Phone Charging Time Calculator
Time to a full charge
Time to 80%
The last 20% (taper)
Charge curve: battery level over time
Same phone, different charger
Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.
How to use the Phone Charging Time Calculator
How long does it take to charge a phone? The honest answer is that it depends on three things: the size of the battery, the power of the charger, and how full the battery already is. A 5,000 mAh phone on an old 5W brick takes more than six hours to fill from empty, while the same phone on a 45W charger finishes in about an hour. This phone charging time calculator works out both numbers that matter: the time to 80%, where fast charging does its work, and the time to a full 100%, including the slow taper at the end. It takes less than a minute.
- Pick your phone, or enter the battery size. If you have an iPhone 16, a Galaxy S25, a Galaxy S25 Ultra, or a Pixel 9, pick it from the list and the calculator fills in its published battery size and its maximum charging draw. Any other phone works too: choose Other phone and type the battery size in mAh from your settings or the manufacturer's spec page. Most current phones sit between 3,500 and 5,500 mAh.
- Set the charger power. Tap one of the preset chips (5W, 18W, 20W USB-PD, 25W, 30W, 45W, 65W) or type your own wattage. The wattage is printed on the charger brick, usually in small print near the prongs. A phone never draws more than its own limit, so the calculator caps the power at what your phone can actually take: a 65W charger charges a Galaxy S25 no faster than a 25W one.
- Say whether you are charging wired or wireless. Wireless charging loses more energy as heat, so the same wattage takes longer without a cable. The calculator uses 75% efficiency for wireless against 90% for wired, from published Qi efficiency ranges of 70 to 80%. Wireless also caps lower: 25W on an iPhone 16 with MagSafe, 15W on a Galaxy S25 or a Pixel 9.
- Enter the current charge. Drag the slider or type the number. Starting from 0% shows the full charge time; starting from 20% or 50% shows the top-up time. Starting above 80% is the interesting case: the whole remaining charge runs at the slow taper rate, so the last few percent take far longer than the first few did.
- Read your result. You get the time to a full charge in big numbers, the time to 80% and the taper time side by side, a charge curve showing the battery level over time with the taper marked, a comparison of the same phone on three different chargers, and the working: battery energy in watt-hours, average power below and above 80%, and any warnings, such as a charger whose extra wattage your phone cannot use.
This calculator is one of the free tools on Tools Elite. Every figure on this page comes from a published source listed at the bottom: GSMArena lab tests, PhoneArena charging tests, Apple and Samsung and Google specifications, Battery University, and the USB Implementers Forum's USB Power Delivery documentation. The model is calibrated against six published full-charge measurements, and the calibration table in the How it works section shows where it lands against each one, including the phones where it runs optimistic. If your phone is often low when you leave the house, our Power Bank Capacity Planner works out what size power bank you need, and our Laptop Charger Wattage Checker answers the same wattage question for a laptop. The calculator gives estimates for general guidance, not a guarantee for any one phone, so always check the manufacturer's specifications for the phone and charger you own.
How it works
The calculator works in five steps: it turns the battery size into energy, it caps the charger power at what the phone can draw, it applies a sustained-power factor and an efficiency factor, it splits the charge into a fast phase below 80% and a taper phase above 80%, and it divides the energy in each phase by the average power in that phase.
Step 1: battery size becomes energy. A battery rated at 5,000 mAh holds 5,000 milliamp-hours of charge, but charging time depends on energy, which needs a voltage. Phone cells are lithium-ion with a nominal voltage of 3.7 V, the standard figure for NMC chemistry. Apple publishes no watt-hour rating for the iPhone 16, and teardown-derived figures of about 13.7 to 13.9 Wh imply a nominal voltage nearer 3.85 V for Apple's cell, so the 3.7 V figure understates iPhone energy by about 4 to 5 percent — one contributor to the iPhone calibration miss. So a 5,000 mAh battery holds 5,000 times 3.7 divided by 1,000, which is 18.5 Wh. An iPhone 16 at 3,561 mAh holds 13.2 Wh, a Galaxy S25 at 4,000 mAh holds 14.8 Wh, and a Pixel 9 at 4,700 mAh holds 17.4 Wh. One rival calculator uses 3.85 V instead of 3.7 V, which would raise every time on this page by about 4%: the sources disagree by that much, and the calculator states its choice openly.
Step 2: the phone caps the charger. The peak power is the lower of the charger wattage and the phone's maximum draw. An iPhone 16 caps at 27W wired (Apple publishes no figure; lab tests put the sustained draw at about 27W, with peaks near 30W and one report putting standard models near 20W, so the published range is 20 to 30W and the calculator uses the middle of the sustained figures). A Galaxy S25 caps at 25W, a Galaxy S25 Ultra at 45W, and a Pixel 9 at 27W. A phone with no preset is assumed to cap at 30W wired, the middle of the 25 to 45W band most current phones sit in. Wireless caps are lower: 25W on an iPhone 16 with MagSafe, 15W on a Galaxy S25, a Galaxy S25 Ultra, or a Pixel 9, and 15W assumed for a generic phone.
Step 3: peak power becomes average power. No phone holds its peak wattage for the whole charge. GSMArena's 30-minute checkpoints show it: a Galaxy S25 Ultra on a 45W charger reaches 72% in 30 minutes, which is an average of about 27W over that half hour, or 60% of the 45W peak. A Galaxy S25 on a 25W charger reaches 56% in 30 minutes, about 17W average, or 66% of peak. An iPhone 16 on a 20W charger reaches about 60% in 30 minutes, about 16W average, or 79% of peak. The calculator models this with a sustain factor that falls as the peak rises: 0.94 at 5W, where the charger is the limit and the phone draws nearly all of it, down to 0.67 at 45W and above, where the phone's own curve dominates. On top of that sits efficiency: 90% for wired charging, from the published 90 to 95% range for wired USB-C charging, and 75% for wireless, the middle of the published 70 to 80% range for Qi.
Step 4: the charge splits at 80%. Lithium-ion batteries charge in two stages, constant current then constant voltage, and the switch lands around 70 to 80% depending on the phone. Below 80% the phone takes the average power from step 3. Above 80% it tapers: the calculator uses 30% of the fast-phase average power for the taper phase. That figure comes from five published charging tests, where the measured taper power ran from about 25% to 32% of the fast-phase average: about 32% on the Galaxy S25 and S25 Ultra, and about 25% on the iPhone 16, the iPhone 16 Plus, and the Pixel 9. The calculator uses 30% as a rounded central value and says so, rather than pretending the taper is the same on every phone.
Step 5: time is energy divided by power, per phase. The time to 80% is the energy between the starting charge and 80% divided by the fast-phase average power. The time from 80% to full is the remaining 20% of the battery energy divided by the taper power. Starting above 80% skips the fast phase entirely. Times are rounded to whole minutes.
Worked example 1: a 5,000 mAh phone on a 20W USB-PD charger, from 0%. Energy is 18.5 Wh. Peak power is 20W. The sustain factor at 20W is 0.84, so the fast-phase average is 20 times 0.84 times 0.90, which is 15.1W, and the taper average is 30% of that, 4.5W. Time to 80% is 80% of 18.5 Wh, which is 14.8 Wh, divided by 15.1W, which is 0.98 hours, or 59 minutes. The last 20% is 3.7 Wh divided by 4.5W, which is 0.82 hours, or 49 minutes. Total: 1 hour 48 minutes, with the taper taking 45% of the total time. The naive division, 18.5 Wh divided by 20W, gives 56 minutes, but that assumes the charger delivers its full rating to the battery with no losses and no taper, which no phone does: measured full-charge averages run 39 to 46% of the charger rating across the four phones the tool presets.
Worked example 2: an iPhone 16 on a 20W charger, from 0%. Energy is 13.2 Wh. Peak power is 20W, below the phone's 27W cap. Fast-phase average is 15.1W and taper average is 4.5W, the same as example 1 because the charger is the same. Time to 80% is 80% of 13.2 Wh, which is 10.5 Wh, divided by 15.1W, which is 42 minutes. The last 20% is 2.6 Wh divided by 4.5W, which is 35 minutes. Total: 1 hour 17 minutes. GSMArena measured 1 hour 42 minutes for the iPhone 16 on a 45W PD charger, with 59% at 30 minutes and 85% at one hour, so the calculator is 25% optimistic here: the iPhone taper is the deepest measured, and the model says so rather than hiding it.
Worked example 3: a Galaxy S25 Ultra on a 45W charger, from 0%. Energy is 18.5 Wh. Peak power is 45W. The sustain factor at 45W is 0.67, so the fast-phase average is 45 times 0.67 times 0.90, which is 27.1W, and the taper average is 8.1W. Time to 80% is 14.8 Wh divided by 27.1W, which is 33 minutes. The last 20% is 3.7 Wh divided by 8.1W, which is 27 minutes. Total: 60 minutes. GSMArena measured 59 minutes for the S25 Ultra on Samsung's 45W adapter, with 72% at 30 minutes and 41% at 15 minutes, so the calculator lands within 2% on this phone: the closest calibration point.
Worked example 4: a 5,000 mAh phone on an old 5W brick, from 0%. Energy is 18.5 Wh. Peak power is 5W, sustain 0.94, so the fast-phase average is 5 times 0.94 times 0.90, which is 4.2W, and the taper average is 1.3W. Time to 80% is 14.8 Wh divided by 4.2W, which is 3 hours 30 minutes. The last 20% is 3.7 Wh divided by 1.3W, which is 2 hours 55 minutes. Total: 6 hours 25 minutes. The naive division, 18.5 Wh divided by 5W, gives 3 hours 42 minutes, and one rival calculator quotes about 3.5 hours, but that figure assumes no losses and no taper, which no real phone achieves. Published estimates for a 5,000 mAh battery on 5W run from 4 to 6 hours, and one battery guide puts it at about 6 hours, which is where the calculator lands.
Calibration: the model against six published measurements. The table below compares the calculator against every full-charge time used to build it. The model fits Samsung's curve closely, runs 6 to 19% optimistic on the Pixel 9, and 25% optimistic on the iPhone 16, because both of those phones taper harder than the model's 30% figure. The iPhone 16 Plus is the worst case: GSMArena measured 1 hour 39 minutes for it on a 45W charger, against a model figure of about 1 hour 13 minutes, because its last 15% alone took about 40 minutes. No single taper figure fits every brand, and the calculator shows its misses instead of tuning the model to one phone and hiding the rest.
| Phone and charger | Battery | Measured full charge | Calculator | Difference |
|---|---|---|---|---|
| Galaxy S25 Ultra, 45W | 5,000 mAh | 59 min (GSMArena) | 60 min | 2% slow |
| Galaxy S25 Plus, 45W | 4,900 mAh | 58 min (GSMArena) | 59 min | 2% slow |
| Galaxy S25, 25W | 4,000 mAh | 77 min (GSMArena) | 72 min | 6% fast |
| iPhone 16, 20W | 3,561 mAh | 102 min (GSMArena) | 77 min | 25% fast |
| Pixel 9, 30W | 4,700 mAh | 85 to 99 min (three testers) | 80 min | 6 to 19% fast |
| iPhone 16 Plus, 45W | 4,674 mAh | 99 min (GSMArena) | 73 min | 26% fast |
What the calculator does not do. It does not model temperature: a phone charging in a hot car or in direct sun throttles its draw and takes longer, and the calculator has no temperature input. It does not model battery age: an old battery with reduced capacity fills faster in minutes but holds less charge, and the calculator assumes a healthy battery at its rated size. It does not model use during charging: playing a game while plugged in draws power away from the battery and stretches the time. It does not model optimized charging features, such as Apple's Optimized Battery Charging or Samsung's Adaptive protection, which deliberately hold the battery below full until morning. And it does not cover tablets, laptops, or earbuds, which have different battery sizes and different charging curves.
What your result means
The time to 80% is the number that matters most days. That is the fast part of the charge, and it is the part you feel when you plug in for half an hour before leaving the house. On a 20W charger a 5,000 mAh phone reaches 80% in 59 minutes; on a 45W charger a Galaxy S25 Ultra gets there in 33 minutes. If you only need enough charge to get through the evening, the time to 80% is your number, and the time to full is a luxury.
The time to full is longer than the time to 80% suggests. The last 20% takes 45 to 52% of the total time in the calculator's model, depending on the starting charge, because the taper power is less than a third of the fast-phase power. On a 20W charger the last 20% of a 5,000 mAh battery takes 49 minutes, nearly as long as the first 80% took. Anyone who has watched a phone sit at 97% for what feels like forever has met the taper: the final few percent are the slowest of the whole charge.
The average power tells you what the charger rating hides. A 45W charger does not deliver 45W to the battery. On a Galaxy S25 Ultra the calculator's fast-phase average is 27.1W, which is 60% of the rating, and GSMArena's measurements back that up: 72% in 30 minutes works out to about 27W average over that half hour. A 20W charger averages 15.1W on the same math, and a 5W charger averages 4.2W. The gap between the number on the brick and the number in the battery is the whole reason a calculator beats a division sum.
The cap warning tells you when a bigger charger is wasted money. If the result says your phone caps its draw below your charger wattage, buying a bigger charger changes nothing. A Galaxy S25 on a 65W charger charges in exactly the same time as on a 25W charger, because the phone takes 25W and no more. The comparison cards show it directly: for a generic phone, 30W, 45W, and 65W all give the same 1 hour 18 minutes, because the generic cap is 30W. The money is better spent on a second charger for the office than on a bigger one for the phone you already own.
The charge curve shows the taper at a glance. The blue part of the curve climbs steeply to 80%, and the orange part flattens out toward 100%. The dashed line marks where the taper starts. If your curve is mostly orange, you started above 80% and there is no fast phase left: that is normal, and it is why topping up from 85% to 100% feels so slow. If your curve is mostly blue, you started low and the charger is doing its best work.
The comparison cards answer the upgrade question. Each card shows the same phone on a different charger, with how much faster or slower it is than the charger you picked. A 5,000 mAh phone on a 5W brick takes 6 hours 25 minutes; the same phone on a 20W USB-PD charger takes 1 hour 48 minutes, saving 4 hours 37 minutes. Going from 20W to 45W on a generic phone saves 30 minutes, because the generic cap is 30W. Going from 20W to 45W on a Galaxy S25 Ultra saves 48 minutes, because that phone can actually use 45W. The value of a faster charger depends entirely on the phone it is plugged into.
Phone charging speeds explained
Charger wattages look like a simple ladder, 5W to 65W and beyond, but the ladder has three catches: the phone caps the draw, the average power is well below the peak, and the taper eats the end of every charge. The table below shows what each charger actually does to a 5,000 mAh generic phone from 0%, using the calculator's model. The generic cap of 30W is why the 30W, 45W, and 65W rows are identical: a phone that can use 45W, such as the Galaxy S25 Ultra, finishes in 60 minutes on a 45W charger instead.
| Charger | Typical source | Time to 80% | Time to full |
|---|---|---|---|
| 5W | Old USB-A brick, laptop USB port | 3 hr 30 min | 6 hr 25 min |
| 10W | 5V/2A brick, older fast charger | 1 hr 49 min | 3 hr 20 min |
| 15W | Samsung Adaptive Fast Charging | 1 hr 15 min | 2 hr 18 min |
| 18W | USB-PD, Quick Charge 3.0 | 1 hr 4 min | 1 hr 58 min |
| 20W USB-PD | Apple 20W adapter, standard PD brick | 59 min | 1 hr 48 min |
| 25W | Samsung 25W Super Fast Charging | 49 min | 1 hr 30 min |
| 30W | Google 30W charger, PD laptop brick | 43 min | 1 hr 18 min |
| 45W | Samsung 45W Super Fast Charging 2.0 | 43 min | 1 hr 18 min |
| 65W | Multi-port GaN laptop charger | 43 min | 1 hr 18 min |
Notice how the gains shrink as the wattage grows. Going from 5W to 10W saves 3 hours 5 minutes. Going from 10W to 20W saves 1 hour 32 minutes. Going from 20W to 30W saves 30 minutes. Going from 30W to 65W saves nothing at all on a generic phone, because the phone caps at 30W. That is the shape of charging: the jump from a slow brick to a fast one is enormous, and the jump from a fast brick to a faster one is small or zero. Most people get nearly all the benefit from a 20W or 25W charger, and the rest is marketing.
USB Power Delivery is the standard behind the fast rows. USB-PD is the USB Implementers Forum's open standard for negotiating power over USB-C. The charger and the phone agree on a voltage and current, and the power is the product of the two. The fixed voltage tiers are 5V, 9V, 15V, and 20V, with up to 100W in the Standard Power Range; USB-PD 3.1 added Extended Power Range tiers at 28V, 36V, and 48V, up to 240W, but those are for laptops, not phones. A 20W charger offers two tiers: 5V at up to 3A (15W) and 9V at up to 2.22A (20W). The phone picks the tier that suits it. The part that matters most for phones is Programmable Power Supply, or PPS, which lets the phone request any voltage between 3.3V and 21V in 20mV steps and adjust it as the battery fills. Samsung's 25W and 45W Super Fast Charging and Google's Pixel charging both need PPS: a plain 45W PD charger without PPS charges a Galaxy S25 Ultra more slowly than Samsung's own 45W adapter, because the phone cannot fine-tune the voltage.
The cable can cap the charge too. A standard USB-C cable is rated for 3A, which caps power at 60W at 20V; above that you need a 5A cable with an electronic marker chip. For phones the cable rarely matters at 20W or 25W, but it mattered for Samsung's 45W charging: the Galaxy S24 generation needed a 5A cable for full speed, and GSMArena found the Galaxy S25 Ultra no longer does, reaching a 39W peak on the ordinary 3A cable in the box. A frayed or bargain cable can still slow a charge by dropping voltage, so if a known-good charger suddenly charges slowly, the cable is the first thing to swap.
Why charging slows down after 80%
The slowdown is not a bug and it is not your charger failing. It is how lithium-ion batteries are charged, by design, and every phone does it. The standard method is called constant current, constant voltage, or CC-CV, and Battery University describes it as the standard method for lithium-based batteries. In the first stage the charger pushes a steady high current into the battery while the voltage climbs. In the second stage the battery has reached its maximum safe voltage, about 4.2V per cell, and the charger holds that voltage and lets the current fall as the battery fills. Charging ends when the current drops to about 3% of the rated current. The switch between the stages lands around 70 to 80% on most phones, which is why 80% is where the slowdown becomes obvious.
Battery University adds a warning that matters for fast charging: increasing the charge current does not hasten the full-charge state by much. A higher current fills the battery to about 70% quickly, but the saturation charge in stage two takes longer accordingly. That is why a 45W charger is dramatically faster than a 20W charger to 50% but only modestly faster to 100%: the taper phase does not speed up in proportion to the charger. At a 1C charge rate, a typical cell takes about 60 minutes of constant current to reach the voltage limit and then about 30 minutes of taper to fill the last 20%, so the last fifth of the battery takes a third of the total time even before phone software gets involved.
Phone software makes the taper deeper than the bare cell chemistry. The measured numbers tell the story. GSMArena's iPhone 16 Plus test reached 85% in one hour on a 45W charger, and then the last 15% took about 40 minutes, at an average power of roughly a quarter of the fast-phase average. The Galaxy S25 reached 56% in 30 minutes and finished in 77 minutes, which puts its taper power at about a third of its fast-phase average. The Pixel 9 reached 55% in 30 minutes and finished in 85 to 99 minutes across three testers, which puts its taper power at about a quarter of its fast-phase average. Across the five phones with published curves, the taper power runs from about 25% to 32% of the fast-phase average, and the calculator uses 30% as its central figure.
Manufacturers know the taper is slow, and they have built features around it. Apple's iOS 18 lets you set a charge limit between 80% and 100%, and Samsung's battery protection offers Maximum limits of 80%, 85%, 90%, or 95%. Both exist because keeping a battery below full reduces voltage stress and extends its life: Battery University notes that it is better not to fully charge a lithium-ion battery, because a high voltage stresses it. If you charge overnight, stopping at 80% saves the slowest part of the charge and is kinder to the battery; the calculator's time-to-80% figure is the one to use for that routine.
Wired vs wireless charging
Wireless charging trades speed and efficiency for convenience, and the trade is bigger than most people expect. A wired USB-C charger delivers 90 to 95% of the wall power to the battery, with the rest lost as a little heat in the cable and the charging circuit. A Qi wireless pad delivers 70 to 80%, and a Qi2 pad with magnetic alignment delivers 80 to 85%, with the rest lost as heat in the coils on both sides. The International Energy Agency's report on wireless charging, summarized by Notebookcheck, found that wireless charging consumes about 35% more energy than wired for the same charge. An independent test by the Hong Kong Consumer Council measured wireless efficiency from 55% to 81% across 15 chargers, with the worst models wasting nearly half the energy. The calculator uses 75% for wireless, the middle of the Qi range, and 90% for wired.
The efficiency gap shows up directly in charging time. A 5,000 mAh generic phone on a 15W wired charger fills in 2 hours 18 minutes; the same phone on a 15W wireless pad takes 2 hours 46 minutes, about 20% longer, because a quarter of the power never reaches the battery. A 5W wireless pad is the slowest combination the calculator models: 7 hours 42 minutes for a 5,000 mAh battery from empty. Wireless also caps lower than wired on every phone in the calculator: 25W on an iPhone 16 with MagSafe, 15W on a Galaxy S25 or a Pixel 9, against wired caps of 27W, 25W, and 27W. And the rated wattage overstates what the phone draws: GSMArena found the iPhone's MagSafe charger drawing about 18W out of a claimed 25W rating.
| Method | Efficiency | 5,000 mAh, 15W, from 0% | Notes |
|---|---|---|---|
| Wired USB-C | 90 to 95% | 2 hr 18 min | Fastest and most efficient; PPS support matters for Samsung and Pixel |
| Wireless Qi2 / MagSafe | 80 to 85% | 2 hr 46 min at 75% model efficiency | Magnets align the coils; 25W only on iPhone 16 with MagSafe |
| Wireless Qi (older pads) | 70 to 80% | 2 hr 46 min at 75% model efficiency | Misalignment by a few millimetres can cut power sharply |
Measured wireless times confirm the gap. A lab test of the iPhone 16 Pro Max on Apple's 25W MagSafe charger reached 50% in 34 minutes and 80% in 70 minutes, but took 2 hours 23 minutes to fill completely, with the phone nearly full after 1 hour 37 minutes and the rest spent trickling. The same phone on a wired charger finishes in under two hours. The calculator is optimistic on wireless iPhone charging for the same reason it is optimistic on wired iPhone charging: Apple's taper is deeper than the model's 30% figure. Wireless is still the right choice for overnight charging and for a desk pad, where the phone sits for hours anyway; it is the wrong choice when you have 30 minutes before a flight.
Popular phones and their charging limits
The table below gives the four phones in the calculator, with their published battery sizes, their charging caps, and the measured times behind the model. The battery sizes are published figures: Apple does not list milliamp-hours in its own specs, so the iPhone 16 figure of 3,561 mAh comes from regulatory filings and teardowns as reported by GSMArena, while Samsung and Google publish their figures directly.
| Phone | Battery | Wired cap | Wireless cap | Published charging claims |
|---|---|---|---|---|
| Apple iPhone 16 | 3,561 mAh | 27W (model figure) | 25W MagSafe, 15W Qi2 | Up to 50% in around 30 min with a 20W or higher adapter (Apple). 1 hr 42 min full, 59% in 30 min (GSMArena). |
| Samsung Galaxy S25 | 4,000 mAh | 25W | 15W | 56% in 30 min, full in 1 hr 17 min (GSMArena). |
| Samsung Galaxy S25 Ultra | 5,000 mAh | 45W | 15W | 72% in 30 min, 41% in 15 min, full in 59 min (GSMArena). Up to 65% in about 30 min (Samsung). |
| Google Pixel 9 | 4,700 mAh | 27W | 15W Pixel Stand, 12W Qi | Up to 55% in about 30 min with the Google 45W charger (Google). Full in 85 min (GSMArena) or 1 hr 39 min (PhoneArena). |
Three disagreements in the sources are worth stating openly. First, the iPhone 16's wired cap: Apple publishes no figure at all, GSMArena's spec table lists 25W, lab tests measured peaks near 30W with about 27W sustained, Anker lists 27W as the peak for standard models, and one MacRumors report puts standard models near 20W. The calculator uses 27W, the sustained figure, and the true number for the base iPhone 16 sits somewhere in the 20 to 30W range. Second, the Pixel 9's full-charge time: GSMArena measured 85 minutes, while PhoneArena measured 1 hour 39 minutes on a different charger, a 14-minute spread on the same phone. Third, the iPhone 16's MagSafe rating: Apple's tech specs list up to 25W, while an Apple Support article lists a 22.5W peak, and GSMArena measured about 18W of real draw. The calculator uses 25W for the wireless cap and the efficiency gap absorbs the rest.
The pattern across the four phones is that Samsung charges fastest for its wattage, Apple and Google taper hardest, and the headline wattage is a poor guide to the full-charge time. The Galaxy S25 Ultra at 45W fills a 5,000 mAh battery in 59 minutes. The Pixel 9 at 27W takes 85 to 99 minutes for a smaller 4,700 mAh battery. The iPhone 16 at 20W takes 1 hour 42 minutes for a much smaller 3,561 mAh battery. And the Pixel 10 Pro XL, which also charges at 45W, took 82 minutes in GSMArena's test against the S25 Ultra's 59, which shows that two phones on the same wattage can differ by 40% on the same test. The charger is only half the story; the phone's charging curve is the other half.
Common mistakes to avoid
Dividing watt-hours by charger watts. The most common charging-time mistake is the simplest: 18.5 Wh divided by 20W is 0.93 hours, so a 5,000 mAh phone must take 56 minutes on a 20W charger. It does not, because the charger does not deliver 20W to the battery: the average is about 15W below 80% and about 4.5W above it, and the real time is 1 hour 48 minutes, nearly twice the naive figure. Every division-only estimate understates the time by 40 to 70%.
Assuming the charger wattage is what the phone draws. A 65W charger does not push 65W into a phone. The phone negotiates the power it wants and caps at its own limit: 25W on a Galaxy S25, 27W on an iPhone 16 or a Pixel 9, 45W on a Galaxy S25 Ultra. Plugging a Galaxy S25 into a 65W laptop charger charges it at 25W, exactly as a 25W Samsung brick would. The extra wattage is not merely unused; it is never drawn in the first place.
Ignoring the taper when planning a top-up. If you need 20% more battery and you are starting at 60%, the charge runs below 80% and takes about 15 minutes on a 20W charger for a 5,000 mAh phone. If you need the same 20% and you are starting at 80%, the whole top-up runs at the taper rate and takes 49 minutes: the same energy, more than three times as long. The calculator's curve shows this directly, and it is why topping up from 85% to 100% feels so slow.
Using a charger without PPS for a Samsung or Pixel phone. Samsung's Super Fast Charging and Google's Pixel charging both use Programmable Power Supply, which lets the phone fine-tune the voltage as the battery fills. A charger that offers USB-PD fixed voltages but no PPS still charges the phone, but more slowly than the wattage suggests, because the phone cannot request the voltage it wants. Check the charger specs for PPS before buying a fast charger for a Galaxy or Pixel phone.
Judging a charger by the 50% headline. Manufacturers quote the time to 50% because it flatters them: Apple promises up to 50% in around 30 minutes for the iPhone 16, Samsung's S25 Ultra reaches 65% in about 30 minutes, and Google promises 55% in about 30 minutes for the Pixel 9. None of those figures says anything about the time to full, which is where the taper lives. An iPhone 16 reaches 50% in 30 minutes and takes 1 hour 42 minutes to fill: the second half takes more than twice as long as the first.
Charging wirelessly when you are in a hurry. A 15W wireless pad delivers about 75% of its power to the battery, against 90% for a cable, and it caps at 15W on most phones while wired charging goes to 25W or 45W. The result is that a wireless top-up takes roughly twice as long as a wired one on the same phone. Wireless is for overnight and desk charging, where the time does not matter; for a quick top-up before leaving, plug the cable in.
Frequently asked questions
How long does it take to charge a phone from 0 to 100%?
It depends on the battery size and the charger. A 5,000 mAh phone takes about 1 hour 48 minutes on a 20W USB-PD charger and about 6 hours 25 minutes on an old 5W brick, using this calculator's model. Measured times for popular phones: a Galaxy S25 Ultra fills in 59 minutes on a 45W charger, a Galaxy S25 in 77 minutes on a 25W charger, an iPhone 16 in 1 hour 42 minutes on a 20W charger, and a Pixel 9 in 85 to 99 minutes on a 30W charger, all from GSMArena or PhoneArena tests. The last 20% takes nearly half the total time on every phone, because charging slows sharply above 80%.
Why does my phone charge slowly after 80%?
Because lithium-ion batteries charge in two stages, constant current then constant voltage, and the switch lands around 70 to 80%. Below 80% the charger pushes a steady high current; above 80% the battery has reached its maximum safe voltage of about 4.2V per cell, so the charger holds the voltage and lets the current fall as the battery fills. In published tests the average power above 80% runs from about 25% to 32% of the fast-phase average, which is why the last 20% takes nearly half the total charge time. The slowdown protects the battery: a high voltage stresses lithium-ion cells, which is why Apple and Samsung both offer an 80% charge limit in settings.
Does a higher wattage charger always charge faster?
No. A phone never draws more than its own limit, so a charger above that limit charges no faster than one at it. A Galaxy S25 caps at 25W, so a 65W charger charges it at 25W, exactly like a 25W brick. An iPhone 16 caps at about 27W and a Pixel 9 at 27W, while a Galaxy S25 Ultra can use the full 45W. Even below the cap, the gains shrink: on a 5,000 mAh phone, going from 5W to 20W saves about 4 hours 37 minutes, but going from 20W to 30W saves only 30 minutes, because the phone's charging curve and the taper limit what extra wattage can do.
Is wireless charging slower than wired charging?
Yes, for two reasons. First, wireless charging is less efficient: a Qi pad delivers 70 to 80% of its power to the battery and a Qi2 pad 80 to 85%, against 90 to 95% for a wired USB-C charger, with the rest lost as heat. Second, wireless caps lower: 25W on an iPhone 16 with MagSafe and 15W on a Galaxy S25 or a Pixel 9, against wired caps of 27W, 25W, and 27W. A 5,000 mAh phone on a 15W wireless pad takes about 2 hours 46 minutes from empty, against 2 hours 18 minutes on a 15W cable. Wireless is best for overnight and desk charging, where the extra time does not matter.
How long does it take to charge an iPhone 16?
Apple promises up to 50% in around 30 minutes with a 20W or higher USB-C adapter, and publishes no full-charge time and no maximum wired wattage. GSMArena measured 59% in 30 minutes, 85% in one hour, and a full charge in 1 hour 42 minutes on a 45W PD charger. This calculator estimates 42 minutes to 80% and 1 hour 17 minutes to full on a 20W charger, which is 25% optimistic against GSMArena's measurement, because the iPhone taper is deeper than the model's central figure. On a 30W charger the calculator estimates 33 minutes to 80% and 1 hour to full. On a 25W MagSafe pad, a lab test of the larger iPhone 16 Pro Max took 2 hours 23 minutes to fill.
Does fast charging damage the battery?
Fast charging adds heat and voltage stress, which age a lithium-ion battery faster than slow charging, but the effect is modest on modern phones and the phone's own charging management limits it. Battery University notes that charging at 0.8C or less prolongs battery life, that a high voltage stresses the battery, and that it is better not to fully charge, which is why Apple and Samsung offer 80% charge limits. The practical steps are simple: avoid charging in heat, avoid leaving the phone at 100% for hours, and use the 80% limit for overnight charging. The charger wattage matters less than heat and voltage, because the phone, not the charger, decides the current.
What charger do I need for USB-PD fast charging?
Any USB-C charger rated 20W or higher with USB Power Delivery gives a phone its standard fast charge: a 20W charger offers 5V at up to 3A and 9V at up to 2.22A, and the phone negotiates the tier it wants. For a Samsung Galaxy or a Google Pixel, the charger should also support Programmable Power Supply (PPS), which lets the phone fine-tune the voltage between 3.3V and 21V; without PPS a Samsung phone charges more slowly than its wattage suggests. The cable matters above 60W, where a 5A cable with an electronic marker chip is required, but at phone wattages a standard USB-C cable is fine. A charger above your phone's cap wastes money: a Galaxy S25 needs 25W, an iPhone 16 or Pixel 9 needs about 27W, and only the Galaxy S25 Ultra benefits from 45W.
Sources
Every figure on this page comes from one of the sources below, each accessed 20 November 2026. Where sources disagree, the page shows the range and says so instead of picking a false single number.
- gsmarena.com — iPhone 16 specifications: 3,561 mAh battery, PD2.0 wired charging, 50% in 30 minutes, 25W wireless MagSafe and Qi2. Accessed 20 November 2026.
- gsmarena.com — iPhone 16 review, lab tests: 3,561 mAh battery, 33% in 15 minutes, 59% in 30 minutes, 85% in one hour, last 15% about 42 minutes, full in 1 hour 42 minutes on a 45W PD charger. Accessed 20 November 2026.
- gsmarena.com — iPhone 16e vs iPhone 16 charging comparison: north of 30% in 15 minutes, close to 60% in 30 minutes, about 85% in one hour. Its summary says a full charge after about 90 minutes, but GSMArena's dedicated iPhone 16 review measured 1 hour 42 minutes, so the review figure is the one used. Accessed 20 November 2026.
- gsmarena.com — iPhone 16 Plus review, lab tests: 4,674 mAh battery, maximum draw around 30W, 27% in 15 minutes, 55% in 30 minutes, 85% in one hour, last 15% about 40 minutes, full in 1 hour 39 minutes on a 45W PD charger. Accessed 20 November 2026.
- gsmarena.com — Galaxy S25 Ultra review, lab tests: 5,000 mAh battery, 45W charging, 41% in 15 minutes, 72% in 30 minutes, full in 59 minutes on Samsung's 45W adapter, peak draw 42W, 39W peak on the bundled 3A cable. Accessed 20 November 2026.
- gsmarena.com — Galaxy S25 Plus review, lab tests: 4,900 mAh battery, 45W charging, 42% in 15 minutes, 75% in 30 minutes, full in 58 minutes. Accessed 20 November 2026.
- gsmarena.com — Galaxy S25 vs Galaxy S24 charging comparison: 25W wired charging replenishes the 4,000 mAh battery in around 1 hour 15 minutes. Accessed 20 November 2026.
- gsmarena.com — Galaxy S25 Ultra vs iPhone 16 Pro Max: S25 Ultra full in about an hour, iPhone 16 Pro Max in about two hours; MagSafe draws about 18W out of a claimed 25W rating. Accessed 20 November 2026.
- gsmarena.com — Pixel 9 review, lab tests: 4,700 mAh battery, 52% in 30 minutes and full in 1 hour 28 minutes on the 30W charger, 55% in 30 minutes on a 45W charger, full in 85 minutes in GSMArena comparison tests. Accessed 20 November 2026.
- phonearena.com — Pixel 9 battery and charging tests: 4,700 mAh battery, 27W wired, 55% in 30 minutes, full charge 1 hour 39 minutes for the Pixel 9 and 1 hour 21 minutes for the Pixel 9 Pro. Accessed 20 November 2026.
- androidpolice.com — Pixel 9 faster wired charging: 27W maximum wired draw, 4,700 mAh battery, 37W on the Pixel 9 Pro XL. Accessed 20 November 2026.
- batteryuniversity.com — BU-409 Charging Lithium-ion: constant current then constant voltage stages, stage 1 fills the battery to about 70%, higher current lengthens the saturation stage, full charge when current drops to 3% of rated current, advised charge rate 0.5C to 1C, better not to fully charge. Accessed 20 November 2026.
- battery.mba — Lithium-ion charging voltages and stages: constant current to about 80%, constant voltage taper to full, typical 1C charge about 60 minutes of constant current plus about 30 minutes of taper, NMC nominal voltage 3.7V, full voltage 4.20V. Accessed 20 November 2026.
- chargetechlab.com — Wireless charging vs wired: Qi wireless 70 to 80% efficient, Qi2 80 to 85%, wired GaN 90 to 95%. Accessed 20 November 2026.
- notebookcheck.net — Qi charging losses, citing the International Energy Agency: wireless charging consumes about 35% more energy, wired charging 90 to 95% efficient, Qi 60 to 80%. Accessed 20 November 2026.
- androxus.com — Fast charging standards: USB-PD fixed voltage tiers 5V, 9V, 15V, 20V up to 100W, PD 3.1 Extended Power Range to 240W, PPS adjustable 3.3V to 21V in 20mV steps, 5A cable required above 60W. Accessed 20 November 2026.
- eronix.in — USB Power Delivery and iPhone: a 20W charger offers 5V at up to 3A (15W) and 9V at up to 2.22A (20W); chargers above 15W must offer 5V and 9V, above 27W must add 15V, above 45W must add 20V. Accessed 20 November 2026.
- blog.frekvens.ai — iPhone 16 charging speed: Apple promises up to 50% in around 30 minutes with a 20W or higher adapter for all four models, publishes no maximum wired wattage and no 0 to 100% time, and its own pages disagree on MagSafe (25W in tech specs, 22.5W peak in Apple Support). Accessed 20 November 2026.
- aivanet.com — iPhone 16 fast charging requirements, from MacRumors: charging maxes out at 30W per ChargerLAB testing, standard models near 20W, 25W MagSafe needs a 30W or higher adapter. Accessed 20 November 2026.
- wandkey.com — 25W Apple MagSafe charger test: iPhone 16 Pro Max reached 50% in 34 minutes, 80% in 1 hour 10 minutes, and full in about 2 hours 23 minutes on MagSafe. Accessed 20 November 2026.
- redwaybattery.com — How many hours to charge a 5000 mAh battery: standard USB-A 5W takes about 6 hours, USB-C PD 18W about 1.5 to 2 hours, 5000 mAh at 3.7V is 18.5 Wh. Accessed 20 November 2026.
- techsith.com — How many hours to charge a 5000 mAh power bank: 5W takes 4 to 6 hours, 10W takes 2 to 3.5 hours, 18 to 20W takes about 1.5 to 2.5 hours; Xiaomi 5000 mAh models take 3.5 hours on 5V/2A and about 1.75 hours on 20W. Accessed 20 November 2026.