Skip to content

Crop Yield Estimator

Corn field counts

One count per site, separated by commas, 1 to 20 sites. Each count is the ears in 17 feet 5 inches of row at 30-inch spacing. Count only ears the combine header will retrieve.

Average complete rows on every fifth ear, 1 to 30. Most ears run 14 to 18 rows.

Average kernels per row on the same ears, 1 to 60. Skip the butt and tip kernels smaller than half a normal kernel.

Thousands of kernels per 56-lb bushel, a whole number from 60 to 120. Purdue suggests 65, 75, and 85, and 90 to 100 after stressful grain fill.

Field size and moisture (optional)

Leave blank to skip the field total. Enter the acres to get total bushels for the field.

A weighed or scaled yield to standardize to market moisture. Leave both moisture fields blank to skip.

Moisture of the measured yield, 5 to 50%. Market standards: corn 15.5%, soybeans 13%, wheat 13.5%.

Your crop yield estimate

How the numbers were worked out

      This tool estimates crop yield from the field counts you enter, for general planning only. It is not a measured yield and not a guarantee of what the field will produce. Kernel weight, seed size, and late-season weather move the real result, so count again closer to harvest and check the estimate against your scale tickets before booking sales or storage on it.
      Pre-harvest yield in bushels per acre, from field counts: corn by the Purdue kernel-count method or the Ohio State ear-weight method, soybeans by the Purdue pod-count method, wheat by the Nebraska head-count method. With the defaults, corn averages 204.8 bushels per acre at a kernel factor of 75 (180.7 to 236.3 across kernel sizes), soybeans 55.6 bushels per acre, and wheat 42.2 bushels per acre. Enter your counts at five or more sites for your field average, planning band, and field total.

      Last reviewed: 21 November 2026. Reviewed annually; next review due 19 May 2027.

      How to use the Crop Yield Estimator

      Corn growers estimate yield in August to book sales, size storage, and settle landlord-share questions. Most online tools cover corn only, and they cover it one way. This estimator covers corn, soybeans, and wheat in one place, with the extension method for each crop: the Purdue kernel-count method and the Ohio State ear-weight method for corn, Purdue's simplified pod-count method for soybeans, and the Nebraska head-count method for wheat. Every method runs on counts you take in the field, and every result prints the full working, so the answer can be checked with a pocket calculator.

      All four methods share one idea. Count how many kernels the crop has set on a known area, then divide by how many kernels make a bushel. The bushel is a weight in grain trade, not a volume: 56 pounds for shelled corn, 60 pounds for soybeans and for wheat. The kernel weight is the one part you cannot measure before harvest, so each method carries a published factor that stands in for it. That factor is the main source of error in every estimate on this page, which is why the corn result shows the range across kernel sizes instead of a single number.

      To get your result, follow these steps:

      1. Pick a crop. Choose corn, soybeans, or wheat. The form shows only the fields that crop needs, and the result changes to match: corn results lead with the kernel-factor range, soybean results with the seed-size factor, wheat results with heads per square foot.
      2. For corn, pick a method. Kernel count works from the milk stage (R3) onward, as early as 18 to 22 days after pollination is complete. Ear weight works only after black layer, when the grain is about 30 to 35% moisture, because it weighs real ears. Ear weight is the more accurate of the two, but it needs a scale and a moisture tester.
      3. Enter the site counts. One count per sample site, separated by commas, up to 20 sites. For corn, each count is the harvestable ears in 1/1000 acre of row: 17 feet 5 inches of row at 30-inch spacing. For soybeans, each count is the pods in 1/10,000 acre: 21 inches of row, one row at 30-inch spacing, two rows at 15-inch, four rows at 7.5-inch. For wheat, each count is the heads per foot of row: count the harvestable heads in 5 feet of row and divide by 5. Sample at least 5 spots spread across the field, away from end rows, wheel tracks, and field edges.
      4. Enter the second counts. For corn kernel count, that is kernel rows per ear and kernels per row, averaged over every fifth ear in the sample row. For corn ear weight, it is the average ear weight and the grain moisture. For soybeans, seeds per pod and seeds per pound. For wheat, kernels per head and row spacing. The hints under each field give the usual ranges and the extension defaults.
      5. Optionally, enter the field size and a measured yield. The field size turns bushels per acre into total bushels for the field. The measured yield and its moisture standardize a weighed or scaled yield to market moisture: corn 15.5%, soybeans 13%, wheat 13.5%. Leave both moisture fields blank to skip that part.
      6. Read the full result. The headline leads with the field average in bushels per acre. The cards show the range, the planning band, pounds per acre, kilograms per hectare, and the lowest and highest sites. The guidance explains the result in plain language, the warnings flag the assumptions that need a second look, and the steps print the full working.

      The tool updates as you type, so you can try different counts quickly. Try the example buttons under the form. Each one loads a worked example from the extension publication behind the method: Purdue's corn example, Ohio State's ear-weight example, Purdue's soybean example, and Nebraska's wheat example. The worked examples section below shows every number in them.

      How it works

      The calculator runs a different published formula for each crop, then averages the site yields the way the publications tell you to: each site is calculated separately, and the field average is the mean of the site yields. It never averages the counts first and calculates once, because that hides how much the field varies. The spread between the lowest and highest site is part of the answer.

      Corn: the kernel-count method

      The yield component method was originally described by the University of Illinois and is published in full by Purdue Extension agronomist R.L. Nielsen. It uses four components: ears per acre, kernel rows per ear, kernels per row, and weight per kernel. The first three are counted in the field. Kernel weight cannot be measured until the grain matures, so the formula uses a kernel factor: thousands of kernels per 56-pound bushel. Purdue suggests running the numbers with factors of 65, 75, and 85, which cover the range most common in the central Corn Belt, and 90 to 100 when grain fill was stressful. In Purdue's own trials, kernel numbers ran from 67,000 to 94,000 per bushel, averaging about 76,000. The original factor, from the days of smaller kernels, was 90.

      The formula is: bushels per acre equals ears in 1/1000 acre times kernels per ear, divided by the kernel factor. Kernels per ear is kernel rows times kernels per row, averaged over the sampled ears. The 1/1000-acre row length is 17.4 feet at 30-inch spacing; for other spacings, divide 43,560 by the row spacing in feet, then divide by 1,000. Count only harvestable ears: not dropped ears, and not ears on severely lodged plants unless the combine header will retrieve them. Do not sample nubbins or obviously odd ears unless they fairly represent the sample area, and do not count aborted kernels or the extreme butt and tip kernels.

      Corn: the ear-weight method

      Ohio State Extension publishes the ear-weight method alongside the kernel-count method. It weighs ears instead of counting kernels, so it needs the grain to be physiologically mature: black layer, at about 30 to 35% grain moisture. At each site, count the harvestable ears in 1/1000 acre, weigh every fifth ear, hand-shell the same ears, and test the grain moisture. The formula is: bushels per acre equals ears times average ear weight in pounds, divided by 1.411 times the moisture percentage plus 46.2, times 1,000. The denominator already standardizes the result to 15.5% moisture, the market standard for corn, so the answer must not be corrected for moisture a second time. The method still carries a fudge factor for the average shellout percentage, so it is an estimate, not a scale weight, but because it weighs real ears it should be somewhat more accurate than the kernel-count method.

      Soybeans: the pod-count method

      Purdue Extension agronomist Shaun Casteel simplified the soybean yield estimate to three counts. The formula is: bushels per acre equals pods in 1/10,000 acre times seeds per pod, divided by a seed-size factor. The factor is 18 for 3,000 seeds per pound, 15 for 2,500 seeds (larger seeds), and 21 for 3,500 seeds (smaller seeds after late-season stress). The starting point for seeds per pod is 2.5, since pods carry 1, 2, 3, or 4 seeds. Count the pods in 21 inches of row: one row at 30-inch spacing, two rows at 15-inch, four rows at 7.5-inch. Count pods that are R5 or larger, with the knowledge that some of the smaller pods may or may not make it. The result is standardized to 13% moisture.

      The full equation behind the shortcut is the University of Nebraska's: bushels per acre equals plants per acre times pods per plant times seeds per pod, divided by seeds per pound times 60 pounds per bushel. The 60-pound soybean bushel is the volume-weight standard the USDA set in 1925. Purdue's shortcut counts pods directly instead of plants times pods per plant, which is what makes it fast enough to run at many spots in a field. The seeds-per-pound figure is printed on the tag of a bag of varietal seed, and that tag is the best guide to the factor for your variety, adjusted up or down for how the season treated seed size.

      Wheat: the head-count method

      Nebraska Extension's NebGuide G1429 gives the head-count formula for winter wheat: bushels per acre equals heads per foot of row times kernels per head, divided by row spacing in inches, times 0.48. The 0.48 factor carries the kernel weight: it assumes about 22 kernels per head and 16,000 kernels per pound. Count the heads in 5 feet of row at five or more sites, count kernels on at least 5 heads at each site, and measure the row spacing. The guide notes that many hail adjusters in Nebraska use this method. Kansas Wheat's wheat tour uses the USDA/NASS late-season formula, which counts spikelets per head and kernels per spikelet instead of kernels per head directly; the two agree when the kernel counts agree. Spikelets usually run 6 to 12 per head, kernels per spikelet 2 to 3, and the Wheat Quality Council uses 2.3 kernels per spikelet as the default, 2.1 under stress.

      Worked examples

      Each example below is the publication's own worked example, run through the calculator's formulas. The numbers are the ones the publications print, so they double as a check on the tool.

      Crop and methodCountsWorkingResult
      Corn, kernel count (Purdue)30 ears, 511 kernels per ear30 x 511 / 65, 75, 85236, 204, 180 bu per acre
      Corn, kernel count (Ohio State)29 ears, 16 rows, 33 kernels per row29 x 16 x 33 / 85180 bu per acre
      Corn, ear weight (Ohio State)24 ears, 0.5 lb, 30% moisture(24 x 0.5) / (1.411 x 30 + 46.2) x 1,000135 bu per acre
      Soybeans, pod count (Purdue)400 pods, 2.5 seeds per pod, factor 18400 x 2.5 / 1855.6 bu per acre
      Wheat, head count (Nebraska)30 heads per foot, 22 kernels, 12-inch rows30 x 22 / 12 x 0.4826.4 bu per acre

      Two of the printed figures need a note. Purdue's soybean article prints 55.5 bushels for the 400-pod example; the arithmetic gives 55.56, which rounds to 55.6, and the calculator uses 55.6. Ohio State prints 180 bushels for its kernel-count example; the arithmetic gives 180.1, and the calculator keeps the decimal. The differences are rounding, not method.

      Moisture standardization

      Grain is bought and sold at market moisture, so a yield measured at any other moisture has to be standardized before it means anything. The standards are corn 15.5%, soybeans 13%, and wheat 13.5%, at 56, 60, and 60 pounds per bushel. The math is dry matter: standardized bushels equal measured bushels times 100 minus the measured moisture, divided by 100 minus the market moisture. A load of corn weighed at 22% moisture standardizes to fewer bushels at 15.5%, because part of the weighed weight was water. The University of Wisconsin's hand-harvest method works the same way in pounds: 10 pounds of grain from 1/1000 acre at 22% moisture is 7.8 pounds of dry matter per thousandth, 7,800 pounds per acre, 9,231 pounds at 15.5% moisture, and 165 bushels per acre. The ear-weight method needs no separate standardization, because its denominator already does it.

      The multi-site field average

      No field is uniform, and a single sample spot can be 20 bushels away from the field average in either direction. Every publication behind this tool says the same thing: sample several spots and average the results. Iowa State recommends at least 5 places in a field and at least 10 ears at each, and more estimates if the field is highly variable. Ohio State says to repeat the procedure for at least four additional sites. Nebraska's wheat guide asks for at least 5 feet of row at five or more sites. The calculator follows that advice literally: it calculates each site separately, averages the site yields, and reports the lowest site, the highest site, and the spread. When the spread is more than 30% of the average, the result carries a warning, because the average of a field that varies that much is not a number to book sales on without more sampling.

      How accurate is the estimate

      Purdue puts the corn kernel-count method within about plus or minus 20 bushels of the actual yield, and Iowa State and Ohio State say the same for both corn methods. That band is wide, and it is honest: kernel weight is not final until black layer, and a stressful grain fill can move the kernel factor by 20,000 kernels per bushel for the same hybrid from one year to the next. In a year with poor grain fill the method overestimates, because the kernels weigh less than the factor assumes; in a year with excellent grain fill it underestimates. The closer to black layer you sample, the better you can judge whether kernel weight will be above or below average this year, and the tighter the estimate gets.

      Soybean estimates are tighter in practice: experienced estimators expect to land within about 5 bushels of the actual yield, though the estimate can be 10 off. The weak point is seed size, which is not final until the pods fill, and late-season weather moves it. Wheat estimates carry the same kernel-weight uncertainty, plus the 0.48 factor's assumption of 22 kernels per head: a crop that set fewer kernels per head than average will come in below the estimate, and the only fix is to count kernels on real heads instead of using the default. For all three crops, the estimate is a planning figure. Use it to book sales, size storage, and settle landlord-share questions. Do not treat it as a guarantee, and count again closer to harvest: the last count before the combine is the one that pays.

      What to do with the answer

      A yield estimate earns its keep in the weeks before harvest, when the decisions are still open. The first is sales: an August estimate lets a grower forward-contract part of the crop with a number behind it instead of a guess. The second is storage: total bushels for the field, which the calculator prints when the field size is entered, says whether the bins hold the crop or whether some of it has to move at harvest. The third is the landlord share, where a pre-harvest estimate settles the split before the scale tickets arrive. The fourth, for corn, is the grain-or-silage decision: the kernel-count method works early enough to help decide whether a stressed field pays better as grain or as silage, and Ohio State notes exactly that advantage.

      The estimate also feeds the rest of the harvest plan. Wet corn has to be dried, and the drying bill depends on the bushels and the moisture: our Grain Drying Cost Calculator works out drying cost, moisture shrink, and the deliver-wet comparison from wet bushels. A field taken for silage instead of grain needs storage sized to the tonnage: our Silage Storage Calculator turns bunker, pile, bag, and tower dimensions into tons and feed days. The harvest itself has a cost per acre that the yield decides the value of: our Farm Machinery Cost Calculator prices tractors and implements by the hour and the acre. Looking ahead to next season, our Seed Rate Calculator sets the seeding rate from the target stand, and our Soil Test Interpreter turns a soil test into fertilizer advice. The nutrients the crop removes go back on as manure or fertilizer: our Manure Fertilizer Value Calculator prices manure by its nutrient content, and a livestock enterprise on the same farm can balance its rations with our Livestock Ration Balancer.

      Sources

      Frequently asked questions

      How do you estimate corn yield before harvest?

      Count harvestable ears in 1/1000 acre of row, which is 17 feet 5 inches at 30-inch spacing, then count kernel rows and kernels per row on every fifth ear. Multiply ears by average kernels per ear and divide by a kernel factor: 65, 75, or 85. Purdue's example is 30 ears with 511 kernels per ear, which gives 236, 204, and 180 bushels per acre at the three factors. Repeat at five or more sites across the field and average the results. The method works from the milk stage onward, and Purdue puts it within about 20 bushels of the actual yield.

      What is the kernel factor in the corn yield formula?

      The kernel factor stands in for kernel weight, which cannot be measured until the grain matures. It is the number of kernels in a 56-pound bushel, in thousands: a factor of 75 means 75,000 kernels per bushel. Purdue suggests running 65, 75, and 85, which cover the range most common in the central Corn Belt, and 90 to 100 after stressful grain fill, when kernels are small and light. In Purdue's trials, kernel numbers ran from 67,000 to 94,000 per bushel, averaging about 76,000. The original factor, from the days of smaller kernels, was 90.

      How do you estimate soybean yield before harvest?

      Count the pods in 1/10,000 acre, which is 21 inches of row: one row at 30-inch spacing, two rows at 15-inch, four rows at 7.5-inch. Multiply pods by seeds per pod and divide by a seed-size factor: 18 for 3,000 seeds per pound, 15 for 2,500, 21 for 3,500. Purdue's example is 400 pods times 2.5 seeds per pod divided by 18, which is 55.6 bushels per acre. Count pods that are R5 or larger, and use the seed size on the bag tag for the factor. The result is standardized to 13% moisture.

      How do you estimate wheat yield before harvest?

      Count the harvestable heads in 5 feet of row at five or more sites and divide by 5 to get heads per foot, count kernels on at least 5 heads at each site, and measure the row spacing in inches. The Nebraska formula is heads per foot times kernels per head, divided by row spacing, times 0.48. The worked example in NebGuide G1429 is 30 heads per foot with 22 kernels per head in 12-inch rows: 30 times 22 divided by 12 times 0.48 is 26.4 bushels per acre. The 0.48 factor carries the kernel weight, assuming about 22 kernels per head and 16,000 kernels per pound.

      How accurate is a pre-harvest yield estimate?

      For corn, Purdue, Iowa State, and Ohio State all put the estimate within about 20 bushels of the actual yield. Soybean estimates are tighter in practice: experienced estimators expect to land within about 5 bushels, though the estimate can be 10 off. Wheat carries the same kernel-weight uncertainty as corn, plus the 0.48 factor's assumption of 22 kernels per head. The accuracy improves with more sample sites and with later sampling, because kernel weight is not final until the grain matures. A stressful grain fill makes the corn method overestimate, and an excellent grain fill makes it underestimate.

      How many sites should I sample in a field?

      At least five, spread across the field and away from end rows, wheel tracks, field edges, weedy patches, and unusually wet or dry spots. Iowa State recommends at least 5 places in a field and at least 10 ears at each, Ohio State says to repeat the corn procedure for at least four additional sites, and Nebraska's wheat guide asks for at least 5 feet of row at five or more sites. The less uniform the field, the more sites it needs. This calculator warns when fewer than five sites are entered, and warns again when the site yields spread by more than 30% of the average.

      What moisture is a bushel of corn, soybeans, or wheat standardized to?

      Corn is standardized to 15.5% moisture at 56 pounds per bushel, soybeans to 13% at 60 pounds, and wheat to 13.5% at 60 pounds. The standardization is dry-matter math: standardized bushels equal measured bushels times 100 minus the measured moisture, divided by 100 minus the market moisture. Grain weighed wet standardizes to fewer bushels, because part of the weighed weight was water. The ear-weight method needs no separate standardization, because its denominator already standardizes the result to 15.5% moisture.

      When should I use the ear-weight method instead of the kernel-count method?

      Use the ear-weight method after black layer, when the grain is about 30 to 35% moisture, because it weighs real ears and needs the grain to be mature. It is somewhat more accurate than the kernel-count method for that reason, though it still carries a fudge factor for the average shellout percentage. It needs a scale and a moisture tester, and it cannot be used early in the season. The kernel-count method works from the milk stage onward, so it is the right choice for an early estimate, for the grain-or-silage decision, and whenever no scale is handy.