Log Board Foot Calculator
Board feet in this log
How the answer was worked out
Keep scaling: our Timber Value Calculator prices the board feet this log holds, our Tree Height Calculator measures the standing tree before it is cut, and our Tree Planting Calculator plans spacing and hole size for the next tree.
Last reviewed: 21 November 2026. Reviewed every 365 days; next review due 21 November 2027.
How to use the Log Board Foot Calculator
Every woodlot owner, sawyer, and firewood cutter eventually faces the same question: how many board feet are in this log. The answer decides what a log is worth, what a load is worth, and whether a buyer or a seller is getting a fair deal. The trouble is that the question has three answers, not one. The United States has three log rules in common use, Doyle, Scribner, and International 1/4-inch, and each one gives a different number of board feet for the same log. A 12-inch log, 16 feet long, holds 64 board feet by Doyle, 86 by Scribner, and 97 by International. That is a spread of 33 board feet on a single ordinary log, and on a truckload it is the difference between a fair price and a bad one. This calculator gives you all three answers side by side, from two measurements, with the full working printed out so you can check every figure.
A board foot is a piece of lumber 1 inch thick, 12 inches wide, and 12 inches long, which is 144 cubic inches of wood. A log rule estimates how many board feet of lumber a mill will saw out of a round log. It is an estimate, not a measurement of the wood in the log: the rule has to allow for the saw kerf, the wood the blade turns into sawdust, for the slabs cut off the outside to square the log up, and for the taper of the log from one end to the other. Each rule makes different allowances, which is why the three answers differ. The rules also disagree most on small logs, where the fixed deductions bite hardest, and they come together on big logs. Understanding which rule your buyer uses, and how far apart the rules sit on your logs, is worth real money.
To get your result, follow these steps:
- Measure the small-end diameter, inside the bark. Measure across the small end of the log, not the big end, and measure inside the bark: bark is not lumber. Measure in two directions at right angles and average the two numbers, because logs are seldom perfectly round. Enter the diameter in inches. The calculator accepts decimals, so 12.5 inches is fine.
- Measure the length with a tape. Measure the log in feet, without the trim allowance, the extra few inches left on the log so the mill can square the ends. A log just short of a full foot is tallied at the next lower foot length in hardwoods, so a tape beats an eyeball. Enter the length in feet.
- Enter the number of logs, if you have more than one of the same size. Leave the count at 1 for a single log. If you have a pile of identical logs, enter the count and the calculator totals all three rules for the pile.
- Read all three answers, not just one. The headline gives the three board-foot figures side by side, International first, then Scribner, then Doyle. The cards show each rule separately, plus the totals when you entered more than one log, and the gap between Doyle and International as a percent. The guidance explains the gap in plain language and tells you which rule the numbers favor. The warnings flag the cases that need a second look: a log under 6 inches at the small end, a log over 20 feet long, or a log big enough that Doyle scales it higher than International.
- Check the working. The steps print every calculation: the Doyle formula, the Scribner formula, and the International rule worked section by section, with the taper added at each 4-foot section, plus the comparison between Doyle and International. Every printed equation balances on the printed numbers, so you can verify the answer with a pocket calculator.
The tool updates as you type, so you can try different sizes quickly. Try the example buttons under the form. The first is the classic example: a 12-inch log, 16 feet long, which scales 64 board feet by Doyle, 86 by Scribner, and 97 by International. The second is a big sawlog: 16 inches by 16 feet, which scales 144 by Doyle, 166 by Scribner, and 181 by International. The third is a small log, 8 inches by 12 feet, where Doyle bites hardest: 12 board feet by Doyle against 27 by International, less than half. Each example shows a different shape of the answer, and each one prints its working in the steps.
A note on what the calculator does not do: it does not deduct for defects. Rot, sweep, splits, and crook all reduce the lumber a log will saw, and mills scale defective logs back, usually by reducing the length, while many mills refuse badly defective logs outright. The figures here are for a sound, straight log. If your log has visible defects, the mill's scale will come in lower than these numbers, and the gap is a matter for the buyer and the seller to settle, not something a formula can fix.
How it works
All three rules start from the same two measurements: D, the diameter in inches across the small end of the log inside the bark, and L, the length in feet. From those two numbers, each rule computes an estimate of the lumber the log will saw. The formulas below are the published forms: Doyle and the Scribner formula from Purdue Extension publication FNR-191, Log and Tree Scaling Techniques, and the International rule in the section form the USDA Forest Service National Forest Log Scaling Handbook defines.
The Doyle rule: subtract 4, square it, adjust for length
The Doyle rule is the oldest of the three and the simplest to remember. The formula is: board feet equals (D minus 4) squared, times L divided by 16. The 4 inches are a fixed deduction for slabs and edgings, the wood cut off the outside of the log to square it up, and the rule also allows for a saw kerf of 5/16 inch. The formula takes no account of taper: a long log is treated as a cylinder of the small-end diameter, which understates what a tapering log will actually saw.
Worked example: a 12-inch log, 16 feet long. Subtract 4 from 12 to get 8. Square 8 to get 64. Multiply by 16 and divide by 16, which leaves 64. The log scales 64 board feet by Doyle. A second example: a 16-inch log, 16 feet long. Subtract 4 from 16 to get 12, square it to get 144, and the length factor is 1, so the log scales 144 board feet. A third: a 10-inch log, 10 feet long. Subtract 4 from 10 to get 6, square it to get 36, multiply by 10 and divide by 16 to get 22.5, which rounds to 23 board feet. Notice what the fixed 4-inch deduction does to a small log: on a 6-inch log it takes away two thirds of the diameter before the squaring even starts, which is why Doyle scales a 6-inch, 16-foot log at only 4 board feet.
Doyle has a hard edge at the bottom: at a 4-inch diameter the formula gives zero, because 4 minus 4 is zero. Below 4 inches the formula would start giving positive numbers again, which is nonsense, so the calculator takes 4 inches as its minimum diameter. A log under 4 inches at the small end is not a sawlog in any case.
The Scribner rule: a formula for a diagram rule
Scribner is different in kind from the other two. It began as a diagram rule: J. M. Scribner drew the cross-sections of 1-inch boards, in widths of 4, 6, and 8 inches, inside circles representing log ends, leaving 1/4 inch between boards for saw kerf, and counted what fit. The rule is published as tables, not as a formula, and the tables step unevenly: volumes rise only when the diameter grows enough to fit another board or a wider board. The most common form, Scribner Decimal C, rounds the table values to the nearest 10 board feet. Because the diagram rule is awkward to compute, Bruce and Schumacher published a formula in 1950 that smooths out the steps: board feet equals (0.79 times D squared, minus 2 times D, minus 4), times L divided by 16.
Worked example: a 12-inch log, 16 feet long. Multiply 0.79 by 144 to get 113.76, subtract 24 and 4 to get 85.76, and the length factor is 1, so the log scales 85.76 board feet, rounded to 86. A second example: a 16-inch log, 16 feet long. Multiply 0.79 by 256 to get 202.24, subtract 32 and 4 to get 166.24, rounded to 166 board feet. The formula follows the published table within a few board feet, but it is not the table: the Virginia Cooperative Extension comparison table reads 80 board feet for a 12-inch, 16-foot log on the Scribner Decimal C scale, against the formula's 86, and 160 for a 16-inch, 16-foot log, against the formula's 166. When a contract names the Scribner table, use the table; the formula is the right tool for estimating and comparing. Purdue notes that the formula is fairly consistent on logs 16 feet or shorter and under 28 inches in diameter; beyond that range it is an extrapolation of the diagram rule, and the table is the safer reference.
The International 1/4-inch rule: section by section, with taper
The International rule is the most careful of the three, and the only one that allows for taper. The Forest Service handbook defines it as a formula applied to each 4-foot section of the log, with the diameter increasing by 1/2 inch at each section to allow for taper. The basic formula for a 4-foot section is the 1/8-inch kerf form, 0.22 times D squared minus 0.71 times D, multiplied by the 1/4-inch kerf factor 0.904762. A 16-foot log is worked as four sections: the first at the small-end diameter, the second 1/2 inch larger, the third 1 inch larger, and the fourth 1 1/2 inches larger. The section values are added for the total. A log whose length is not a multiple of 4 feet gets a final partial section, prorated by its length: a 10-foot log is two full sections plus a 2-foot section at the next diameter step, worth half a full section.
Worked example: a 12-inch log, 16 feet long. Section 1, at 12 inches: 0.22 times 144 is 31.68, minus 0.71 times 12, which is 8.52, giving 23.16; times 0.904762 gives 20.95 board feet. Section 2, at 12.5 inches: 0.22 times 156.25 is 34.375, minus 8.875, giving 25.5; times 0.904762 gives 23.07. Section 3, at 13 inches: 37.18 minus 9.23 is 27.95; times 0.904762 gives 25.29. Section 4, at 13.5 inches: 40.095 minus 9.585 is 30.51; times 0.904762 gives 27.60. Add the four sections, 20.95 plus 23.07 plus 25.29 plus 27.60, and the log scales 96.91 board feet, rounded to 97. The taper allowance is worth real volume: without it, four sections at 12 inches would give only 83.80 board feet.
The published International tables round to the nearest 5 board feet, so the table reads 95 for this log, against the formula's 97. The calculator shows the unrounded formula value, rounded to the nearest board foot, because that is the number to compare against the other two rules. The Forest Service also publishes an International 1/4-inch Decimal rule, which rounds to the nearest 10 board feet, for use where the Decimal C convention is wanted. Grosenbaugh published an integrated single formula for the International rule in 1952, and the section method used here reproduces it to within two hundredths of a board foot at every standard length, which is a useful check that both forms of the rule agree.
Why the answers differ so much on small logs
The three rules disagree most where the deductions are largest relative to the log. Doyle subtracts a fixed 4 inches whatever the size, so on a 6-inch log it throws away two thirds of the diameter, while on a 40-inch log it throws away a tenth. Scribner subtracts a term that grows with the diameter, 2 times D plus 4, and multiplies the squared diameter by 0.79, which is a gentler deduction that still bites on small logs. International subtracts a slab allowance that grows with the diameter and adds taper back, so it tracks the log most closely at every size. The table in the next section shows the gap closing as logs get bigger: Doyle reads 79 percent under International on a 6-inch log, 34 percent under on a 12-inch log, 12 percent under on a 20-inch log, and by 30 inches the two rules agree within 1 percent. Past about 30 inches Doyle actually reads higher than International, because the fixed 4-inch deduction is then too small for the log. That crossover is the reason experienced buyers and sellers always name the rule: below it Doyle favors the buyer, above it Doyle favors the seller.
The three log rules, side by side
The table below shows all three rules for 16-foot logs from 6 to 40 inches at the small end. Every figure is a formula value, computed by the rules as this calculator applies them, rounded to the nearest board foot. Read across a row to see what one log is worth under each rule, and read down the last column to see the Doyle gap close as logs get bigger.
| Small-end diameter | Doyle | Scribner | International 1/4-inch | Doyle against International |
|---|---|---|---|---|
| 6 inches | 4 | 12 | 19 | 79% under |
| 8 inches | 16 | 31 | 39 | 59% under |
| 10 inches | 36 | 55 | 65 | 44% under |
| 12 inches | 64 | 86 | 97 | 34% under |
| 14 inches | 100 | 123 | 136 | 26% under |
| 16 inches | 144 | 166 | 181 | 20% under |
| 18 inches | 196 | 216 | 232 | 16% under |
| 20 inches | 256 | 272 | 290 | 12% under |
| 22 inches | 324 | 334 | 354 | 8% under |
| 24 inches | 400 | 403 | 424 | 6% under |
| 26 inches | 484 | 478 | 501 | 3% under |
| 28 inches | 576 | 559 | 584 | 1% under |
| 30 inches | 676 | 647 | 674 | Within 1% |
| 32 inches | 784 | 741 | 770 | 2% over |
| 34 inches | 900 | 841 | 872 | 3% over |
| 36 inches | 1024 | 948 | 981 | 4% over |
| 38 inches | 1156 | 1061 | 1096 | 5% over |
| 40 inches | 1296 | 1180 | 1218 | 6% over |
Three patterns in this table are worth studying. First, the Doyle gap shrinks steadily as logs get bigger, from 79 percent under on a 6-inch log to agreement near 30 inches and then a growing overrun past it. There are no reversals: at any fixed length, the Doyle shortfall falls with every inch of diameter. Second, Scribner does not always sit between the other two. It is the middle value on small and mid-size logs, but it falls below Doyle once the diameter passes about 25 inches, and on very large logs it is the lowest of the three: at 40 inches Scribner reads 1180 against Doyle's 1296 and International's 1218. Third, the three rules are closest together in the 24- to 30-inch range, where a 16-foot log reads within about 6 percent under any rule. That is the size range where the choice of rule matters least, and the small-log range where it matters most.
Length changes the picture less than diameter does, but it changes it. The table below holds the diameter at 12 inches and varies the length. Doyle and Scribner scale in exact proportion to length, because their formulas multiply by L over 16: a 12-inch log 8 feet long is exactly half the 16-foot value under both rules. International does not scale in exact proportion, because the taper allowance grows with length: the 8-foot value, 44 board feet, is less than half of the 16-foot value of 97, because the longer log gets more taper sections. The difference is small on one log and worth knowing on a load.
| Length | Doyle | Scribner | International 1/4-inch |
|---|---|---|---|
| 8 feet | 32 | 43 | 44 |
| 10 feet | 40 | 54 | 57 |
| 12 feet | 48 | 64 | 69 |
| 14 feet | 56 | 75 | 83 |
| 16 feet | 64 | 86 | 97 |
| 20 feet | 80 | 107 | 127 |
One more comparison matters when a contract is involved: formula values against published table values. The Doyle formula is the rule, so formula and table agree exactly. The International tables round to the nearest 5 board feet, so the table reads 95 where the formula gives 97 for a 12-inch, 16-foot log, and 180 where the formula gives 181 for a 16-inch, 16-foot log. The Scribner Decimal C table rounds to the nearest 10 and comes from the diagram rule rather than the formula, so the gaps are bigger: the table reads 80 where the formula gives 86 for a 12-inch, 16-foot log, and 160 where the formula gives 166 for a 16-inch, 16-foot log. These are not errors in either direction. The formula smooths the diagram rule's steps, and the table rounds the smoothed value. What matters is that both sides of a deal use the same reference, and that the reference is named in writing.
Why the three rules disagree
Every log rule has to answer the same three questions: how much wood does the saw blade destroy, how much wood comes off as slabs, and how much does the log widen from the small end to the big end. The three rules answer differently, and the differences explain the whole table above.
Saw kerf: the wood the blade eats
Kerf is the width of the cut the saw makes, the wood that becomes sawdust instead of lumber. A 1/4-inch kerf on a 1-inch board wastes a fifth of the wood in that board's share of the log, so the kerf allowance is the single biggest deduction after slabs. Doyle allows a 5/16-inch kerf, wider than modern saws need, which is one reason it under-scales. Scribner allows 1/4 inch, the kerf its diagram boards were drawn with. International allows 1/4 inch for the saw plus 1/16 inch for shrinkage as the lumber dries, which is why the handbook calls it the 1/4-inch rule even though the total allowance is 5/16 inch. The original International rule of 1906 assumed a 1/8-inch kerf, and Clark revised it in 1917 because most mills could not saw that fine. A modern thin-kerf band mill, cutting at 1/8 inch or less, will saw more lumber than any of the three rules credit, which is one source of overrun.
Slabs: squaring a round log
A log is round and lumber is square, so the outside of the log has to come off as slabs before any boards can be cut. Doyle deducts a fixed 4 inches from the diameter for slabs and edgings, which Virginia Cooperative Extension describes as about twice the normal amount. That fixed deduction is the whole story of Doyle's behavior: it is far too much on a small log and too little on a large one, so Doyle under-scales small logs and over-scales large logs, crossing the true value near 30 inches. Scribner makes no separate slab deduction: the diagram boards were fitted inside the circle, so the waste outside the boards is whatever the diagram left, which varies unevenly with diameter and produces the rule's characteristic steps. International deducts a 1-inch collar for slab, a fixed inch off the radius rather than a fixed amount off the diameter, plus a slab thickness that varies with the log diameter. The result is a deduction that scales with the log instead of fighting it.
Taper: the log is not a cylinder
Every log widens from the small end to the big end, and the extra wood in the wide end is real lumber. Doyle and Scribner both ignore taper entirely: they treat the log as a cylinder of the small-end diameter, which understates longer logs more than short ones. International assumes a fixed taper of 1/2 inch in diameter for every 4 feet of length, which is 2 inches over a 16-foot log, and works the rule section by section so the wider sections credit more wood. The assumption is conservative: it comes from Clark's studies of northeastern species, and the Forest Service handbook directs scalers to cap the scaling length at 16 feet where local timber averages 3 inches or more of taper in 16 feet, because the rule's taper allowance would then understate the log. A log with more taper than the rule assumes will saw more lumber than the rule credits, and a log with less taper will saw less. Taper is also why the International rule is the only one of the three that cannot be written as a single simple formula in D and L: the section-by-section working is the rule, and the single-formula versions, including Grosenbaugh's 1952 integrated formula, are approximations of it.
A short history of the three rules
Doyle is the oldest, published by Edward Doyle of Rochester, New York, most likely in 1825, though no copies of that first edition survive and the earliest surviving edition is the second, from 1837. It spread because it is easy to remember and easy to compute in the woods, and it is still the most widely used rule on private timber in the East and South. Scribner followed in 1846, when J. M. Scribner published his diagram rule for 1-inch lumber in 4-, 6-, and 8-inch widths. It became the standard of the Forest Service in the Lake States and the West, and in its Decimal C form it is still the default rule on many federal timber sales west of the Mississippi, though the Forest Service has moved much of its scaling to cubic volume. The International rule was developed by Judson F. Clark while he worked for the Province of Ontario, first published in 1906 and revised to the 1/4-inch kerf in 1917. It is the youngest rule and the most accurate, but it has found the least use, largely because its section-by-section working is harder to do by hand than Doyle's single formula. Over 95 log rules bearing about 185 names have been developed in the United States and Canada, but only these three are widely recognized and in current use.
Which rule should you use?
There is no single right rule, and Purdue Extension says so plainly: local tradition will most likely predict which rule is used in buying and selling cut logs, and the rules are fair as long as everyone uses the same rule. The practical guidance below follows the published sources, not any preference of this calculator.
Doyle is the rule of private hardwood timber in the East, South, and Midwest, and the rule most small sawmills and log buyers in those regions will quote. If you sell hardwood logs to a local buyer, expect Doyle, and expect the buyer to know exactly how much overrun to expect on your logs: the buyer's price per thousand board feet already accounts for the fact that Doyle under-scales small logs, because the mill will saw more lumber than the Doyle scale credits. The danger for a seller is not Doyle itself but quoting a Doyle price against an International scale, or the other way around. If you are selling small logs, ask what the buyer would pay on the International scale as well, so you can see the size of the gap before you agree.
Scribner is the rule of the West: softwood sawlogs in the Pacific Northwest, the Inland West, and the Rockies are usually bought and sold on Scribner Decimal C, and it remains the default rule on many Forest Service timber sales there. If your buyer or your contract names Scribner, ask whether it means the Decimal C table or the formula, because the two differ by a few board feet on most logs and the table governs when it is named. Scribner has no taper allowance, so it under-scales long logs more than short ones, and its step behavior means two logs an inch apart in diameter can scale the same: Purdue notes that a 10-inch log reads 30 board feet on the Decimal C scale at every length from 8 to 12 feet.
International 1/4-inch is the rule to use when the objective is to estimate as closely as possible the volume of lumber a log will actually produce. Purdue says so directly, and the Forest Service uses it where the log scale should come close to the lumber tally. It is the standard for timber cruising in much of the East, and several eastern states use it for state timber sales. Its disadvantage is only its unfamiliarity in regions where Doyle or Scribner is the local habit: a buyer who has always paid by Doyle will not switch rules because a seller asks, and the price per thousand board feet is set with the rule in mind, so switching rules without switching the price would change the deal.
Whichever rule you use, name it in writing. A price per thousand board feet means nothing without the rule behind it. A buyer who buys by Doyle and sells by International at the same price per thousand makes 25 percent on the turn with no change in price: a 16-inch, 16-foot log scales 144 board feet by Doyle and 180 by the International table, and 180 divided by 144 is 1.25. The reverse turn loses the same amount. Put the rule, the scaling diameter, the length, and the trim allowance in the sale agreement, and keep a tally sheet with each log's diameter and length so either side can rework the scale. Our Timber Value Calculator prices a scaled log once you have the board feet, so you can compare what the same logs are worth under each rule at the price your buyer offers.
How to measure a log
The calculator's answer is only as good as the two measurements that go into it, and the diameter matters far more than the length: every rule squares the diameter, so an inch of error on a 12-inch log moves the answer by about a sixth, while a foot of error on a 16-foot log moves it by about a sixteenth. Measure carefully, and measure in the order a scaler does: diameter first, then length.
Diameter: small end, inside the bark, two ways
Measure at the small end of the log, across the end grain, inside the bark. The small end governs because a board can be no wider than the narrowest part of the log it comes from. Bark is not lumber, so measure inside it: chip a small notch in the bark at the point of measurement, or measure the bark thickness and subtract twice that amount from the outside diameter. Penn State's guidance is to take two diameter readings at right angles to each other and average them, because logs are often oval, and to measure at the small end for scaling. Where a log is not round, the two-reading average is a far better estimate than a single reading across the wide way.
The standard field tool is a Biltmore stick, a graduated stick held against the log at a fixed distance, which reads diameter directly from the geometry of similar triangles. A steel tape works too, and so does a diameter tape, which reads diameter from circumference: wrap it around the log, and the diameter is the reading where the tape meets zero. Whatever you use, measure with the log on the ground and the stick or tape held square across the end, not at an angle, because a diagonal measurement reads longer than the true diameter. A log that is still standing is a different problem: our Tree Height Calculator estimates the height of a standing tree, which is the first step in deciding how many logs the tree will make and how long they will be, before the saw ever touches it.
Length: a tape, and know your trim
Measure the length with a tape along the center of the log, from end to end, and note the trim allowance separately. Logs are cut in even lengths, most commonly 8 to 16 feet, with about 4 inches of extra length left on the end so the mill can square the ends and take off any splitting. A log measured at 16 feet 4 inches is a 16-foot log, not a 16-foot-4-inch log: the trim is not scaled. A log just short of a full foot length is tallied at the next lower foot length in hardwoods, so a log measuring 15 feet 11 inches scales as a 15-foot log. If the log is crooked, the scaling length is the longest straight length the mill can saw, not the length along the curve, and if the log is so crooked that no straight length can be cut, the mill may reject it or scale it back sharply.
Defects, cull, and the scaler's judgment
Log scaling is partly judgment, and the judgment matters most on defective logs. Rot in the center, sweep, crook, knots, and end splits all reduce the lumber a log will saw, and a scaler accounts for them, most often by reducing the length of the log in the scale, and sometimes by reducing the diameter. Purdue reports an experiment in which 14 timbermen scaled the same 11 logs and came up with volumes ranging from 1,434 to 1,795 board feet, with a mean of 1,589. The spread was 361 board feet, about 23 percent of the mean, and it came entirely from judgment calls on the same logs. That spread is the honest measure of what scaling is: a skilled estimate, not a precise measurement. Two competent scalers can differ, and the rules are fair as long as both sides use the same one and accept that the scale is an estimate.
When a log has a visible defect, scale it as the scaler would: deduct for the defect before you enter the numbers, by shortening the length or reducing the diameter to match the sound wood. A log with a large knot cluster on one side may lose a foot or two of length in the scale. A log with rot in the center may lose several inches of effective diameter. A hollow log, a log with metal in it, or a log with a bad split may be worth nothing as a sawlog and is best cut for firewood or pulp. No calculator can make these calls; they take a look at the log.
From one log to a load
One log is a curiosity; a load is a business. Scaling a load means tallying every log, applying the same rule to each, and adding the results. The standard unit for pricing is the thousand board feet, written MBF, and a truckload of hardwood sawlogs runs roughly 3,000 to 6,000 board feet, depending on the size of the logs and the size of the truck. A load of twenty 16-inch, 16-foot logs scales 2,880 board feet by Doyle, 3,320 by Scribner, and 3,620 by International, and at 500 dollars per MBF the same load is worth 1,440 dollars on the Doyle scale, 1,660 on the Scribner formula scale, and 1,810 on the International formula scale. The gap between the Doyle price and the International price is 370 dollars on one load, which is why the rule is the first thing a sale agreement should name, before the price.
The working matters as much as the total. Keep a tally sheet with each log's diameter and length, and the rule you applied, so either side can rework the scale from the measurements. A tally sheet that lists only the total board feet is worthless in a dispute, because it cannot be checked. Enter the logs in the calculator one size at a time: a pile of identical logs can go in as one entry with the log count, and mixed sizes go in as separate entries. The totals the calculator prints for each size add up to the load total, and the steps print the working for every size, so the whole tally can be verified line by line.
Overrun: the mill saws more than the scale says
Overrun is the difference between the lumber the mill actually saws from a log and the board feet the log rule credited it with, expressed as a percentage: overrun equals the mill tally minus the log scale, divided by the log scale, times 100. If a mill saws 120 board feet of lumber from a log that scaled 100, the overrun is 20 percent. Overrun is not a mistake; it is the expected result of rules that allow for more kerf and more slab than a modern mill uses. A thin-kerf band mill sawing 1/8-inch kerf against a rule that allows 1/4 inch will overrun by roughly the kerf difference alone. Doyle overruns more than the other rules, because its slab deduction is about twice the normal amount and it ignores taper, and the overrun is largest on small logs, where the deductions are largest relative to the log. Overrun is not the same as profit: the mill's price per thousand board feet already reflects the expected overrun, and a buyer who pays a Doyle price is paying for the lumber the Doyle scale credits plus the overrun the mill expects to get. When you compare prices from different buyers, compare them on the same rule, because a price per MBF without a rule is not a price at all.
What a load is worth
Log prices vary by species, grade, region, and market, and a board-foot figure is only half of the value: a thousand board feet of walnut veneer logs is worth many times a thousand board feet of low-grade oak, and a log that makes one clear 16-foot board is worth more than the same board feet in short, knotty pieces. The calculator gives you the volume; the price comes from the market. For a rough sense of scale, Northern Woodlands reported a 17-inch, 16-foot maple log scaling 205 board feet by International 1/4-inch, and at 500 dollars per MBF that log is worth about 102 dollars on the International scale. The same log scales 169 board feet by Doyle and 190 by the Scribner formula, worth about 84 and 95 dollars at the same price, and the 18-dollar gap between the Doyle and International values on one log is the whole argument in miniature. If you are deciding whether to sell a woodlot, plant a new stand, or manage an existing one, the volume and the value belong in the same calculation: our Tree Planting Calculator works out how many trees a piece of ground will hold and what spacing they need, and the timber value work belongs after the volume work, not before it.
Board feet in a log vs board feet in lumber
The log rules estimate how much lumber comes out of a round log. Once the wood is lumber, a different and much simpler rule applies: the board feet in a board equal the thickness in inches times the width in inches times the length in feet, divided by 12. A board 1 inch thick, 8 inches wide, and 12 feet long holds 8 board feet: 1 times 8 times 12, divided by 12. A board 2 inches thick, 10 inches wide, and 16 feet long holds 26.67 board feet: 2 times 10 times 16, divided by 12. This is an exact measurement of the lumber, not an estimate, and it is how lumber is sold at a yard.
Do not use the lumber rule on a log, and do not use a log rule on lumber. The lumber rule applied to a log would need a thickness and a width the log does not have, and the log rules applied to a board would deduct for kerf and slabs that were already taken out at the mill. The confusion is common: a landowner who measures a log's length and diameter, treats the diameter as a width, and applies the lumber rule will get a number far higher than any log rule gives, and will be disappointed at the mill. The gap between the two answers is the wood the saw turns into sawdust and slabs, and it is real wood, not a rounding error. On a 12-inch, 16-foot log, the cylinder of wood holds about 12.57 cubic feet, which is about 151 board feet of wood if you could cut it with no waste at all, against the 97 board feet the International rule credits and the 64 the Doyle rule credits. The difference between 151 and 97 is the kerf, the slabs, and the taper that the rule accounts for, and the difference between 97 and 64 is the extra caution in Doyle's 4-inch deduction. None of that wood is lost to fraud; it is the price of turning a round log into square lumber.
The same boundary applies to firewood, which is sold by the cord, not by the board foot. A standard cord is a stack 4 feet high, 4 feet wide, and 8 feet long, 128 cubic feet of stacked wood including the air between the pieces, and a cord of hardwood weighs roughly 2 to 3 tons depending on the species and the moisture. A sawlog scaled in board feet and a firewood log sold by the cord are two different products at two different prices, and the sawlog is worth far more per cubic foot. If a log is sound enough to saw, selling it as firewood wastes its value; if it is too small, too crooked, or too defective to saw, the board-foot scale is the wrong measure and the cord is the right one.
Sources
- Purdue Extension, FNR-191, Log and Tree Scaling Techniques, by Daniel L. Cassens. The Doyle and Scribner formulas, the International section formulas, the history of the rules, and the scaler-judgment test are all from this publication. extension.purdue.edu
- USDA Forest Service, National Forest Log Scaling Handbook, FSH 2409.11, Chapter 70, Scaling Rules. The International rule as a formula applied to each 4-foot section with a 1/2-inch taper allowance, the 20-foot scaling length limit, the 1-inch slab collar, and the International Decimal rule are from this chapter. fs.usda.gov
- USDA Forest Service, National Forest Log Scaling Handbook, FSH 2409.11, full handbook. fs.usda.gov
- Virginia Cooperative Extension, publication 420-085, Forest Landowner's Guide to the Measurement of Timber and Logs. The comparison table for 16-foot logs, the Doyle kerf and slab allowances, and the Decimal C rounding example are from this guide. pubs.ext.vt.edu
- Penn State Extension, Forest Measurement. Measuring the small-end diameter in two directions and averaging, cutting logs in even lengths with a trim allowance, and the summary of the three rules are from this lesson. ecosystems.psu.edu
- Northern Woodlands, Measuring Wood Volumes. The 17-inch, 16-foot maple log scaling 205 board feet by International 1/4-inch is from this article. northernwoodlands.org
- University of Tennessee Extension, publication PB 1650. The Doyle formula and scaling methods are from this publication. woodweb.com
Frequently asked questions
How many board feet are in a 12-inch, 16-foot log?
It depends on the rule: 64 board feet by Doyle, 86 by Scribner, and 97 by the International 1/4-inch rule. The Doyle formula, (12 minus 4) squared times 16 divided by 16, gives 64; the Scribner formula gives 85.76, rounded to 86; and the International rule, worked in four 4-foot sections with a 1/2-inch taper allowance at each section, gives 96.91, rounded to 97. The published tables read a little lower because they round: the International table rounds to the nearest 5, giving 95, and the Scribner Decimal C table rounds to the nearest 10, giving 80.
Which log rule should I use when selling timber?
Use the rule your buyer and your region already use, and name it in the sale agreement. Doyle is the usual rule for private hardwood timber in the East, South, and Midwest; Scribner Decimal C is the usual rule for softwood in the West and on many federal timber sales; and the International 1/4-inch rule is the most accurate estimate of the lumber a log will actually saw. A price per thousand board feet means nothing without the rule behind it, because the same logs scale very differently under each rule.
Why does Doyle give so much less than International on small logs?
Doyle subtracts a fixed 4 inches from the diameter before squaring it, to allow for slabs and edgings, and that fixed deduction takes a much bigger share of a small log than of a large one. On a 6-inch log it removes two thirds of the diameter, so a 6-inch, 16-foot log scales only 4 board feet by Doyle against 19 by International, a gap of 79 percent. On a 40-inch log the same 4 inches remove only a tenth of the diameter, and Doyle reads 6 percent over International.
What is the Scribner Decimal C rule?
Scribner Decimal C is the most common form of the Scribner rule. The original Scribner rule is a diagram rule, drawn from 1-inch boards fitted inside circles, and Decimal C rounds its table values to the nearest 10 board feet. The formula used by this calculator, (0.79 times D squared minus 2 times D minus 4) times L divided by 16, was published by Bruce and Schumacher in 1950 to smooth the diagram rule's steps; it follows the table within a few board feet, reading 86 where the table reads 80 on a 12-inch, 16-foot log. When a contract names the Scribner table, the table governs.
How do you measure a log for scaling?
Measure the diameter across the small end of the log, inside the bark, in two directions at right angles, and average the two readings. Measure the length with a tape along the center of the log, and do not include the trim allowance, the extra few inches left on the end so the mill can square it. A log just short of a full foot length is tallied at the next lower foot length in hardwoods, and a crooked log is scaled on its longest straight length, not its length along the curve.
What is overrun?
Overrun is the lumber a mill saws beyond what the log rule credited, expressed as a percentage: the mill tally minus the log scale, divided by the log scale, times 100. If a mill saws 120 board feet of lumber from a log that scaled 100, the overrun is 20 percent. Overrun is expected, not a mistake, because the rules allow for more kerf and more slab than a modern mill uses, and it is largest on small logs under the Doyle rule. The price per thousand board feet already reflects the expected overrun, so overrun is not free profit.
Can I use this calculator for lumber?
No. Log rules estimate how much lumber comes out of a round log, allowing for saw kerf, slabs, and taper. Lumber is measured exactly: the board feet in a board equal the thickness in inches times the width in inches times the length in feet, divided by 12. A board 1 inch thick, 8 inches wide, and 12 feet long holds 8 board feet. Applying a log rule to lumber would deduct for waste that was already taken out at the mill, and applying the lumber rule to a log ignores the waste altogether.
How accurate is a log rule?
A log rule is a skilled estimate, not a precise measurement. The International 1/4-inch rule comes closest to the lumber a log will actually saw, because it allows for taper and uses realistic kerf and slab deductions, but no rule can account for defects a scaler cannot see. In one test reported by Purdue Extension, 14 timbermen scaled the same 11 logs and their totals ranged from 1,434 to 1,795 board feet, a spread of 361 board feet around a mean of 1,589. Two competent scalers can differ, and the rules are fair as long as both sides use the same one.