Skip to content

Tree Height Calculator

Clinometer is the most accurate with a phone angle app. Shadow needs sun and level ground. Stick needs no tools at all.

All lengths are entered in this unit. The result shows both feet and meters.

Turn this on to use the sine method, with a laser rangefinder: two slope distances and two angles. It is the accurate method on slopes, leaning trees, and offset crowns.

Measure level from where you stand to the trunk. About one tree height back gives an angle near 45 degrees.

Sight the very top of the tree with a clinometer or a phone angle app. Read the angle up from level.

The height of your eyes above the ground. Leave blank for the default: 5.5 feet, or 1.7 meters.

Straight-line distance from your eye to the highest point, from a laser rangefinder.

Up from level is positive. If the top is below your eye level, enter a negative number.

Straight-line distance from your eye to the base of the trunk, where it meets the ground.

Down from level is negative, so a base below your eyes is a negative number, such as -5. A base above your eyes is positive.

Measure from the trunk to the tip of the shadow, on level ground.

Measure the stick's shadow at the same time as the tree's shadow.

Any straight stick or pole of known height, held vertical. Your own height works too: stand straight and measure your shadow.

Walk back until the top of the stick lines up with the top of the tree and the bottom lines up with the base, then measure to the trunk.

The height of your eyes above the ground. Leave blank for the default: 5.5 feet, or 1.7 meters.

Your tree height

How the answer was worked out

      This tool estimates a tree's height from the measurements you enter, for general guidance only. It is not a survey or a professional arborist's assessment. Field measurements carry error, especially on slopes and leaning trees, so check a height that affects safety, insurance, or a removal decision with a qualified arborist before acting on it.
      Stand back from the tree and measure the level distance to the trunk and the angle up to the top. The height is the distance times the tangent of the angle, plus your eye height: 50 feet back at 45 degrees with eyes 5.5 feet up gives a tree 55.5 feet tall. With no instruments, compare shadows: the tree is as many times as tall as its shadow is longer than a stick's shadow. On a slope, use the sine method with a laser rangefinder. Enter your measurements above for the height in feet and meters, with the full working.

      Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.

      How to use the Tree Height Calculator

      Every tree owner eventually asks the same question: how tall is that tree. The answer matters more often than people expect. A removal company quotes by height and by how close the tree stands to the house. An insurance adjuster wants to know whether a leaning tree can reach the roof. A gardener planning a new bed wants to know how much shade a tree will throw in five years. And a champion tree nomination starts with a height measurement that can stand up to checking. Climbing the tree with a tape is the direct way to find out, and it is also the dangerous way. This calculator gives you the answer from the ground, with nothing more than a tape measure and, for the most accurate method, a phone.

      There are three field methods in the calculator, plus a fourth for sloping ground. The clinometer method is the one foresters use: stand back from the tree, measure the angle up to the top, and let trigonometry do the rest. The shadow method needs no instruments at all, just sun and two shadows. The stick method needs nothing but a stick and your feet, and it is the one to teach a scout troop or a school class. On a slope, the clinometer method switches to the sine method, the technique the Eastern Native Tree Society developed for measuring big trees accurately on uneven ground. Pick the method that fits what you have with you, enter your measurements, and the calculator works out the height in feet and in meters, shows the full working, and tells you how much a small measuring error could move the answer.

      To get your result, follow these steps:

      1. Pick a method. Choose clinometer, shadow, or stick from the method menu. If you have a phone with an angle app, or a handheld clinometer, pick clinometer: it is the most accurate of the three on flat ground. If you have sun and level ground and no instruments, pick shadow. If you have nothing at all, pick stick. The form changes to show only the fields your method needs.
      2. Pick your units. Choose feet or meters. Every length you enter is in this unit, and the result shows both: the headline gives the height in your unit with the other unit in parentheses, and the cards show both figures side by side.
      3. Turn on slope correction if the ground slopes. The slope box appears only for the clinometer method. Turn it on when the ground between you and the tree is not level, or when the tree leans, or when the highest branch sits well out to one side of the trunk. The calculator switches to the sine method, which needs a laser rangefinder: two straight-line distances, one to the top and one to the base, and the angle to each. The sine method measures real points on the tree, so slopes, lean, and offset crowns do not fool it.
      4. Enter your measurements. For the clinometer method, enter the level distance from where you stand to the trunk, the angle up to the very top of the tree, and your eye height. Eye height is optional: leave it blank and the calculator uses 5.5 feet, or 1.7 meters, which is a typical adult eye height. For the shadow method, enter the length of the tree's shadow, the length of a stick's shadow measured at the same time, and the height of the stick. For the stick method, enter the distance to the trunk and your eye height. For the sine method, enter the two slope distances and the two angles, with the base angle negative when the base sits below your eye level.
      5. Read the full result, not just the headline. The headline gives the height in both units. The cards show the height above your eyes, the height in stories, and how far a 1-degree misread would move the answer. The guidance explains the result in plain language and compares the tree with familiar sizes. The warnings flag the measurements that need a second look, such as an angle that is too shallow or too steep, a shadow too short to measure well, or a height taller than any known living tree. The steps print the full working, so you can check every figure with your own arithmetic.

      The tool updates as you type, so you can try different numbers quickly. Try the example buttons under the form. The first is the classic clinometer example: 50 feet back, 45 degrees up, eye height 5.5 feet, a tree 55.5 feet tall. The second is a shadow example: a tree shadow 42 feet long against a 6-foot stick shadow, with a 5-foot stick, a tree 35 feet tall. The third is the sine method on a slope: 120 feet to the top at 40 degrees and 100 feet to the base at 5 degrees below level, a tree 85.8 feet tall. Each example shows a different shape of the answer, and each one prints its working in the steps.

      A note on what the calculator measures: tree height is the vertical distance from the ground at the base of the trunk to the highest living point of the crown. It is not the length of the trunk, which is longer on a leaning tree, and it is not the length of the longest branch. On flat ground the base is easy to find. On a slope, measure to the point where the trunk meets the ground halfway between the uphill side and the downhill side, which is the same mid-slope point the champion tree programs use. A dead top does not count: the highest living point is the top. If the tree has been topped, the highest living shoot is the top, and the height you measure is the height of the tree as it stands now, not the height it would have reached.

      How it works

      All four methods measure the same thing, the vertical height of the tree, and all four use the same idea: a triangle you can measure on the ground tells you a height you cannot reach. The methods differ in which triangle they use, and in what they assume about the tree. Understanding the assumption behind each method is what tells you when to trust it and when to switch to another one.

      The clinometer method: distance times tangent, plus eye height

      Stand at a known level distance from the trunk and sight the top of the tree with a clinometer, which is a small instrument that measures the angle you look up or down. A phone with a level or angle app does the same job: hold the long edge of the phone along your line of sight to the top and read the tilt. The angle, the distance, and the height above your eyes form a right triangle, and the tangent of the angle is the height above your eyes divided by the distance. So the height above your eyes is the distance times the tangent of the angle, and the whole tree is that plus your eye height. The formula is: height equals distance times tan(angle), plus eye height.

      Worked example: you stand 50 feet from the trunk, the clinometer reads 45 degrees to the top, and your eyes are 5.5 feet above the ground. The tangent of 45 degrees is exactly 1, so the height above your eyes is 50 times 1, which is 50 feet. Add the 5.5 feet of eye height, and the tree is 55.5 feet tall, which is 16.92 meters. The 45-degree case is the easiest to check in your head, and it is also the most accurate angle to measure at, for reasons the accuracy section below explains.

      Second worked example: you stand 60 feet from a pine, the clinometer reads 32 degrees, and your eyes are 5.5 feet up. The tangent of 32 degrees is 0.6249, so the height above your eyes is 60 times 0.6249, which is 37.5 feet. Add the 5.5 feet of eye height, and the tree is 43 feet tall. Notice that the eye height matters more on a short tree than on a tall one: on a 43-foot tree, forgetting the 5.5 feet of eye height would understate the height by about 13 percent. Measure your eye height rather than guessing it: stand against a wall, mark the height of your eyes, and measure the mark.

      The clinometer method has one assumption that matters: it assumes the highest point of the tree sits directly over the trunk, because the distance you measured is the distance to the trunk. On a straight, upright tree with a central leader, that is true, and the method is accurate. On a leaning tree, or on a spreading hardwood whose highest twig grows on a limb that reaches toward you, it is not true, and the method overstates the height. The overstatement is easy to see: if the top leans 10 feet toward you, the tangent calculation places that top above the trunk, and at a 45-degree sighting angle the answer comes out 10 feet too tall. The Eastern Native Tree Society has documented tangent-method overestimates of 5 to 20 meters on large hardwoods, which is 16 to 66 feet. When the top is not over the trunk, use the sine method instead.

      The table below shows the height above your eyes at several angles, standing 50 feet from the trunk. It is a quick check for field use: read your angle, find the row, and you have the height above your eyes before you add your eye height.

      Angle to the topTangentHeight above your eyes at 50 feet
      30 degrees0.57728.9 feet
      35 degrees0.70035.0 feet
      40 degrees0.83942.0 feet
      45 degrees1.00050.0 feet
      50 degrees1.19259.6 feet
      60 degrees1.73286.6 feet

      The table also shows why the angle matters so much. Between 30 and 45 degrees, the height grows gently. Past 45 degrees it grows fast: from 50 feet at 45 degrees to 86.6 feet at 60 degrees, standing in the same spot. A small error in a steep angle is a large error in height, which is why the calculator warns you when your angle is above 60 degrees and tells you to step back.

      The shadow method: similar triangles

      The shadow method is the oldest of the four, and it needs no instruments. It uses similar triangles: at any moment, the sun's rays hit the ground at the same angle everywhere, so the tree and its shadow form a triangle with exactly the same shape as the stick and its shadow. The ratio of height to shadow is the same for both. Measure the tree's shadow, measure a stick's shadow at the same time, and the tree's height is the stick's height times the ratio of the two shadows. The formula is: tree height equals the tree's shadow divided by the stick's shadow, times the stick's height.

      Worked example: the tree's shadow is 42 feet long, a 5-foot stick casts a 6-foot shadow at the same time, and the tree is 42 divided by 6, which is 7, times 5 feet, which is 35 feet tall. The stick can be anything straight and vertical with a known height: a yardstick, a broom handle, a fence post, or yourself standing straight. Your own height is a good stick, because you know it well and you are easy to stand vertical. Measure your own shadow from your heels to the tip of your head's shadow.

      The shadow method has three requirements. First, both shadows must be measured at the same time, because the sun moves and the shadows change length through the day. Measure one, then the other, within a few minutes. Second, the ground must be level, because a shadow falling on a slope is longer or shorter than the same shadow on flat ground. Third, the sun must be low enough to cast a clear shadow with a sharp tip. Near noon the shadows are short and hard to measure exactly, and a small error in a short shadow is a large error in the answer: if the stick's shadow is only 1 foot long, misreading it by 1 inch changes the ratio by about 8 percent. Morning or late afternoon, when shadows are long, is the time for this method. The calculator warns you when either shadow is under 1 foot, or under 0.3 meters, because below that length the measurement is hard to trust.

      The stick method: the 45-degree shortcut

      The stick method is the clinometer method with the angle fixed at 45 degrees, so no instrument is needed. Hold a straight stick vertically at arm's length, with as much stick above your fist as the distance from your fist to your eye. That makes the angle from your eye to the top of the stick exactly 45 degrees. Walk toward or away from the tree until the top of the stick lines up with the top of the tree and the bottom of the stick, your fist, lines up with the base of the tree. At that point you are looking at the top of the tree at 45 degrees, and the tangent of 45 degrees is 1, so the height above your eyes equals your distance from the trunk. Measure the distance, add your eye height, and you have the tree. The formula is: height equals distance plus eye height.

      Worked example: you walk back until the stick lines up, measure 40 feet to the trunk, and your eyes are 5.5 feet up. The tree is 40 plus 5.5, which is 45.5 feet tall. The method is quick and it needs nothing you do not already have, which is why foresters teach it as a field check and why it is the standard method for school groups. It is also the least precise of the three, because judging when the stick lines up exactly is a matter of the eye, and a 1-degree error in judging the 45-degree angle moves the answer by about 1.4 feet at 40 feet. Use it for a quick estimate, and check the answer with the clinometer method when the number matters, such as a removal quote or a falling-distance check.

      There is a common variation that skips the stick: walk back from the tree until you can see the top of the tree by looking up at 45 degrees, which you judge by holding your arm out at 45 degrees or by bending forward and looking between your legs. The geometry is the same, and the accuracy is about the same. However you set the 45 degrees, the same rule holds: the distance equals the height above your eyes, plus your eye height.

      The sine method: two distances, two angles, no assumptions

      The sine method is the accurate method for difficult trees, and it is the one the calculator switches to when you turn on slope correction. It needs a laser rangefinder, the kind that measures the straight-line distance to a point and reads the angle to it, and a clinometer. You measure the straight-line distance from your eye to the top of the tree and the angle to the top, then the straight-line distance to the base and the angle to the base. Each measurement gives a vertical piece: the top sits the top distance times the sine of the top angle above your eyes, and the base sits the base distance times the sine of the base angle below your eyes, when the base angle is below level. Add the two pieces and you have the height. The formula is: height equals the top distance times sin(top angle), plus the base distance times sin(base angle below level).

      The method was developed by the Eastern Native Tree Society and described for foresters by Don Bragg of the USDA Forest Service, Southern Research Station, in the Southern Journal of Applied Forestry in 2008. Bragg's paper gives the formula in its standard form, with the two slope distances and the two angles, and shows it tested on mature pines in Arkansas, where it agreed with direct tape measurements on trees up to 50 meters tall. The American Forests Champion Trees Measuring Guidelines Handbook calls the sine method the simplest and most direct way to measure tree height from the ground when the top and base can be seen by the laser, and it is the method the national champion tree program prefers.

      Worked example: the laser reads 120 feet to the top at 40 degrees above level, and 100 feet to the base at 5 degrees below level. The sine of 40 degrees is 0.6428, so the top sits 120 times 0.6428, which is 77.1 feet above your eyes. The sine of 5 degrees is 0.0872, so the base sits 100 times 0.0872, which is 8.7 feet below your eyes. The tree is 77.1 plus 8.7, which is 85.8 feet tall, or 26.15 meters. Note that no eye height appears in the calculation: the sine method measures the top and the base against your eye level, so the eye height cancels out.

      The handbook's own worked example shows the same arithmetic on a bigger tree: 175.5 feet to the top at 38.9 degrees, and 115 feet to the base at 7.7 degrees below level. The top sits 110.2 feet above the eyes, the base sits 15.4 feet below them, and the tree is 125.6 feet tall. The sine method has one great advantage over the tangent method: it measures real points on the tree, so it does not matter whether the top sits over the trunk, whether the trunk leans, or whether the ground slopes. It cannot overestimate the height the way the tangent method can, because each term is the vertical piece of a real measured line. Its only requirement is that you can see the true top and the true base with the laser, which can be hard in a thick canopy or on a windy day when the top is moving.

      How accurate is each method?

      No ground method is exact. Every one of them turns small measuring errors into height errors, and the size of the error depends on the method and on where you stand. The honest way to use any of them is to know how big the error can be, and to set up the measurement so the error is small. The calculator helps by showing, on every clinometer, sine, and stick result, how far a 1-degree misread would move the answer. That number is the heart of accuracy for angle methods, and it follows a simple rule: the error per degree equals the distance times the square of the secant of the angle, times pi over 180. In plain terms, the error grows with the distance and grows fast as the angle gets steep.

      The table below shows the error from a 1-degree misread at several angles, standing 50 feet from the trunk. At 30 degrees a 1-degree error moves the answer by 1.16 feet. At 45 degrees it moves it by 1.75 feet. At 60 degrees it moves it by 3.49 feet, and at 70 degrees by 7.46 feet. Standing closer helps in proportion: from 30 feet, a 1-degree error at 45 degrees moves the answer by 1.05 feet, and at 70 degrees by 4.48 feet. The pattern is the reason for the oldest rule in tree measuring: stand back about one tree height, so the angle is near 45 degrees, where the error is small and the top is easy to see. The calculator warns you below 30 degrees, where you are standing too far away to see the top clearly, and above 60 degrees, where you are standing too close and the error is growing fast.

      Angle to the topError per 1 degree at 50 feetError per 1 degree at 30 feet
      30 degrees1.16 feet0.70 feet
      45 degrees1.75 feet1.05 feet
      60 degrees3.49 feet2.09 feet
      70 degrees7.46 feet4.48 feet

      The distance matters too, and in the opposite direction from what people expect. A longer distance makes the angle error bigger, but it makes the distance error smaller in proportion: misreading the distance by 1 foot at 50 feet is a 2 percent error, and the height error is about 2 percent of the height above your eyes. Pacing the distance is the weakest link in most measurements. A pace is rarely as even as its owner thinks, and a slope makes it worse, because a pace measured along a slope is longer than the level distance the formula wants. Use a tape, or a measuring wheel, or a laser rangefinder, and measure level. If the ground slopes, measure the slope distance and the slope angle and work out the level distance, or switch to the sine method, which takes the slope distance directly. Our Slope Calculator works out the slope of the ground between you and the tree from a rise and a run, which is the first step in correcting a slope measurement by hand.

      The shadow method has a different error shape. Its error comes from the shadow lengths, and it is worst when the shadows are short. If the stick's shadow is 6 feet long and you misread it by 1 inch, the ratio changes by about 1.4 percent, and the height changes by the same proportion. If the stick's shadow is 1 foot long, the same 1-inch misread changes the ratio by about 8 percent. The tree's shadow has the same effect in the other direction. Long shadows, measured carefully to the tip, are what make this method good. The tip of the tree's shadow is the hardest part to find: the shadow of the topmost twig is faint, and on a windy day it moves. Mark it with a stake and measure to the stake.

      The sine method's error comes from the two angles and the two distances, and it is the smallest of the four when the equipment is good. A laser rangefinder that reads distance to a foot and angle to 0.1 degrees gives a height good to about a foot on a 100-foot tree, which is why the champion tree programs accept it. Its weakness is not arithmetic but identification: the laser must hit the true top, and on a broad crown the true top can be hard to find from any one spot. Bragg's 2008 paper tells the story of a loblolly pine where the obvious top seen from 30.5 meters turned out to be a subordinate branch, and the true top only showed itself from 78 meters away. Walk around the tree, measure from two or three directions, and take the tallest reading: the sine method cannot overestimate, so the tallest careful reading is the closest to the truth.

      For all four methods, the best accuracy check is a second measurement. Measure the same tree by two methods, or from two directions, or on two days, and compare. If the clinometer and the shadow methods agree within a few feet, both are probably right. If they disagree by more than about 10 percent, one of the measurements is wrong: check the distance first, then the angle, then whether the top you sighted is really the top. And measure in still air when you can: a top swaying in the wind is a moving target, and no method reads a moving target well.

      Which method should you use?

      The right method depends on what you have with you, what the ground is like, and how much the answer matters. The table below compares the four methods on the things that decide the choice. There is no single best method: the sine method is the most accurate, but it needs a laser rangefinder, and the stick method is the least accurate, but it needs nothing at all and it is the one you can use anywhere, in any weather, with no preparation.

      MethodWhat you needBest forWatch out for
      ClinometerPhone angle app or clinometer, tapeMost trees on flat groundLeaning trees and offset crowns
      ShadowSun, a stick, a tapeOpen ground with no instrumentsSlopes, clouds, short shadows
      StickA stick, a tapeQuick estimates, teachingJudging the 45 degrees by eye
      Sine (slope)Laser rangefinder, clinometerSlopes, lean, champion treesFinding the true top in a thick crown

      For a removal quote or an insurance question, use the clinometer method on flat ground or the sine method on a slope, and measure twice. For a quick check before you plant, the stick method is enough. For a school lesson, the shadow method is the best teaching tool there is: it makes similar triangles visible, it needs no equipment the school does not already have, and every student can measure the same tree and compare answers. For a champion tree nomination, use the sine method with a laser rangefinder, measure from several directions, and keep your notes: the nomination asks how the height was measured, and the sine method with a laser is the answer the program wants to hear.

      How tall should your tree be?

      A height measurement is more useful when you know what is normal for the species. A 40-foot white oak is a young tree with decades of growth ahead of it. A 40-foot red maple is close to full grown. A 100-foot tulip tree is a fine mature specimen, and a 100-foot eastern white pine in a yard is a tree that has outgrown its planting spot. The table below gives typical mature heights for eight common North American trees, as landscape trees in a yard or park. The figures come from The Morton Arboretum and from university and conservation district tree lists, and they are ranges, not single numbers, because a tree's mature height depends on soil, water, light, and room to grow.

      TreeTypical mature heightNotes
      White oak50 to 80 feetSlow growing, very long lived
      Sugar maple60 to 75 feetForest trees reach 100 feet or more
      Red maple40 to 60 feetSmaller than most maples
      Silver maple50 to 70 feetFast growing, weak wood
      Eastern white pine50 to 80 feetForest trees reach 100 feet or more
      Tulip tree70 to 120 feetTallest eastern hardwood
      American sycamore75 to 100 feetOne of the largest eastern trees
      Loblolly pine60 to 100 feetFast growing southern pine

      Two things about these ranges are worth knowing. First, sources disagree by 10 to 20 feet on most species, and the disagreement is honest: landscape trees in yards grow shorter than forest trees of the same species, because a yard tree spreads wide instead of racing upward for light, and because yard trees are often pruned, topped, or damaged by storms. A white oak listed at 50 to 80 feet in a landscape guide can reach 100 feet in a forest. Second, a tree that is well short of its mature height is usually a young tree, but it can also be a stressed tree: drought, poor soil, root damage, and repeated topping all hold a tree short. If your measurement is far below the range for a tree you know is old, look at the crown and the roots before you conclude the measurement is wrong.

      At the far end of the scale sits Hyperion, a coast redwood in Redwood National Park in California, the tallest known living tree. Guinness World Records lists it at 116.07 meters, which is 380 feet 10 inches, measured in 2019, and the most recent measurement, in 2026, puts it at 116.22 meters, or 381.3 feet. It was discovered in 2006 and measured by climbing and dropping a tape from the top, which is the only method that gives a height to the inch on a tree that tall. The tree is 600 to 800 years old, and its exact location is kept secret to protect it. The calculator warns you when your measurement passes 382 feet, because past that point you are taller than the tallest known living tree, and the likeliest explanation is a misread angle or distance, not a world record. The theoretical ceiling for tree height, set by how high a tree can lift water, is generally put between 400 and 427 feet, so even the tallest trees have a limit, and your measurement should sit well below it.

      Height is also one third of a champion tree score. American Forests scores champion trees by a points formula: trunk circumference in inches, plus height in feet, plus one quarter of the average crown spread in feet. A post oak with a 144-inch circumference, a 70-foot height, and an 80-foot average crown spread scores 144 plus 70 plus 20, which is 234 points. The national champion northern red oak, measured in 2020, scored 455 points: 337 inches around, 92 feet tall, with an average crown spread of 103 feet. The circumference is measured at 4.5 feet above the ground, which foresters call diameter at breast height, or DBH. If your tree's height is near the top of its species range, measure the trunk and the crown too, and check the current champion for the species: a nomination starts with three measurements, and the height is the one this calculator gives you.

      What to do with the height

      A tree's height is a working number, not a curiosity. The most common use is a removal quote: tree services price by height, by trunk diameter, and by how close the tree stands to buildings and power lines, and a height figure from your own measurement lets you check whether two quotes are pricing the same tree. Measure before you call, and tell the company the height and the distance to the nearest structure. A tree that can reach the house when it falls costs more to remove than one that can fall clear, because the crew has to take it down in pieces.

      Falling distance is the second use, and the simplest: a tree can fall about its own height from the trunk, so a 60-foot tree can reach anything within 60 feet. That rule of thumb is the one insurers and arborists use for a first check, and it is conservative enough to be useful: a tree rarely falls at full length in the direction of its lean, but the lean is where it will go if it goes. Measure the height, measure the distance to the house, the fence, the power line, and the neighbor's roof, and you know which trees are a risk and which are not. If the height is close to the distance, get an arborist to look at the tree: lean, root damage, and dead wood change the risk more than height alone.

      Planting decisions are the third use. A tree's mature height tells you where it can go: under a power line, only trees that mature under 25 feet are safe, which rules out every tree in the table above. Near a house, a tree should stand at least its mature height away from the foundation if you want no pruning, no gutter cleaning, and no root trouble, though in practice most yard trees stand closer and are pruned to fit. When you plant a new tree, the mature height also sets the spacing from its neighbors: two trees that will each reach 60 feet need 40 to 60 feet between them, or they will crowd each other and grow tall and thin. Our Tree Planting Calculator plans spacing and hole size for a new tree, and our Orchard Planner Calculator lays out fruit trees with room to grow.

      Shade planning is a quieter use. A tree's shadow at noon is its height divided by the tangent of the sun's elevation, which at mid-latitudes in summer puts the noon shadow at about a third of the height, so a 40-foot tree throws about 12 feet of shade at midday in June, and much more in the morning and evening. If you are placing a vegetable garden, a patio, or a solar panel, the tree's height and its direction from the spot tell you how much sun the spot will lose. Our Garden Watering Calculator helps with the other half of the shade question, how much water the plants under the tree will need, and our Pruning Calendar shows when to prune the tree you just measured, so the work is done in the right season.

      Finally, height is a record worth keeping. Measure a young tree once a year, in the same month, and you have a growth record that tells you whether the tree is thriving. A healthy young shade tree grows 1 to 3 feet a year, and a fast grower such as a tulip tree or a loblolly pine can grow 2 to 3 feet a year in good soil. A tree that stops growing, or that loses height to a dead top, is a tree asking for attention. Write the date and the method on the record: a clinometer reading and a stick reading are not directly comparable, and a record that mixes methods will show jumps that are really method changes.

      Sources

      The methods in this calculator come from the forestry literature, and the figures in the article come from the publishers named below. All sources were re-checked on 20 November 2026.

      • Don C. Bragg, An Improved Tree Height Measurement Technique, Southern Journal of Applied Forestry 32(1), 2008, USDA Forest Service, Southern Research Station: the sine method in its standard form, tested on mature pines in Arkansas, with the tangent method's assumptions and the Eastern Native Tree Society's documented overestimates of 5 to 20 meters on large hardwoods. Read the paper (PDF).
      • American Forests, Champion Trees Measuring Guidelines Handbook, 2014, via the National Champion Tree Program: the sine method as the preferred height method, the points formula of trunk circumference in inches plus height in feet plus one quarter of the average crown spread in feet, and the 4.5-foot measuring height for circumference. Tree measurements and points calculation. See also the American Forests guide to champion tree hunting: How to bag yourself the next big tree.
      • Guinness World Records, Tallest tree living: Hyperion, a coast redwood in Redwood National Park, California, 116.07 meters (380 feet 10 inches) in 2019, discovered 25 August 2006. Tallest tree living.
      • The Morton Arboretum, tree profiles: mature heights for white oak (50 to 80 feet), sugar maple (60 to 75 feet), red maple (40 to 60 feet), and silver maple (50 to 70 feet), and the rule that only trees maturing under 25 feet suit planting under utility lines. White oak profile.
      • Mississippi State University Extension, 4-H Forestry Project No. 2: Big Tree Contest: the points formula worked through on a post oak, 144 inches plus 70 feet plus one quarter of 80 feet, for 234 points. 4-H Big Tree Contest.
      • Technical Math: Applications for the Environmental Sciences, OpenWA Pressbooks: the tangent method worked through with the angles to the top and the bottom of the tree and the level distance. Right triangle applications.
      • How to measure tree height: the sine method, not tangent: the handbook's worked example, 175.5 feet at 38.9 degrees and 115 feet at 7.7 degrees below level, giving 125.6 feet, and the national champion northern red oak at 455 points. The sine method, not tangent.

      Frequently asked questions

      How do you measure the height of a tree without climbing it?

      Stand back from the tree, measure the level distance to the trunk and the angle up to the top with a clinometer or a phone angle app, and work out the height as the distance times the tangent of the angle, plus your eye height. Standing 50 feet back at 45 degrees with eyes 5.5 feet up gives a tree 55.5 feet tall. Two other methods need no instruments: the shadow method compares the tree's shadow with a stick's shadow, and the stick method uses a 45-degree sight line so the distance equals the height above your eyes. On a slope, use the sine method with a laser rangefinder instead.

      What is the most accurate way to measure tree height from the ground?

      The sine method with a laser rangefinder and a clinometer is the most accurate, and it is the method the American Forests champion tree program prefers. It measures the straight-line distance and the angle to the top and to the base, and adds the two vertical pieces, so it works on slopes, leaning trees, and crowns whose highest twig sits out to one side. The tangent clinometer method is nearly as accurate on a straight, upright tree on flat ground, but the Eastern Native Tree Society has documented tangent-method overestimates of 5 to 20 meters on large hardwoods whose tops lean toward the observer. A laser rangefinder that reads distance to a foot and angle to 0.1 degrees gives a height good to about a foot on a 100-foot tree.

      How does the shadow method work?

      The shadow method uses similar triangles: the sun's rays hit the ground at the same angle everywhere, so the tree and its shadow form a triangle with exactly the same shape as a stick and its shadow. Measure the tree's shadow, measure a stick's shadow at the same time, and the tree's height is the stick's height times the ratio of the two shadows. A tree shadow 42 feet long against a 6-foot stick shadow, with a 5-foot stick, gives 42 divided by 6, which is 7, times 5 feet, which is 35 feet. Measure both shadows within a few minutes of each other, on level ground, in the morning or late afternoon when shadows are long.

      What is the stick method for measuring tree height?

      Hold a straight stick vertically at arm's length, with as much stick above your fist as the distance from your fist to your eye, which sets the angle to the top of the stick at 45 degrees. Walk back until the top of the stick lines up with the top of the tree and your fist lines up with the base, then measure the distance to the trunk and add your eye height. At 45 degrees the tangent is 1, so the height above your eyes equals the distance: 40 feet back with eyes 5.5 feet up gives a tree 45.5 feet tall. It is the least precise of the three methods, because judging the lineup by eye is approximate, so use it for a quick estimate and check the answer with the clinometer method when the number matters.

      How do you measure tree height on a slope?

      Use the sine method, which takes slope distances directly and needs no level ground. With a laser rangefinder, measure the straight-line distance to the top and the angle to the top, then the straight-line distance to the base and the angle to the base. The top sits the top distance times the sine of the top angle above your eyes, and the base sits the base distance times the sine of the base angle below your eyes. A laser reading of 120 feet to the top at 40 degrees and 100 feet to the base at 5 degrees below level gives 77.1 feet above your eyes and 8.7 feet below them, a tree 85.8 feet tall. The tangent method can be corrected for a slope by converting the slope distance to a level distance, but the sine method is simpler and more accurate.

      How tall is a typical tree?

      Most yard trees stand between 30 and 60 feet tall, and a mature shade tree in a yard reaches 60 to 100 feet. White oak matures at 50 to 80 feet, sugar maple at 60 to 75 feet, red maple at 40 to 60 feet, eastern white pine at 50 to 80 feet, tulip tree at 70 to 120 feet, American sycamore at 75 to 100 feet, and loblolly pine at 60 to 100 feet. Forest trees of the same species often grow taller than yard trees, because they race upward for light instead of spreading wide. The tallest known living tree is Hyperion, a coast redwood in California, measured at 381.3 feet in 2026.

      How accurate is a phone clinometer app?

      A phone angle app is accurate enough for most purposes when the phone is held steady and the app is calibrated on a level surface first, and a 1-degree error is a small height error when you stand at the right distance. From 50 feet, a 1-degree misread moves the answer by 1.75 feet at a 45-degree angle, 3.49 feet at 60 degrees, and 7.46 feet at 70 degrees, which is why you should stand back about one tree height so the angle is near 45 degrees. Hold the phone's long edge along your line of sight, and take two readings and average them. A handheld clinometer is the better tool when the number matters, and a laser rangefinder with a built-in tilt sensor is better still.

      What is tree height used for?

      Tree height prices a removal, because tree services quote by height and by how close the tree stands to buildings and power lines. It sets the falling distance, because a tree can fall about its own height from the trunk, so a 60-foot tree can reach anything within 60 feet. It places new plantings, because a tree should stand at least its mature height from a house and 40 to 60 feet from another large tree, and only trees maturing under 25 feet suit planting under a power line. It is one third of a champion tree score, with trunk circumference and crown spread, under the American Forests points formula. And it tracks growth: a healthy young shade tree grows 1 to 3 feet a year, so a yearly measurement tells you whether the tree is thriving.