Skip to content

Tide Height Calculator

Pick rising when the first tide in your table is the low water, falling when it is the high water.

All heights, depths, and drafts use this unit. US tide tables use feet; UK tables use meters.

Low water height on a rising tide, high water height on a falling tide. Negative when the low water falls below chart datum.

High water height on a rising tide, low water height on a falling tide. From the same tide table as the first height.

Decimal hours: 6.25 means 6 hours 15 minutes. About 6 hours 12 minutes on most coasts. Between 0.5 and 12.

How far into the tide you want the height: 0 at the first tide, the full time between tides at the second.

Under-keel clearance (optional)

Depth printed on the chart at the spot you care about. Leave blank to skip clearance.

How deep your boat sits below the waterline. Leave blank to skip clearance.

Extra water you want under the keel, beyond the draft. 0 means no margin.

Height of tide

Height at each sixth of the tide

How the numbers were worked out

      This tool estimates the height of tide between high and low water from the numbers you enter, for planning and education only. It is not navigation data. Official NOAA predictions govern, and you should never navigate on this alone. The rule of twelfths is an approximation that assumes a regular semidiurnal tide; wind, weather, and local geography move real water away from the predicted curve. Check the official prediction and the port's own tidal curve before committing the boat.
      The tide rises or falls by 1, 2, 3, 3, 2, and 1 twelfths of the range in the six equal parts of the time between high and low water. Boston on October 23, 2026: low water 0.92 ft at 3:21 AM, high water 9.63 ft at 9:36 AM, a range of 8.71 ft. At 7:00 AM, 3.65 hours after low water, 7.50 twelfths have moved, so the tide is 6.36 ft. Enter your two tides above for the height at any time, a sine-curve cross-check, and under-keel clearance.

      Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.

      How to use the Tide Height Calculator

      A tide table tells you the times and heights of high water and low water, and nothing in between. But the water you care about is almost always the water in between: the depth over a bar at 10 in the morning, the water under your keel when you leave a drying berth at noon, the level on the beach when the kids go swimming at 3 in the afternoon. This calculator fills in the gap. Give it the two tides on either side of the time you care about, and it works out the height of tide at that time using the rule of twelfths, the method taught in RYA navigation courses and described in Bowditch, The American Practical Navigator. It also checks the answer against the sine curve that the US tide tables use for the same job, and, if you enter a charted depth and a draft, it works out the clearance under your keel and the earliest time with enough water.

      To get your result, follow these steps:

      1. Pick the tide direction. Choose rising when the first tide in your table is the low water and the tide is coming in, falling when the first tide is the high water and the tide is going out. The direction sets which height is the starting point and which way the numbers move.
      2. Pick the unit. Feet or meters. Every height, depth, and draft on the page uses this unit. US tide tables use feet, and heights are measured above MLLW, mean lower low water. UK tables use meters above chart datum. Mixing units is the most common mistake in tidal arithmetic: if your table is in feet and your charted depth is in meters, convert one of them first with our Unit Converter.
      3. Enter the height at the first tide. On a rising tide this is the low water height; on a falling tide it is the high water height. Copy it from your tide table exactly as printed. A low water below chart datum is negative: enter it with the minus sign, because a low water of -0.50 ft makes the range larger, not smaller.
      4. Enter the height at the second tide. On a rising tide this is the high water height; on a falling tide it is the low water height. It must be above the first height on a rising tide and below it on a falling tide, or the calculator will tell you the two are swapped.
      5. Enter the time between the two tides, in decimal hours. Subtract the first tide time from the second. A rise from 3:21 AM to 9:36 AM is 6 hours 15 minutes, which is 6.25 hours. On most coasts the time between high and low water is about 6 hours 12 minutes, because the tidal day, the time between one high water and the next, is about 12 hours 25 minutes. The calculator accepts 0.5 to 12 hours, and warns you when the time falls outside 5 to 7 hours, where the rule of twelfths is at its least reliable.
      6. Enter the time since the first tide, in decimal hours. This is how far into the tide you want the height. A time of 3.65 hours means 3 hours 39 minutes after the first tide. Enter 0 for the height at the first tide itself, and the full time between tides for the height at the second tide. The calculator refuses a time longer than the time between the tides, because the rule only works between two tides you have in the table.
      7. Enter the clearance details, if you want them. Charted depth is the depth printed on the chart at the spot you care about. Draft is how deep your boat sits below the waterline. Safety margin is the extra water you want under the keel beyond the draft. Enter charted depth and draft together, or leave both blank to skip clearance. With them, the calculator shows the water depth, the clearance under the keel, and the earliest time with enough water on a rising tide, or the latest time on a falling tide.

      The tool updates as you type, so you can try different times quickly: slide the time since the first tide forward and watch the height climb, or change the draft and watch the earliest safe time move. Try the example buttons under the form. The first is the default: Boston on October 23, 2026, low water 0.92 ft at 3:21 AM and high water 9.63 ft at 9:36 AM, checked against the NOAA prediction for station 8443970, with the height worked out 3.65 hours into the tide. The second is a falling tide over a bar with a 5 ft draft. The third is a metric drying berth. The fourth is a short 4.5 hour tide, where the calculator warns you the rule is less reliable.

      Read the full result, not just the headline. The headline gives the height at your time and, in clearance mode, the water under your keel. The cards show the rule height, the sine-curve height, the tidal range, and the rate the tide is rising or falling. The table shows the height at each sixth of the tide, so you can see the whole curve at a glance. The guidance explains the result in plain language, the warnings flag the cases that need a second look, and the steps print the full working so you can check every figure against your own arithmetic.

      This is a planning estimate only. Official NOAA predictions govern, and you should never navigate on this alone. The rule of twelfths is an approximation of a smooth curve, and real water has wind, weather, and local geography in it. Use the calculator to plan, then check the official prediction and the port's own tidal curve before you commit the boat.

      How it works

      The calculator runs four calculations in order: the range and the rule of twelfths height, the sine-curve cross-check, the rate of rise or fall, and, when you enter clearance details, the water depth, the clearance, and the earliest or latest time with enough water. Each step uses the result of the one before it, and the steps section on the page prints all of them so you can check the arithmetic.

      Step 1: the range and the rule of twelfths

      The range of tide is the difference in height between the high water and the low water on either side of your time. Bowditch defines it exactly that way: high water minus low water. In the Boston default, high water 9.63 ft minus low water 0.92 ft gives a range of 8.71 ft. When the low water is below chart datum its height is negative, and the range is larger than the high water alone: a high water of 4.00 ft and a low water of -0.50 ft make a range of 4.50 ft.

      The rule of twelfths divides the range into twelve equal parts, called twelfths, and divides the time between the tides into six equal parts, called sixths. In the first sixth the tide moves 1 twelfth of the range, in the second 2 twelfths, in the third 3, in the fourth 3, in the fifth 2, and in the sixth 1. The sequence 1, 2, 3, 3, 2, 1 adds up to 12, the full range. The tide starts slowly, runs fastest in the middle, and slows again near the turn, which is why half the whole range, 6 twelfths, moves in the middle two sixths alone.

      Within each sixth the calculator lets the water move at a steady rate, so a time partway through a sixth gets a part share of that sixth's twelfths. In the Boston default, the time between tides is 6.25 hours, so one sixth lasts 6.25 divided by 6, which is 1.0417 hours. The time you want, 3.65 hours after low water, is 3.65 divided by 1.0417, which is 3.50 sixths. The twelfths moved by then are the 6 twelfths of the first three sixths plus half of the fourth sixth's 3, which is 7.50 twelfths. The height is the low water height plus 7.50 twelfths of the range: 0.92 plus 7.50 divided by 12 times 8.71, which is 0.92 plus 5.44, giving 6.36 ft. A falling tide works the same way in reverse: count the sixths after high water and subtract the twelfths from the high water height.

      Step 2: the sine-curve cross-check

      The rule of twelfths is an approximation of a sine curve. The US tide tables use the curve itself: Table 3 of the tide tables, as Bowditch describes it, finds the approximate height of tide at any time between high and low water by assuming the height follows a sine curve, and warns that actual values may vary. The calculator works the curve out directly. The fraction of the range that has moved at time t, out of a total time D between the tides, is (1 minus cos(180 degrees times t divided by D)) divided by 2. The height is the first height plus that fraction times the signed range.

      In the Boston default, t is 3.65 hours and D is 6.25 hours, so the fraction is (1 minus cos(105.12 degrees)) divided by 2, which is 0.6304. The sine height is 0.92 plus 0.6304 times 8.71, which is 0.92 plus 5.49, giving 6.41 ft. The rule gives 6.36 ft and the curve gives 6.41 ft, a difference of 0.05 ft. The two methods agree exactly at two, three, and four sixths, where the rule's fractions of 0.250, 0.500, and 0.750 match the curve's, and differ most near 0.62 sixths and 5.38 sixths, where the gap reaches 0.0256 of the range. On an 8.71 ft range that widest gap is 0.22 ft. When the gap at your time is over 2 percent of the range, the calculator warns you and tells you to use the lower figure for clearance.

      Step 3: the rate of rise or fall

      The rate matters as much as the height. A boat that grounds at the top of the tide floats off gently; a boat that grounds at mid-tide can be left high and dry by water falling three times as fast. The calculator reports the rate from the rule: the twelfths moving in the current sixth, times one twelfth of the range, divided by the length of a sixth. In the Boston default, the fourth sixth moves 3 twelfths, one twelfth is 0.73 ft, and a sixth lasts 1.0417 hours, so the rate is 3 times 0.73 divided by 1.0417, which is 2.10 ft an hour. The sine rate at the same moment is 2.11 ft an hour, from the curve's slope. On a 12 ft range over 6 hours the contrast is stark: the tide rises 1.00 ft an hour in the first sixth and 3.00 ft an hour in the middle sixths, three times as fast. The first and last sixths are the slack water of the turn; the middle two sixths carry half the whole tide.

      Step 4: clearance and the earliest time with enough water

      Clearance is the question that matters most to a skipper: will there be enough water under the keel? The depth of water is the charted depth plus the height of tide, the rule every navigation course teaches. Take away the draft and the safety margin, and what is left is the clearance. In the metric example, a charted depth of 1.20 m plus a tide height of 2.51 m gives 3.71 m of water. Take away a draft of 1.80 m and a safety margin of 0.50 m, and 1.41 m stays under the keel. If the answer is negative, the calculator says so plainly: short of the water needed, or aground if the water is shallower than the draft itself.

      The inverse question is just as useful: when is the earliest time with enough water? The tide height needed is the draft plus the safety margin minus the charted depth. In the metric example that is 1.80 plus 0.50 minus 1.20, which is 1.10 m of tide. The calculator works out when the tide reaches that height by the rule and by the sine curve: 1 hour 2 minutes after low water by the rule, 1 hour 10 minutes by the sine curve. On a falling tide the same calculation gives the latest time with enough water, the moment to be back across the bar. The times round in the safe direction, to whole minutes: the earliest time rounds up, so you never arrive before there is enough water, and the latest time rounds down, so you never stay past the moment the water runs out. The calculator also checks the height at the returned time against its own arithmetic, so the time it prints always delivers the water it promises.

      Worked example 1: Boston, rising tide

      NOAA station 8443970, Boston, October 23, 2026: low water 0.92 ft at 3:21 AM, high water 9.63 ft at 9:36 AM. The height at 7:00 AM, 3.65 hours after low water.

      • Range: 9.63 minus 0.92 = 8.71 ft
      • One twelfth: 8.71 divided by 12 = 0.73 ft
      • One sixth of the tide: 6.25 h divided by 6 = 1.0417 h
      • Time since low water: 3.65 h = 3.50 sixths
      • Twelfths moved: 7.50 of 12
      • Height by the rule: 0.92 plus 7.50/12 times 8.71 = 6.36 ft
      • Sine cross-check: 0.92 plus 0.6304 times 8.71 = 6.41 ft
      • Rate: 3 times 0.73 divided by 1.0417 = 2.10 ft an hour

      Worked example 2: a bar crossing on a falling tide

      The same Boston tide, falling: high water 9.63 ft, low water 0.92 ft, 6.25 hours between them. Two hours after high water, over a bar with a charted depth of 3.00 ft, in a boat drawing 5.00 ft with a 1.00 ft safety margin.

      • Range: 9.63 minus 0.92 = 8.71 ft
      • One sixth of the tide: 6.25 h divided by 6 = 1.0417 h
      • Time since high water: 2.00 h = 1.92 sixths
      • Twelfths moved: 2.84 of 12
      • Height by the rule: 9.63 minus 2.84/12 times 8.71 = 7.57 ft
      • Water depth: 3.00 plus 7.57 = 10.57 ft
      • Clearance: 10.57 minus 5.00 minus 1.00 = 4.57 ft
      • Water needed: 5.00 plus 1.00 minus 3.00 = 3.00 ft of tide
      • Latest time with enough water: 4 h 14 min after high water by the rule, 4 h 13 min by the sine curve

      Worked example 3: a drying berth in meters

      Low water 0.80 m, high water 4.40 m, 6.20 hours between them. Three hours after low water, with a charted depth of 1.20 m, a draft of 1.80 m, and a 0.50 m safety margin.

      • Range: 4.40 minus 0.80 = 3.60 m
      • One twelfth: 3.60 divided by 12 = 0.30 m
      • One sixth of the tide: 6.20 h divided by 6 = 1.0333 h
      • Time since low water: 3.00 h = 2.90 sixths
      • Twelfths moved: 5.70 of 12
      • Height by the rule: 0.80 plus 5.70/12 times 3.60 = 2.51 m
      • Sine cross-check: 0.80 plus 0.4747 times 3.60 = 2.51 m
      • Water depth: 1.20 plus 2.51 = 3.71 m
      • Clearance: 3.71 minus 1.80 minus 0.50 = 1.41 m
      • Water needed: 1.80 plus 0.50 minus 1.20 = 1.10 m of tide
      • Earliest time with enough water: 1 h 2 min after low water by the rule, 1 h 10 min by the sine curve

      Worked example 4: checking against the US tide tables

      The boats.com tide pages work a Table 3 example from the National Ocean Service: morning low water 0.10 ft at 5:22 AM, morning high water 4.20 ft at 11:14 AM, a duration of rise of 5 hours 52 minutes. Table 3 gives 1.7 ft at 7:55 AM. The calculator, given the same endpoints and a time 2.55 hours after low water, gives 1.75 ft by the rule of twelfths and 1.73 ft by the sine curve. All three methods land within 0.05 ft of each other, which is the honest precision of tidal estimation between table entries: the rule, the curve, and the printed table are three ways of drawing the same smooth rise, and they agree to within a couple of inches on a 4.10 ft range.

      The rule of twelfths against the sine curve

      The table below compares the two methods at the end of each sixth, as fractions of the range. The rule is a staircase that touches the curve at two, three, and four sixths and sits slightly above it at one sixth and slightly below it at five sixths. The largest gap between them is 0.0167 of the range at the sixth boundaries, and 0.0256 of the range inside the first and last sixths, near 0.62 and 5.38 sixths. On a 10 ft range the widest gap is about a quarter of a foot. On a 40 ft range, the sort of tide the Bay of Fundy sees, it is about a foot, which is why the calculator warns you when the gap at your time passes 2 percent of the range.

      Sixths goneTwelfths movedRule fraction of rangeSine fraction of rangeDifference
      11 of 120.0830.0670.016
      23 of 120.2500.2500.000
      36 of 120.5000.5000.000
      49 of 120.7500.7500.000
      511 of 120.9170.9330.016
      612 of 121.0001.0000.000

      The table also shows why the rule is so easy to use in your head. After one sixth, about a twelfth of the range has moved. After two, a quarter. After three, half. After four, three quarters. After five, eleven twelfths. The sine curve passes through the same quarter, half, and three-quarter marks at the same times, which is why the rule feels right: it is the curve with the corners left in. The corners only show near the turns, where the curve flattens and the rule keeps stepping.

      A second table shows the same idea in feet, for a 12 ft range over 6 hours, the textbook example. Read down the heights and you can see the shape of the tide: slow, then fast, then slow again.

      Hours after low waterTwelfths movedRise in that hourHeight of tide
      00 of 12Low water0.00 ft
      11 of 121.00 ft1.00 ft
      23 of 122.00 ft3.00 ft
      36 of 123.00 ft6.00 ft
      49 of 123.00 ft9.00 ft
      511 of 122.00 ft11.00 ft
      612 of 121.00 ft12.00 ft

      Features

      Rule of twelfths height. The headline answer: the height of tide at your time, worked out from the two tide-table endpoints by the 1, 2, 3, 3, 2, 1 sequence, with part-sixth times handled by steady movement inside each sixth. Rising and falling tides both work, and negative low water heights below chart datum are handled correctly.

      Sine-curve cross-check. Every answer is checked against the sine curve behind Table 3 of the US tide tables. The two figures sit side by side in the result cards, and the guidance names the difference between them. When the gap passes 2 percent of the range, the calculator warns you and tells you to use the lower figure for clearance.

      Rate of rise or fall. The result shows how fast the water is moving at your time, in feet or meters an hour, by the rule and by the curve. The mid-tide rate is three times the rate near the turns, which is the number that decides whether a grounding is an inconvenience or a long wait.

      Hour-by-hour table. The result prints the height at each sixth of the tide, from the first tide to the second, so you can read the whole curve without running the calculator seven times. The table also shows how long one sixth lasts on your tide, which is rarely exactly an hour.

      Under-keel clearance mode. Enter the charted depth and your draft, plus a safety margin, and the calculator works out the water depth and the clearance under the keel at your time. It tells you plainly when you are short of water, and when the keel would be aground. It also checks the sine curve's clearance against the rule's, and warns you when the curve gives less water.

      Earliest and latest time with enough water. The inverse calculation: the earliest time with enough water on a rising tide, or the latest time on a falling tide, by the rule and by the sine curve. Times round in the safe direction to whole minutes, and the calculator verifies the height at the returned time against its own arithmetic, so the time it prints always delivers the water it promises.

      Warnings that mean something. The calculator warns when the time between tides falls outside the 5 to 7 hours the rule assumes, when the two methods disagree by more than usual, when the sine curve gives less clearance than the rule, when clearance is exactly zero or under half a unit, and when you are short of water. Each warning names the figures behind it.

      Full working, printed. Every result shows its steps: range, one twelfth, one sixth, sixths gone, twelfths moved, the height by the rule, the sine cross-check, and, in clearance mode, the water depth, the clearance, and the water needed. You can check every number with a pocket calculator.

      Use cases

      Crossing a bar. The classic use. A bar has a charted depth, your boat has a draft, and the tide decides whether you cross. Enter the two tides, the charted depth, the draft, and a margin, and the calculator gives the clearance at your planned time and the earliest time with enough water. On the way back, run it as a falling tide for the latest time you can return. The Boston bar example above shows the shape of the answer: 4.57 ft of clearance two hours after high water, and a latest return 4 hours 14 minutes after high water.

      Leaving a drying berth. Berths that dry at low water need the tide to float the boat before you can leave, and need it again when you come back. The earliest-time calculation tells you when you can leave in the morning; the falling-tide version tells you when you must be back. The metric example above, a 1.80 m draft over 1.20 m of charted depth, floats 1 hour 2 minutes after low water.

      Beaching and careening. If you plan to beach a boat for scrubbing or repairs, you want to know the height at the time you ground and the height when you expect to float again. Run the calculator for both times on the same tide, and the difference between the two heights is the water you lose or gain. The rate figure tells you how fast the water will leave you once you touch.

      Kayaking and beachgoing. Kayakers launching across tidal flats and beachgoers walking out to sandbars need the height between tides as much as sailors do. The rule works the same way at any scale: a beach with a 6 ft range rises 3 ft in the middle two hours, which is the difference between a dry walk back and a swim. Our Kayak Size Finder matches a kayak to your size, and our Paddle Board Size Finder does the same for paddle boards.

      Anchoring. The depth at anchor changes with the tide, and the scope you need changes with it. Work out the height at high water to find the deepest water you will swing in, and at low water to find the shallowest. Our Anchor Size and Rode Calculator sizes ground tackle for the depth you will anchor in, and the tide height at high water is the depth to size for.

      RYA and ASA students. The rule of twelfths is on the syllabus for Day Skipper and Coastal Skipper courses, and for ASA 101 and 103, and it is examined by hand. This calculator is a way to check your hand-worked answers: run the same numbers through the tool and compare the height, the twelfths count, and the steps. The steps section shows the working in the same order a navigation exercise expects.

      Passage planning. A passage with a tidal gate, a bridge with limited air draft, or a shallow channel needs the height at the time you will be there, not at high water. Run the calculator for the arrival time, then for an hour either side, and you have the window. Pair it with our Boat Fuel Cost and Range Calculator for the fuel and range side of the plan, and our Sailboat Hull Speed Calculator for the speed side.

      When the rule does not work

      The rule of twelfths is an approximation with known limits, and knowing them is part of using it well. It assumes a regular semidiurnal tide: two high waters and two low waters a day, about six hours apart, with the rise and fall following a smooth, symmetrical curve. Where that assumption holds, the rule is good to a few percent of the range. Where it does not, the rule can be badly wrong, and no calculator can fix that from two endpoints alone.

      Double high waters. The Solent, on the south coast of England, is the famous case: the tide there has a double high water, with a long stand and a second peak, and the rule of twelfths does not describe the curve at all. Poole Harbour has a double high water too, and Weymouth Bay has a double low water. In these places use the port's own tidal curve, printed in the almanac, or the official predictions.

      Shallow estuaries. In a shallow estuary the flood can run much faster than the ebb: the tide rushes in over a few hours and drains away slowly. The rule assumes the rise and the fall take the same shape, so it overstates the height early in a fast flood and understates it late in a slow ebb. The calculator warns when the time between tides falls outside 5 to 7 hours, which catches the worst of these cases, but a 6-hour tide in a shallow estuary can still be lopsided.

      Diurnal tides. Parts of the US Gulf Coast, eastern Mexico, and some Caribbean islands have diurnal tides: one high water and one low water a day, with a rise and fall of about 12 hours rather than 6. The rule's six-hour shape does not apply. Mixed tides, with unequal high waters and unequal low waters, are also outside the rule's assumptions, though the rule is often used as a rough guide for them anyway. BoatUS Magazine makes the same point: the rule is a guide for semi-diurnal tides, and the Gulf Coast's diurnal tides need a different approach.

      Weather. Wind and air pressure move real water away from the predicted curve. A strong onshore wind piles water up against the coast; a strong offshore wind blows it away. A deep low-pressure system raises the sea level, and a high-pressure system depresses it. BoatUS notes that high winds and storm surges change the result, and the tide table knows nothing about any of it. The rule gives the astronomical tide. The water you actually float in is the astronomical tide plus the weather, and the weather term can be a foot or more in a blow.

      Secondary ports. Tide tables give full predictions for standard ports and time and height differences for secondary ports nearby. The differences shift the times and heights of the endpoints, and you must apply them before running the rule, not after. A secondary port correction of 40 minutes on the time and 0.5 ft on the height changes the answer by more than the difference between the rule and the sine curve.

      Datum and time zone errors. Two mistakes that have nothing to do with the rule and everything to do with the inputs: using heights from a table on one datum with a chart on another, and forgetting daylight saving time. US tables use MLLW; UK charts use chart datum; the two are close but not the same, and the difference matters in shallow water. And a tide table printed in local time against a plan made in UTC is an hour wrong, which at mid-tide is a quarter of the range. Check the datum and the time zone before you trust the answer. Our Time Zone Converter helps when the table and the plan use different zones.

      Sources

      The rule of twelfths is described in Bowditch, The American Practical Navigator (NGA Pub. 9), which also describes Table 3 of the US tide tables, the sine-curve method this calculator uses as its cross-check, and defines the range of tide as the difference in height between a high water and the low water before or after it. Bowditch puts low water about a quarter of a tidal day, roughly 6 hours 12 minutes, before and after high water, and notes that the interval varies from day to day.

      RYA navigation handbooks teach the rule as the standard method for finding the height of tide between high and low water, with the 1, 2, 3, 3, 2, 1 sequence and the warning that it assumes a roughly six-hour rise or fall on a symmetrical curve. Mel Neale's article in BoatUS Magazine, October 2016, revised October 2022, calls the rule an easy guide for semi-diurnal tides, the kind with two nearly identical tidal cycles a day that take about six hours to rise or fall, and notes that high winds and storm surges change the result. The BoatUS guide to tide tables carries the same sequence. The boats.com tide pages print the rule with the worked Table 3 example used in this page's fourth worked example, and warn that all of the methods assume the rise and fall conform to simple cosine curves, so the heights obtained are approximate.

      Official tide predictions for US waters come from NOAA Tides and Currents, which offers predictions for more than 3,000 stations, up to two years in the past or future. The Boston example on this page was checked against the NOAA prediction for station 8443970 for October 23, 2026: low water 0.92 ft at 3:21 AM, high water 9.63 ft at 9:36 AM. The sine-curve fractions in the comparison table, and the widest gap of 0.0256 of the range near 0.62 sixths, are computed from the cosine formula, not quoted: at one sixth the curve gives (1 minus cos 30 degrees) divided by 2, which is 0.067, and at five sixths it gives (1 minus cos 150 degrees) divided by 2, which is 0.933.

      One terminology note: a few boating pages call two tides a day diurnal. That is wrong. Two high waters and two low waters a day is semidiurnal; one of each a day is diurnal. This page follows Bowditch and NOAA usage throughout.

      External sources: NOAA Tide Predictions user guide, NOAA: Where can I get tide predictions?, Boats.com: Tide and Currents, BoatUS: The Boater's Guide to Tide Tables. All sources re-verified November 20, 2026.

      Frequently asked questions

      What is the rule of twelfths?

      The rule of twelfths estimates the height of the tide between high and low water. Divide the range of tide, the difference between the high water and low water heights, into twelve equal parts, and divide the time between the two tides into six equal parts. In the first sixth the tide moves 1 twelfth of the range, in the second 2 twelfths, in the third 3, in the fourth 3, in the fifth 2, and in the sixth 1. The sequence 1, 2, 3, 3, 2, 1 adds up to the full range. After three sixths, half the range has moved. The rule is taught in RYA navigation courses and described in Bowditch, and it assumes a regular semidiurnal tide with about six hours between high and low water.

      How accurate is the rule of twelfths?

      On a regular semidiurnal tide the rule agrees with the sine curve behind the US tide tables to within 0.0256 of the range at its worst point, near 0.62 sixths into the tide, and exactly at two, three, and four sixths. On an 8.71 ft range the widest gap is 0.22 ft. Against the National Ocean Service Table 3 method, the rule lands within 0.05 ft on a 4.10 ft range in the worked example on this page. The rule is least reliable where the tide is irregular: double high waters as in the Solent, shallow estuaries where the flood runs faster than the ebb, diurnal tides with one cycle a day, and any day with strong wind or a storm surge, which moves real water away from the predicted curve.

      How do I work out the height of tide at a time between high and low water?

      Take the two tides on either side of your time from a tide table. Subtract to get the range, divide the range by 12 to get one twelfth, and divide the time between the tides by 6 to get one sixth. Work out how many sixths have passed since the first tide, count the twelfths that have moved by the 1, 2, 3, 3, 2, 1 sequence, and add or subtract them from the first height. Boston on October 23, 2026: low water 0.92 ft at 3:21 AM, high water 9.63 ft at 9:36 AM, a range of 8.71 ft and a sixth of 1.0417 hours. At 7:00 AM, 3.65 hours after low water, 3.50 sixths have passed and 7.50 twelfths have moved, so the height is 0.92 plus 7.50 divided by 12 times 8.71, which is 6.36 ft. This calculator does the same arithmetic and checks it against the sine curve.

      What is the sine-curve cross-check?

      The sine curve is the smooth curve the rule of twelfths approximates, and it is the curve behind Table 3 of the US tide tables. The fraction of the range that has moved at time t out of a total time D between the tides is (1 minus cos(180 degrees times t divided by D)) divided by 2. In the Boston example the fraction at 3.65 hours into a 6.25 hour tide is 0.6304, giving a height of 6.41 ft against the rule's 6.36 ft. The two agree exactly at two, three, and four sixths. The calculator shows both figures and warns you when they disagree by more than 2 percent of the range, in which case you should use the lower figure for clearance.

      How do I work out clearance under the keel?

      Add the height of tide to the charted depth to get the depth of water, then subtract your draft and your safety margin. What is left is the clearance under the keel. In the metric example on this page, a charted depth of 1.20 m plus a tide height of 2.51 m gives 3.71 m of water; take away a draft of 1.80 m and a safety margin of 0.50 m, and 1.41 m stays under the keel. If the answer is negative you are short of water, and if the water depth is less than the draft the keel would be aground. Enter the charted depth and draft in the clearance section of the calculator and it works the figures out for your time, and checks them against the sine curve too.

      What is the earliest time with enough water?

      The earliest time with enough water is the first moment on a rising tide when the tide height reaches the height you need, which is your draft plus your safety margin minus the charted depth. In the metric example the height needed is 1.80 plus 0.50 minus 1.20, which is 1.10 m of tide, and the tide reaches it 1 hour 2 minutes after low water by the rule of twelfths, or 1 hour 10 minutes by the sine curve. On a falling tide the same calculation gives the latest time with enough water, the moment to be back across the bar. The calculator rounds these times in the safe direction to whole minutes: the earliest time rounds up and the latest time rounds down.

      When does the rule of twelfths not work?

      The rule assumes a regular semidiurnal tide with about six hours between high and low water and a smooth, symmetrical curve. It does not work where the tide has a double high water, as in the Solent and Poole Harbour, or a double low water, as in Weymouth Bay. It is unreliable in shallow estuaries where the flood runs much faster than the ebb, and it does not apply to diurnal tides, with one high water and one low water a day, as on parts of the US Gulf Coast. It also ignores weather: strong winds and storm surges move real water away from the predicted curve by a foot or more. The calculator warns when the time between tides falls outside 5 to 7 hours, which catches the worst cases, but in any of these waters you should use the port's own tidal curve or the official predictions instead.

      Do I need to correct for daylight saving time or time zones?

      Yes, and forgetting is the most common tidal mistake after mixing up feet and meters. Tide tables are usually printed in local time, including daylight saving time in summer, but some forecasting tools stay on UTC. An hour's error at mid-tide is a quarter of the range, which on an 8.71 ft tide is over 2 ft. Check the time zone printed on your tide table, check the time zone of your plan, and make them match before you enter the times. Heights have their own version of the same trap: US tables use MLLW, mean lower low water, while UK charts use chart datum, and the two are close but not the same. Use heights and charted depths on the same datum, or the clearance will be wrong by the difference between the datums.