3D Print Cost Calculator
Estimated cost per print
Suggested selling price
Where the money goes
Same print, different material
The same print volume in PLA, PETG, and ABS, at the price per kilogram you entered, so the comparison isolates the density effect: the length is the same for every material, and only the weight changes. To compare at each material's own price, run the calculator once per material with its own price per kilogram.
Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.
How to use the 3D Print Cost Calculator
How much does it cost to 3D print something? Most answers count the filament and stop there, which gets you about half the real number. This 3D print cost calculator counts the whole print: filament, electricity, printer wear, and the prints that fail, then turns that full cost into a suggested selling price at the markup you choose. It also compares the same print in PLA, PETG, and ABS, so you can see what the material choice does to the price before you slice.
- Pick the material. PLA, PETG, ABS, TPU, or Nylon. Each card shows the density the calculator uses: 1.24 g per cubic cm for PLA, 1.27 for PETG, 1.04 for ABS, 1.21 for TPU, and 1.14 for Nylon (PA6). Density is what turns a length of filament into a weight, and a weight into a length, so it sits behind every number on the page.
- Enter how much filament the print uses, in grams or meters. Your slicer reports both after slicing: Cura, PrusaSlicer, Bambu Studio, and OrcaSlicer all show the filament weight and length for the sliced model. Use the total including supports, brims, rafts, and purge lines, not the model weight alone. If your slicer only gives meters, switch to meters mode and pick the diameter, 1.75 mm or 2.85 mm, and the calculator converts the length to grams with the material density.
- Enter what the filament cost. Either the price per kilogram, or the spool price and the spool's net weight in grams. The $20 starting price is a typical 2026 PLA price: makers list PLA at $18.99 to $19.99 per kg (FirstLayerLab, September 2026). Enter what you actually paid, including shipping, and use the net filament weight: a "1 kg" spool holds 1,000 g of plastic, and the spool itself is extra.
- Enter the print time in decimal hours. Three hours and 30 minutes is 3.5. The slicer estimate is the number to use. Leave the time at 0 if you only want the filament cost: electricity and wear both scale with hours, so they drop to zero.
- Set the printer power. Pick your printer from the preset list, or type the average watts yourself. Use the average draw while printing, not the peak on the spec sheet: a Bambu Lab P1S peaks near 1,000 W while the bed heats and averages about 105 W while printing PLA, according to Bambu Lab's own published measurements. The presets use those published figures.
- Enter your electricity price. The $0.18 starting rate is the US average residential price, 18.16 cents per kWh (EIA, August 2026). Your own bill is the better number: in August 2026 the residential average ran from 13.31 cents in North Dakota to 47.18 cents in Hawaii, so the same print costs three times as much to power in one state as in another.
- Set the failure rate and the printer wear. Ten percent is the failure rate most pricing guides use as a starting point: a well-tuned printer runs near 5 percent, a busy shop on long unattended jobs nearer 15 percent. For wear, divide your printer price by the hours you expect it to last, 3,000 to 5,000 hours is realistic for a consumer machine, and add a little for nozzles and build plates. The $0.25 starting point is PrintCost.site's default.
- Set the markup for the selling price. Markup is added on top of cost: a 50 percent markup prices a $2.00 print at $3.00, which is a 33.3 percent margin on the selling price. Common markups run from 20 percent to 100 percent. Set it to 0 if you only want the cost.
- Read the full result. The headline is the estimated cost per print including failed prints. Below it you get the suggested selling price with the profit and margin spelled out, a stacked bar showing where the money goes, the same print priced in PLA, PETG, and ABS, and the detail lines: grams and meters used, cost per gram and per meter, kilowatt-hours, prints per spool, and cost per gram and per hour.
This calculator is one of the free tools on Tools Elite. Every figure on this page comes from a published source listed at the bottom: the EIA for electricity prices, Bambu Lab's published measurements for printer power, maker store prices for filament, and the pricing guides that set the conventions for wear, failures, and markup, each accessed 20 November 2026. If you print on paper too, our Printer Cost Per Page Calculator does the same full-cost math for ink and toner. A long print is also the print most worth protecting from a power cut: our UPS Runtime and Size Calculator sizes a battery backup that keeps the printer running. The calculator gives estimates for general guidance, not a quote for any one job, so always check the manufacturer's specifications for the filament and printer you use.
How it works
The calculator works in six steps: it turns your filament amount into grams, works out the price per gram, prices the filament, the electricity, and the wear, spreads the cost of failed prints across the good ones, and then applies your markup to give a selling price.
Step 1: turn the filament amount into grams. If you enter grams, that is the weight. If you enter meters, the calculator treats the filament as a cylinder: cross-section area is pi times the radius squared, volume is area times length, and weight is volume times density. For 1.75 mm filament the cross-section is 0.02405 square cm, so one meter holds 2.405 cubic cm. In PLA at 1.24 g per cubic cm, one meter weighs 2.98 g. For 2.85 mm filament the cross-section is 0.06379 square cm, so one meter of PLA weighs 7.91 g.
Step 2: work out the price per gram. The spool price divided by the spool weight in grams. A $20 spool of 1,000 g costs $0.02 per gram. In per-spool mode the calculator first works out the price per kilogram, so a $22 spool of 750 g becomes $29.33 per kg, or $0.0293 per gram, which is why small spools look cheap on the shelf and cost more per print. The price per meter follows from the grams per meter: at $0.02 per gram, PLA costs about $0.0597 per meter.
Step 3: price the filament, the electricity, and the wear. Filament cost is grams times price per gram. Electricity is watts divided by 1,000, times hours, times the price per kWh. Wear is hours times your wear rate per hour. These three add up to the plain cost of the print, before failures.
Step 4: spread the failed prints across the good ones. If a fraction f of your prints fail, only 1 minus f of the prints you start ever ship, so each good print must carry 1 divided by (1 minus f) of the plain cost. At a 10 percent failure rate that is 1 divided by 0.9, about 11.1 percent more than the plain cost. This is the exact expected-cost math, used by CalcGoose and Price Profit Tools. Some guides add the rate instead, which at 10 percent gives 10 percent more rather than 11.1 percent: on a $1.80 print that is $1.98 against $2.00. The difference is small at low rates and grows as the rate rises: at 50 percent the divide method doubles the cost and the add method adds only half.
Step 5: apply the markup. Selling price is the cost with failures times 1 plus the markup. A 50 percent markup on a $2.00 cost gives $3.01 (the extra cent is rounding: the unrounded cost is $2.0044). Profit is the selling price minus the cost with failures. The implied margin is the profit divided by the selling price: a 50 percent markup is a 33.3 percent margin.
Step 6: compare the same print in PLA, PETG, and ABS. The comparison takes the volume of your print, which is fixed by the model, and prices it in each of the three materials at the price per kilogram you entered. The length is the same for every material, because the volume and the diameter are the same, and only the weight changes with density. The comparison isolates the density effect: to compare at each material's own price, run the calculator once per material with its own price per kilogram.
Worked example 1: a 50 g PLA print. Take 50 g of PLA at $20 per kg, 3 hours on a 100 W printer at $0.18 per kWh, wear at $0.25 an hour, a 10 percent failure rate, and a 50 percent markup. Filament is 50 times $0.02, $1.00. Electricity is 0.1 kW times 3 hours, 0.3 kWh, times $0.18, $0.05. Wear is 3 times $0.25, $0.75. The plain cost is $1.80. With failures it is $1.80 divided by 0.9, $2.00. The selling price is $2.00 times 1.5, $3.01. Profit is $1.00, a 33.3 percent margin. The print uses 16.76 m of filament, and a 1 kg spool gives 20 of them.
Worked example 2: an 85 g PLA print. Take 85 g of PLA at $20 per kg, 6.5 hours on a 120 W printer at $0.17 per kWh, wear at $0.25 an hour, a 10 percent failure rate, and a 50 percent markup. Filament is 85 times $0.02, $1.70. Electricity is 0.12 kW times 6.5 hours, 0.78 kWh, times $0.17, $0.13. Wear is 6.5 times $0.25, $1.63. The plain cost is $3.46. With failures it is $3.46 divided by 0.9, $3.84. The selling price is $3.84 times 1.5, $5.76. Profit is $1.92, a 33.3 percent margin. The print uses 28.5 m of filament, and a 1 kg spool gives 11 of them. Notice how wear overtakes filament on a long print: the machine time, not the plastic, is what a 6.5-hour print really costs.
What the calculator does not do. It does not include your hands-on time, packaging, shipping, or marketplace fees, so the selling price is a starting point, not a final price: add those before you list anything. It does not cover resin printing, which has a different cost shape and is covered in the resin section below. It does not store prices: the $20 per kg and $0.18 per kWh starting points are labeled typical values with their sources and dates, and you should replace them with your own numbers.
What goes into the cost of a 3D print
Four things make up the cost this calculator counts. Each one is small on its own, and each one is the line a different kind of seller forgets.
Filament is the visible cost, and usually the biggest for short prints. It is grams times price per gram, and the grams figure must include everything the printer extrudes: the model, the supports, the brim or raft, the skirt, and the purge lines. Supports alone can add 10 to 20 percent to the filament weight, and on a model with heavy overhangs a 100 g model can easily need 30 g of supports. A slicer estimate that reports only the model weight understates the cost by 10 to 40 percent depending on the geometry. The honest grams number is the slicer total including supports, or the weighed spool difference before and after the print. Multicolor prints are the extreme case: on small parts the purge filament can weigh more than the part itself.
Electricity is the cost people overestimate, and it is usually pennies. A desktop FDM printer averages about 50 to 250 watts while printing, and the heated bed does most of the work. At 100 W and $0.18 per kWh, an hour of printing costs 1.8 cents, and a 10-hour print costs 18 cents. Even a 40-hour print at 150 W costs about $1.08 in power. Electricity only becomes a real line on very long prints, on heated-chamber machines running engineering plastics, or where power is expensive: in Hawaii at 47.18 cents per kWh, the same 10-hour print costs 47 cents. The section below gives the measured wattages for popular printers.
Printer wear is the cost people forget, and it grows with print time. A printer is a machine that wears out: nozzles, belts, PTFE tubes, build plates, and eventually the printer itself. Spread the purchase price over the hours the machine will run. Desktop machines are commonly quoted at 3,000 to 10,000 hours of useful life, with 5,000 hours the usual middle figure. An $800 printer over 5,000 hours costs $0.16 an hour in depreciation alone. A $600 printer over 4,000 hours costs $0.15 an hour, and adding $0.15 an hour for nozzles, plates, and parts brings the machine cost to $0.30 an hour. A $400 printer over 4,000 hours costs $0.10 an hour. The calculator's $0.25 starting point sits inside that published range. On a 3-hour print wear is $0.75; on a 40-hour print it is $10.00, which is why long prints cost far more than their filament suggests.
Failed prints are the cost people refuse to count, and they are real money. A print that fails at 80 percent has consumed 80 percent of its filament, its power, and its wear for nothing. Over a run of prints, a failure rate of one in ten adds about 11.1 percent to the cost of each good print, by the divide method this calculator uses. GrandpaCAD puts the realistic range at 5 to 15 percent: 5 percent is a well-tuned machine you babysit, 15 percent is a busy shop running long unattended jobs. The right number is the one you actually measure: count total prints and failed prints over a month or two, and use your own rate. New materials and complex multicolor jobs deserve a higher number than a familiar PLA print.
Your time is the fifth cost, and this calculator deliberately leaves it out. Slicing, setup, support removal, sanding, painting, packing, and customer messages are hands-on work, and on small prints they dominate: in Price Profit Tools' worked example of a 45 g phone stand, labor is $8.33 of an $11.81 total cost, about 70 percent. In GrandpaCAD's example of a 50 g part, 15 minutes of hands-on work at $20 an hour is $5.00 of a $7.34 total. The calculator leaves labor out because your rate and your minutes are yours to set, and a default would be a guess dressed as a fact. Add your time on top of the calculator's total before you set a final price, and remember that print time is machine time, not labor: you are not sitting there watching it.
Filament densities and prices by material
Density decides how much a print weighs, and price per kilogram decides what that weight costs. The table below puts both together for the five materials in the calculator, with the grams per meter and meters per kilogram for 1.75 mm filament worked out from the same formula the calculator uses.
| Material | Density | Grams per meter (1.75 mm) | Meters per kg (1.75 mm) | Typical price per kg |
|---|---|---|---|---|
| PLA | 1.24 g per cubic cm | 2.98 g | About 335 m | $18.99 to $19.99 |
| PETG | 1.27 g per cubic cm | 3.05 g | About 327 m | $16.99 to $24.99 |
| ABS | 1.04 g per cubic cm | 2.50 g | About 400 m | $18.99 to $19.99 |
| TPU | 1.21 g per cubic cm | 2.91 g | About 344 m | $38.99 to $49.99 |
| Nylon (PA6) | 1.14 g per cubic cm | 2.74 g | About 365 m | $66.65 to $79.99 |
Prices are a September 2026 snapshot, not live prices. FirstLayerLab read them on 29 September 2026 from the makers' own US online stores, for 1 kg of 1.75 mm filament with a spool: Bambu Lab PLA Basic at $18.99 (refill $15.99), Polymaker PolyLite PLA at $19.99, Bambu Lab PETG Basic at $16.99, Bambu Lab ABS at $18.99, Bambu Lab TPU for AMS at $38.99, Polymaker PolyFlex TPU95 at $49.99, and nylon from $66.65 (Polymaker PolyMide CoPA, $49.99 per 750 g) to $79.99 (Bambu Lab PA6-CF). Other guides agree on the shape: PrintingXYZ puts a 1 kg spool of PLA, PETG, or ABS at $18 to $35 in 2026, TopSTL puts PLA at $18 to $24 and TPU at $35 to $50, and NestOfTools prices PLA at $25, PETG at $28, ABS at $26, and TPU at $35 per kg. Prices change often, and each store runs its own bulk and bundle deals, so enter the price you paid.
The same print weighs a different amount in each material. Because a slicer extrudes a volume of plastic, not a weight, the same model in ABS weighs about 16 percent less than in PLA (1.04 divided by 1.24), and in PETG about 2.4 percent more (1.27 divided by 1.24). That is why the comparison in the calculator shows the same volume in three materials: a 50 g PLA print is 51.2 g in PETG and 41.9 g in ABS, and at the same price per kilogram the ABS version costs the least in filament. But the material price usually matters more than the density: nylon costs three to four times as much per kilogram as PLA, so a nylon print costs far more even though it weighs less.
Densities are typical values, and sources disagree at the edges. PLA at 1.24, PETG at 1.27, ABS at 1.04, and TPU at 1.21 are the standard reference values used by Bitfab, Mogerio, STLtoMP4, and the filament calculators that publish their tables. The disagreements are real and worth knowing. PETG: Bambu Lab's own data sheet for PETG Basic gives 1.25, and Polymaker's technical data table gives 1.25 for PolyLite PETG, against the standard 1.27, a difference of about 1.6 percent. PLA: Polymaker's table gives 1.17 for PolyLite PLA, against the standard 1.24, a difference of about 6 percent. Nylon: STLtoMP4 gives a range of 1.01 to 1.14 depending on type, PA12 low and PA6 high, Polymaker gives 1.12 for its CoPA nylon, and Bitfab gives 1.52, an outlier that likely reflects a filled or glass-reinforced grade rather than plain nylon. This calculator uses the standard values, 1.24, 1.27, 1.04, 1.21, and 1.14 for PA6, and the nylon note in the results says so plainly. Filled filaments change the picture further: wood, metal powder, and carbon fiber blends are noticeably heavier than the base plastic, and moisture adds weight without adding print quality, so a damp spool weighs more than a dry one. When accuracy matters, use the density printed on your spool's data sheet, and use the grams figure from your slicer, which already uses the density in the filament profile.
Diameter matters for length, not for weight. A 1 kg spool of 1.75 mm PLA holds about 335 m of filament. The same kilogram in 2.85 mm holds about 126 m, because the thicker strand packs more plastic per meter: 7.91 g per meter against 2.98 g. The calculator handles both diameters, and the grams figure is the same either way for the same print.
How much electricity does a 3D printer use?
Most desktop FDM printers average 50 to 250 watts while printing, and the exact number depends on the printer, the material, and whether the chamber is heated. The best figures are the maker's own published measurements: Bambu Lab publishes average power while printing for every model on its power parameters page, and the table below uses those figures.
| Printer | Average while printing PLA | High-temperature filament | Cost per hour at $0.18 per kWh |
|---|---|---|---|
| Bambu Lab A1 mini | 80 W | Not published | 1.4 cents |
| Bambu Lab A1 | 95 W | 200 W (ABS) | 1.7 cents |
| Bambu Lab P1S | 105 W | 140 W (ABS) | 1.9 cents |
| Bambu Lab P2S | 200 W | Not published | 3.6 cents |
| Bambu Lab X2D | 250 W | 550 W (PC) | 4.5 cents |
Other makers' printers of the same type draw similar amounts. SpoolMath's class table, built from its printer database, puts open-frame budget machines (Ender 3 V3 SE, Prusa MINI+) at 60 to 100 W, open-frame fast machines (Bambu A1, A1 Mini, Prusa MK4S) at 90 to 130 W, enclosed CoreXY machines on PLA (Bambu P1S, Prusa CORE One) at 130 to 180 W, enclosed CoreXY machines on ABS or ASA (Bambu X1C, Creality K1 Max) at 200 to 280 W, and large-format machines (Prusa XL, Anycubic Kobra 3 Max) at 180 to 250 W. PrintablePress puts entry-level machines in the Ender 3 class at 70 to 120 W and mid-range enclosed printers at 150 to 250 W. The pattern is consistent: open-frame PLA printers sit near 100 W, enclosed printers sit higher, and high-temperature materials roughly double the draw on the same printer, because the bed and the chamber run hotter.
Peak watts are not average watts, and the spec sheet quotes the peak. A P1S is rated at 1,000 W at 220 V and 350 W at 110 V, and an A1 at 1,300 W at 220 V and 350 W at 110 V. Those are the brief spikes when the heated bed and hot end warm up together at the start of a print, lasting 3 to 5 minutes. For a typical 4-hour print the peak covers about 2 percent of the runtime; the other 98 percent runs at roughly a third of the peak. The heated bed is the biggest load: 100 to 200 W during warm-up, 30 to 80 W while maintaining temperature. The hot end runs 30 to 50 W, and motors and electronics add under 20 W together. Using the spec-sheet peak in the calculator overstates the electricity cost by a factor of two or more, which is why the presets use measured averages and the form asks for average watts.
Published averages disagree, and the disagreement is worth knowing. Bambu Lab measures the P1S at 105 W on PLA; SpoolMath's database uses 150 W for the same printer. Bambu measures the A1 mini at 80 W; SpoolMath uses 90 W. Bambu measures the A1 at 95 W; SpoolMath's worked example uses 110 W. The gap comes from different test conditions: material, bed temperature, room temperature, print speed, and whether the measurement covers heat-up. The calculator's presets use Bambu Lab's published figures, because they are the maker's own measurements for each model, and the form lets you type your own number. The only way to know your own printer's draw is to measure it: a smart plug with energy monitoring, or a plug-in power meter, costs $10 to $15 and reads the total kWh for a full print. Measure one typical print and type that average in.
A month of hobby printing costs a dollar or two in power. At $0.18 per kWh, an A1 mini printing 4 hours a day uses 9.6 kWh a month in printing power, about $1.73. An A1 at the same use prints on 11.4 kWh, about $2.05, and about $2.50 counting standby. A P2S at the same use costs about $5.20 a month including standby. SpoolMath puts a typical hobbyist printing 10 to 15 hours a week at $1 to $4 a month, and notes that the filament costs 5 to 20 times more per print than the electricity. Standby is the quiet extra: most Bambu A-series and P-series printers draw 4 to 8 W idle, and the H2 series draws 25 to 29 W, which left on all month uses about 19 kWh, roughly $3.40. Turn the printer off between sessions, especially an H2-series machine. Our Phone Charging Time Calculator uses the same watts-times-hours math for a much smaller device, if you want to see how the formula behaves at the other end of the scale.
How to price 3D prints to sell
Start from the full cost, add your time and your fees, then set the price from a margin target, not from a multiple of the filament. The filament is usually the smallest number on the bill, so any rule based on filament alone undercharges.
Markup and margin are different math, and mixing them up is the most common pricing error. Markup is the percentage added to cost: price equals cost times 1 plus the markup. Margin is the share of the selling price that is profit: price equals cost divided by 1 minus the margin. The table below shows the equivalents for a print that costs $10.00 to make.
| Margin (share of price) | Equivalent markup (on cost) | Price if cost is $10.00 |
|---|---|---|
| 30 percent | 42.9 percent | $14.29 |
| 40 percent | 66.7 percent | $16.67 |
| 50 percent | 100 percent | $20.00 |
| 60 percent | 150 percent | $25.00 |
A 2x markup is a 50 percent margin. Dividing by 0.6 is a 1.67x markup, a 40 percent margin, which GrandpaCAD calls a frequently cited target. Price Profit Tools suggests choosing a profit margin of 30 to 50 percent of the selling price. Common markups run from about 1.2x, a 20 percent bump, up to 2x, doubling. The calculator takes a markup and shows the implied margin beside the price, so you can see both numbers at once. Pick one convention and stay consistent: quoting a "50 percent margin" when you meant a 50 percent markup gives away a sixth of the price.
What sellers actually charge, per gram and per hour, varies enormously by print size. PrintCost.site priced 9 real prints with its formula and found shop prices from $0.04 per gram for a life-size figure to $0.91 per gram for a keychain, and from $1.21 an hour for a cosplay helmet to $9.80 an hour for a keychain. Three of the nine sat on the $5.00 minimum charge. That spread is the reason a flat per-gram rate fails: at $0.91 a gram the life-size figure would cost about $15,236 instead of $685, and at $0.04 a gram the keychain would cost about $0.22 instead of $5.00. NestOfTools gives the hobby rule as two to three times the total cost, with a minimum order price such as $10 so tiny prints are not sold at a loss after fees and packaging. Orixiva puts the common rule at doubling the full cost, a 100 percent markup, then adjusting for design time and demand. TopSTL agrees: many sellers use a markup of 100 percent or more on top of their costs, because the material is cheap but the work is not.
Marketplace fees come out of the margin, so gross the price up for them. For US sellers on Etsy in 2026 the main fees are a $0.20 listing fee per item, a 6.5 percent transaction fee on the item price plus shipping, and payment processing of 3 percent plus $0.25, which works out to roughly 9.5 percent plus $0.45 on a typical sale before ads. Orders from Etsy Offsite Ads add 12 to 15 percent more. Price Profit Tools shows the effect plainly: a print costing $17.41 with a 35 percent margin target needs a price of $33.21 once 9.5 percent fees are grossed up, and pricing it at $26.79 without the gross-up cuts the real margin to about 22 percent. GrandpaCAD puts the platform cut at roughly 5 to 15 percent of the sale plus a fixed fee around $0.25 to $0.50 per order across Etsy, PayPal, Stripe, and friends. Bake the fees in before you set the sticker price, not after, or the platform eats your margin. The calculator's selling price is before fees: add them on top.
Set a minimum charge, and charge for your time. Small prints cost the most per gram because the fixed work, slicing, setup, support removal, packing, is the same whatever the size. PrintCost.site uses a $5.00 minimum charge; NestOfTools suggests $10. Without a minimum, a 5.5 g keychain prices at a few cents of filament and loses money on every order. For labor, community-reported figures for setup and slicing work run about $25 to $50 an hour, and 15 minutes of hands-on work at $20 an hour is $5.00, which on a small print is often more than the material, electricity, and wear combined. A rate of zero means you are working for free. If you sell the same design repeatedly, weigh one finished run and use that measured weight for every copy, and check your profit per print hour on long prints: a print can look profitable on margin and earn very little per hour of machine time.
How to cut the cost of a print
Lower the infill where strength does not matter. Decorative figures and busts rarely need more than 10 to 15 percent infill. Cutting infill from 20 percent to 10 percent on a large model often saves more money than anything else, because the interior is the bulk of the volume. Small models are the exception: walls and top and bottom layers are printed solid whatever the infill, and on a 20 mm ball the solid skin is 32 to 49 percent of the volume even at 0 percent infill, so lowering infill barely moves the weight.
Use fewer supports, and orient the model to need them. Supports are pure waste after removal, and they typically add 10 to 20 percent to the filament weight. Tree supports use 30 to 50 percent less filament than standard linear supports, and rotating a model 45 to 90 degrees can remove supports entirely on many designs. Check the slicer's support estimate before you print, and include it in the grams figure.
Batch small parts on one plate. Setup and removal happen once for the whole plate, so the hands-on time per part drops sharply, and the printer heats up once instead of several times. The warm-up phase uses disproportionately more energy per unit of time than steady printing, so one long session beats several short ones on power too.
Buy filament in bulk, and buy refills for the materials you use most. Bambu Lab's refills cost $3 less per kg than the same filament on a spool, if you already own a reusable spool. Polymaker lists PolyLite PLA at $49.99 for 3 kg and $79.99 for 5 kg, about $16.66 and $16.00 per kg against $19.99 for a single kilogram. Multi-spool packs often bring PLA under $18 per kg. But the cheapest filament is the one that ends up in a good print: a failed print from a bad spool costs more than the few dollars saved on the spool, and inconsistent diameter is a common cause of failures.
Keep filament dry, and calibrate once. Nylon, TPU, and PETG absorb moisture from the air, and wet filament prints with bubbles, stringing, and weak layers, which raises the failure rate. Store open spools sealed with desiccant, and dry them according to the maker's data sheet if prints start to pop or string. A tuned first layer and flow setting prevent the failed prints that burn through spools, and a small test print checks the fit before you commit hundreds of grams.
Print PLA when it does the job. PLA needs the lowest temperatures of any common filament, a 40 to 60 degree bed against 95 to 110 for ABS, so it uses the least power and needs no enclosure. It is also the cheapest material per kilogram. Paying more makes sense for heat resistance, toughness, or flexibility, and not otherwise.
Resin printing is a different cost story
This calculator is FDM-focused: it prices filament, not resin. Resin printing has a different cost shape, and the numbers above do not transfer. Resin itself usually costs $25 to $50 per liter, against about $15 to $25 per kilogram for PLA, and a resin print also needs isopropyl alcohol for washing, gloves, paper towels, and replacement vat film, which FDM printing does not. Resin printers use less electricity, typically 20 to 60 watts during operation, because they have no heated bed or hot nozzle, but a wash-and-cure station adds 20 to 40 watt-hours per batch, and the combined workflow averages 40 to 100 watts. Put together, resin prints usually cost more per part than FDM prints, and resin is still the best choice for very small, highly detailed miniatures, where FDM cannot match the detail. If you print resin, price the bottle by the milliliter, add the consumables, and do not use this calculator's filament math.
Common mistakes to avoid
Pricing on filament alone. The single most common mistake in the hobby. Filament is often the smallest line on the bill once wear, failures, and time are counted: in the worked examples above, a 50 g print costs $1.00 in filament and $2.00 all in, and an 85 g print costs $1.70 in filament and $3.84 all in. Pricing on grams badly undercharges long prints in particular, because wear and power scale with hours, not grams.
Using the peak watts from the spec sheet. A printer rated at 350 W or 1,000 W draws that for 3 to 5 minutes at heat-up and far less for the rest of the print. Using the peak overstates the electricity cost by a factor of two or more. Use the measured average, or the presets in the calculator, which come from Bambu Lab's published measurements.
Forgetting supports, brims, and purge lines. The grams figure must include everything the printer extrudes. Supports add 10 to 20 percent, and multicolor purge can outweigh a small part. A slicer estimate that reports only the model weight understates the cost by 10 to 40 percent depending on the geometry.
Ignoring failed prints entirely. A batch looks profitable on paper while the scrap bin tells a different story. At a 10 percent failure rate each good print carries 11.1 percent more cost. Track your real failure rate over a month or two and use that number.
Using the gross spool weight. A "1 kg" spool holds 1,000 g of filament, and the spool itself weighs 130 to 250 g extra. Dividing the spool price by the gross weight understates the price per gram and makes every print look cheaper than it is. Use the net filament weight printed on the spool.
Using the cheapest price instead of the price you paid. The price that matters for your cost is the one on your receipt, including shipping, not the lowest price on the market. A specialty color or brand can cost double the budget option, and pricing a carbon-fiber part at a PLA price loses money or forces a renegotiation.
Confusing markup and margin. A 50 percent markup is a 33.3 percent margin, not 50 percent. A 2x markup is a 50 percent margin. Quoting one when you mean the other gives away a sixth of the price or overcharges by the same amount. The calculator shows both, so check the margin line before you list.
Charging one flat rate per gram. Real shop prices run from $0.04 per gram for a life-size figure to $0.91 per gram for a keychain, because the fixed work is the same whatever the size. One rate cannot fit both. Price each job from its own weight and time, and set a minimum charge so small prints are worth taking.
Frequently asked questions
How much does it cost to 3D print something?
For a typical small print, about $2.00 all in. A 50 g PLA print at $20 per kg, 3 hours on a 100 W printer at $0.18 per kWh, with wear at $0.25 an hour and a 10 percent failure rate, costs $1.00 in filament, $0.05 in electricity, and $0.75 in wear, $1.80 before failures and $2.00 once failed prints are counted. Larger prints cost more in proportion: an 85 g print over 6.5 hours costs about $3.84, and a 300 g print over 15 hours costs about $11.13, with wear and failures included. Your own numbers will differ with the material, the print time, and your electricity rate, so enter them above.
How much does 1 gram of PLA filament cost?
About 2 cents. Divide the spool price by the spool weight in grams: a $20 spool of 1,000 g costs $0.02 per gram, and at the makers' September 2026 list prices of $18.99 to $19.99 per kg it is 1.9 to 2.0 cents per gram. PETG costs about 1.7 to 2.5 cents per gram at $16.99 to $24.99 per kg, TPU about 3.9 to 5.0 cents, and nylon about 6.7 to 8.0 cents. Premium or specialty filaments cost more per gram, so always price the material you actually used.
How much electricity does a 3D printer use?
About 80 to 250 watts on average while printing PLA, depending on the printer. Bambu Lab measures the A1 mini at 80 W, the A1 at 95 W, the P1S at 105 W, the P2S at 200 W, and the X2D at 250 W. At $0.18 per kWh, a 10-hour print at 100 W uses 1 kWh and costs 18 cents. High-temperature filaments draw more: the A1 averages 200 W on ABS and the X2D 550 W on polycarbonate. The peak on the spec sheet is much higher, up to 1,000 W or more, but it lasts only 3 to 5 minutes at heat-up.
How many meters of filament are on a 1 kg spool?
For 1.75 mm filament, about 335 m of PLA, 327 m of PETG, 400 m of ABS, 344 m of TPU, and 365 m of nylon, because lighter plastics give more length per kilogram. For 2.85 mm filament it is about 2.65 times less: roughly 126 m of PLA per kg. One meter of 1.75 mm PLA weighs 2.98 g, and one meter of 1.75 mm ABS weighs 2.50 g. The exact length depends on the density of your spool, so check its data sheet for filled filaments.
How should I price 3D prints to sell?
Work out the full cost first, including filament, electricity, wear, and failed prints, then add your hands-on time and a markup. A 50 percent markup on a $2.00 cost gives a $3.01 selling price, a 33.3 percent margin. Many sellers charge at least double their cost, a 100 percent markup, and add more for design work. Remember that markup and margin are different: a 2x markup is a 50 percent margin. Marketplace fees come out of the margin, so gross the price up for them: Etsy takes roughly 9.5 percent plus $0.45 on a typical US sale. Set a minimum charge, $5 to $10, so small prints are worth taking.
What failure rate should I use?
Start at 10 percent, then replace it with your own measured rate. Ten percent is the starting point most pricing guides use. A well-tuned machine you babysit runs near 5 percent, and a busy shop on long unattended jobs runs nearer 15 percent. Count your total prints and failed prints over a month or two to find your real rate. This calculator divides by 1 minus the failure rate, so a 10 percent rate adds about 11.1 percent to the cost of each good print, because one print in ten never ships. Some guides add the rate instead, which gives a slightly lower number.
Is resin printing cheaper than FDM printing?
Usually not, per part. Resin typically costs $25 to $50 per liter, against about $15 to $25 per kilogram for PLA, and a resin print also needs isopropyl alcohol, gloves, and replacement vat film. Resin printers use less electricity, 20 to 60 watts against 50 to 250 watts for FDM, but the material and consumables usually make resin prints cost more. Resin is still the best choice for very small, highly detailed miniatures. This calculator is FDM-focused and does not price resin prints.
Sources
Every figure on this page comes from one of the sources below, each accessed 20 November 2026. Where sources disagree, the page shows the disagreement and says which figure the calculator uses.
- eia.gov — EIA Electric Power Monthly, Table 5.6.A: average residential electricity price, August 2026, US total 18.16 cents per kWh (17.57 a year earlier); Hawaii 47.18, California 29.75, New York 28.65, Texas 15.91, Florida 14.99, North Dakota 13.31. Accessed 20 November 2026.
- bitfab.io — Densities of all 3D printing materials: PLA 1.24, ABS 1.04, PETG 1.27, nylon 1.52, flexible (TPU) 1.21 g per cubic cm; meters per kg at 1.75 mm (PLA 335, ABS 400, PETG 328, nylon 274, TPU 344); grams per meter at 1.75 mm (PLA 2.98, ABS 2.50, PETG 3.05, TPU 2.91). Accessed 20 November 2026.
- mogerio.com — Filament length to weight calculator: PLA 1.24, PETG 1.27, ABS 1.04, TPU 1.21, nylon 1.14 g per cubic cm; one meter of 1.75 mm filament is 2.405 cubic cm, weighing 2.98 g in PLA and 2.50 g in ABS; about 335 m of PLA, 325 m of PETG, and 400 m of ABS per kg. Accessed 20 November 2026.
- stltomp4.com — Estimate 3D print weight and filament cost: PLA 1.24, PETG 1.27, ABS 1.04, TPU 1.21, nylon (PA) 1.01 to 1.14 g per cubic cm (PA12 low, PA6 high); shell share of a 20 mm ball 32 to 49 percent even at 0 percent infill. Accessed 20 November 2026.
- 3dprinterguide.co.uk — Filament types explained: Polymaker technical data table lists PolyLite PLA at 1.17, PolyLite PETG at 1.25, PolyLite ABS at 1.04, PolyFlex TPU95 at 1.22, and PolyMide CoPA nylon at 1.12 g per cubic cm; Prusa temperatures (PLA nozzle 210 plus or minus 10 degrees, bed 40 to 60; PETG 250 plus or minus 10, bed 80 plus or minus 10; TPU 95A 230 plus or minus 10, bed 65 plus or minus 10; PA11 275 plus or minus 10, bed 100 plus or minus 10). Accessed 20 November 2026.
- firstlayerlab.com — 3D printer filament cost: list prices read 29 September 2026 from the makers' own US stores, 1 kg of 1.75 mm filament with a spool (PLA $18.99 to $19.99, PETG $16.99 to $24.99, ABS $18.99 to $19.99, TPU $38.99 to $49.99, nylon $66.65 to $79.99); Bambu Lab data sheet densities PLA 1.24, PETG 1.25, ASA 1.05; refills $3 less per kg; Polymaker 3 kg $49.99 and 5 kg $79.99. Accessed 20 November 2026.
- productbible.com — How much electricity does a 3D printer use: Bambu Lab published average power while printing PLA (A1 mini 80 W, A1 95 W, P1S 105 W, P2S 200 W, X2D 250 W; A1 200 W on ABS, P1S 140 W on ABS, X2D 550 W on PC); standby 4 to 8 W (A and P series), 25 to 29 W (H2 series); A1 maximum draw 350 W at 110 V. Accessed 20 November 2026.
- spoolmath.com — Do 3D printers use a lot of electricity: most consumer FDM printers use 60 to 200 W; class table (open-frame budget 60 to 100 W, open-frame fast 90 to 130 W, enclosed CoreXY on PLA 130 to 180 W, enclosed CoreXY on ABS 200 to 280 W, large-format 180 to 250 W); per-printer averages (MK4S 80 W, A1 Mini 90 W, P1S 150 W, Prusa XL 180 W, K1 Max 200 W); peak lasts 3 to 5 minutes, about 2 percent of a 4-hour print; hobbyist $1 to $4 a month. Accessed 20 November 2026.
- printablepress.com — How much electricity does a 3D printer use: desktop FDM printers draw 50 to 250 W on average; Ender 3 class 70 to 120 W, mid-range enclosed 150 to 250 W, high-temperature engineering 400 to 600 W, consumer resin 20 to 60 W, resin plus wash and cure 40 to 100 W combined; heated bed 100 to 200 W warming up, 30 to 80 W maintaining; hot end 30 to 40 W. Accessed 20 November 2026.
- printcost.site — How to price 3D prints: price equals (filament plus electricity plus wear plus labor plus packaging) times (1 plus failure buffer) times (1 plus markup); defaults PLA $20 per kg, 120 W at $0.17 per kWh, wear $0.25 an hour, labor $2.00 per job, failure buffer 10 percent, markup 50 percent, minimum charge $5.00; 9 real prints priced from $0.04 to $0.91 per gram and $1.21 to $9.80 an hour. Accessed 20 November 2026.
- calcgoose.com — 3D print cost calculator: failure adjustment divides by (1 minus failure rate), so a 10 percent rate raises cost by 11.1 percent; printer lifetime 3,000 to 5,000 hours for a consumer FDM machine; a $400 printer over 4,000 hours costs $0.10 an hour; typical FDM printer averages 100 to 180 W; Etsy takes roughly 9.5 percent plus payment processing. Accessed 20 November 2026.
- priceprofittools.com — How to price 3D prints: worked example of a 45 g phone stand (material $0.96, electricity $0.04, machine cost $0.53, failure allowance $0.08, labor $8.33, packaging $0.80, overhead $1.07, total $11.81, selling price $19.69 at a 40 percent margin); failure allowance equals cost times f divided by (1 minus f); machine cost $0.30 an hour ($600 printer over 4,000 hours plus $0.15 an hour maintenance); margin and markup table; Etsy fees about 9.5 percent plus $0.45; labor rates $25 to $50 an hour. Accessed 20 November 2026.
- grandpacad.com — How to price 3D prints: desktop FDM printer draws about 50 to 150 W, Prusa published figures near 80 W for PLA and 120 W for ABS; lifetime 3,000 to 10,000 hours, 5,000 the common middle figure; $800 printer over 5,000 hours is $0.16 an hour; failure buffer 5 to 15 percent; markups 1.2x to 2x; 40 percent margin target; platform cut roughly 5 to 15 percent plus $0.25 to $0.50 per order; worked example of a 50 g part (material $1.25, electricity $0.08, depreciation $0.80, failure $0.21, labor $5.00, total $7.34, price $14.68 at 2x). Accessed 20 November 2026.
- nestoftools.com — How to calculate filament cost for a 3D print: PLA $25 per kg ($0.025 per gram), PETG $28, ABS $26, TPU $35; wood and marble blends $40 to $50, carbon fiber $50 to $70, nylon and polycarbonate $60 and up; supports add about 30 percent on a heavy model; machine time commonly $1 to $3 an hour; hobby rule two to three times total cost, minimum order about $10; gross spool weight and model-only weight are the common errors. Accessed 20 November 2026.
- orixiva.com — 3D printing cost calculator: 85 g PLA worked example ($1.79 filament, $0.13 electricity, $0.78 wear, $0.33 maintenance, $3.75 labor, $0.66 extras and failures, $7.43 total); FDM printers average about 100 to 150 W, resin printers 30 to 60 W; common rule at least double the full cost; Etsy fees 2026 ($0.20 listing, 6.5 percent transaction, 3 percent plus $0.25 processing, Offsite Ads 15 percent or 12 percent); resin $25 to $50 per liter. Accessed 20 November 2026.
- topstl.com — How much does it cost to 3D print: PLA $18 to $24 per kg, PETG $20 to $26, ABS $17 to $23, TPU $35 to $50; typical FDM printer draws 80 to 150 W on average; failure rate 5 to 15 percent; worked examples (50 g PLA figure about $1.17, 300 g bust about $7.06); sellers often use a markup of 100 percent or more. Accessed 20 November 2026.
- craftcalculators.com — 3D printing filament cost calculator for makers: machine time about $0.25 to $0.50 per print hour; $600 printer plus $200 in parts over 2,500 hours is about $0.32 an hour; waste allowance 5 to 10 percent; worked examples (42 g phone stand $5.72 to make, about $9 to sell; 180 g planter $14.75 to make, about $22 to sell); Etsy fees take about 12 percent of a $22 sale. Accessed 20 November 2026.
- printingxyz.com — PLA vs PETG vs ABS: a 1 kg spool of PLA, PETG, or ABS costs $18 to $35 in 2026; PLA typically $18 to $25 per kg. Accessed 20 November 2026.