larger area: at the shallow depth, the same 1,000 square feet of roof needs 430 square feet of garden on clay, 340 on silt, and 190 on sand. Sandy soil drains fast, so the garden empties between storms and can be smaller. The calculator uses a separate factor for each soil type at each depth, and it warns you to run the infiltration test on clay before you dig: the soil must take in at least 0.25 inches of water an hour.
How many plants do I need for a rain garden?
At the standard 12 inch spacing, one plant per square foot: a 204 square foot garden needs 204 plants. At 18 inch spacing, each plant gets 2.25 square feet, so the same garden needs 91 plants. At 24 inch spacing, each plant gets 4 square feet, so it needs 51 plants. Native perennials are usually planted 12 inches apart so the canopy closes in one season and weeds have nowhere to start. Wider spacing suits large grasses and shrubs. The calculator counts plants from your garden area and spacing, rounding up so you never come up short.
How far from the house should a rain garden be?
At least 10 feet from the foundation, so infiltrating water cannot seep into a basement or crawl space. Penn State Extension also recommends at least 50 feet from a septic system and 100 feet from a well. Nebraska Extension lists 25 feet for both septic systems and wellheads, and this tool follows the stricter Penn State distances. Call 811 before you dig to mark underground utilities, and do not site the garden under a tree canopy, over a septic field, or where water already pools.
What if my soil is clay?
Clay drains slowly, so test it before you dig: dig a 6 inch hole, fill it with water, and check that it drains within 24 hours. If it does not, amend the soil or pick a different spot. The standard fix is to replace the top 2 feet with rain garden mix: 50 to 60 percent sand, 20 to 30 percent topsoil, and 20 to 30 percent compost, as recommended by Rain Gardens of West Michigan. A 480 square foot clay garden needs about 35.6 cubic yards of mix. If you are not replacing the soil, double dig to a depth of 2 feet and mix in 2 to 4 inches of compost, then run the hole test again before planting.
Will a rain garden breed mosquitoes?
No, if it drains properly. A rain garden is dry most of the time and holds water only after a rain. The guides require standing water to disappear within 48 hours, and mosquito larvae need standing water for longer than that to develop. The soil must take in at least 0.25 inches of water an hour for the garden to drain on time. If your garden still holds water after 48 hours, the soil is too slow, the garden is undersized for the drainage area, or the inlet is clogged with sediment, and you should fix the cause rather than live with the puddle.
What happens when my rain garden is bigger than 300 square feet?
Split it into smaller gardens. The extension guides say a single home rain garden should not exceed 300 square feet, because a larger garden is hard to dig and plant by hand. The calculator splits the area into the smallest number of gardens that keeps each one at or under 300 square feet: 480 square feet becomes two gardens of 240 square feet each, and 860 square feet becomes three gardens of about 286.7 square feet each. If the full size does not fit your yard, you can shrink it by up to 30 percent and still control about 90 percent of average runoff.
Page history
- — Pre-isBasedOn snapshot (YMYL authority, Nov 2026) (saleem891@gmail.com)
- — Pre-IA-remap snapshot: category population (live application 22 Nov 2026) (saleem891@gmail.com)
- — Published (saleem891@gmail.com)