Anchor Size and Rode Calculator
Your anchor and rode
How the numbers were worked out
Plan the rest of the trip: our Boat Capacity Calculator checks how many people and how much weight your boat can carry, our Tide Height Calculator works out the tide rise to add to your depth, and our Life Jacket Size Finder sizes a jacket for everyone on board.
Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.
How to use the Anchor Size and Rode Calculator
Anchoring is the skill new boat owners worry about most, and the worry is justified: an undersized anchor drags, and a dragging anchor at 2 a.m. in a rising wind is a genuine emergency. This calculator sizes the whole ground tackle system for your boat, not just the anchor. Enter your boat length and loaded displacement, pick your anchor type and the bottom you anchor on, say what conditions you expect, and enter the depth, bow height, and tide rise. The calculator gives you the anchor weight, the scope ratio, the total rode to pay out, the chain and rope split, the chain and rope diameters, the swing room to allow, and the expected load on the system checked against the working load limit of the chain. Every figure is worked out in the open, in the steps section under the result, so you can check each one against the published tables it comes from.
The calculator is built on the published sizing tables, not on rules of thumb invented for the page. The anchor weights come from the West Marine anchor-selection guide, which pairs boat length and approximate displacement with weights for fluke, plow, scoop, and claw anchors. The scope ratios follow West Marine and Mantus practice: 5:1 as a minimum, 7:1 for normal overnight anchoring, 10:1 in a storm. The loads come from the ABYC horizontal working load table, published by Mantus Marine. The chain sizes come from Mantus chain-sizing recommendations, and the rope rule, 1/8 inch of diameter per 9 feet of boat, is the standard West Marine rule. Where the sources disagree, the calculator takes the heavier, more conservative figure and says so. The sources section at the bottom of this page lists every table with its publisher.
Read the safety note before you trust any number here. This is planning guidance only: severe weather needs heavier tackle, and the chart is a minimum. Always check your anchor maker's own sizing table before you buy. A chart weight is a floor, not a guarantee: holding depends on the anchor design, the bottom, your boat's windage, how well you set the anchor, and the scope you actually pay out. Rocna builds its chart on 50 knots of wind, surge, and a poor bottom; Mantus publishes separate day, cruising, and storm columns because the same boat needs a different anchor in different weather. If you sit between two sizes, take the larger one. The cost of a heavier anchor is small next to the cost of dragging onto a lee shore.
To get your result, follow these steps:
- Enter your boat length. Length overall in feet, from the tip of the bow to the end of the stern, not counting a bowsprit or a swim platform. Length sets the first sizing band: up to 20 feet, 20 to 25, 25 to 35, 35 to 45, 45 to 60, and over 60. The tool covers boats from 8 to 90 feet. A boat over 90 feet needs classification-society sizing, not a general chart, and the calculator says so rather than guessing.
- Enter your displacement, if you know it. Displacement is the fully loaded weight of the boat in the water: hull plus fuel, water, gear, provisions, and crew. It is the number that actually decides the load on the anchor, and two boats of the same length can differ by thousands of pounds. If you leave it blank, the calculator uses the typical displacement for your length band, which is the top of the band's weight range, and tells you it did so. Check the builder's plate or the owner's manual for the dry weight, then add the tanks, gear, and crew. A heavy boat sizes up even at the same length: a 30 foot boat at 20,000 pounds takes a bigger anchor than a 30 foot boat at 8,000 pounds. Our Boat Capacity Calculator works out how much weight your boat can carry, which helps if you are unsure how much gear counts toward the loaded figure.
- Pick your anchor type. New-generation scoop anchors (Rocna, Mantus, Spade, Vulcan) set fast and hold more per pound than older designs. Classic plow anchors (Delta, CQR) are the long-standing standard. Claw anchors (Bruce style) set easily and work in most conditions but struggle on hard bottoms and in heavy grass. Fluke anchors (Danforth style) are light for their hold in sand and mud but set poorly on rock and in weed. The chart gives the same weight for plow, scoop, and claw, and a lighter weight for fluke, because a fluke holds more per pound in the bottoms it suits. If you are buying new and anchor on mixed bottoms, a scoop is the usual recommendation; if you anchor only on sand and mud and want the lightest anchor, a fluke is worth considering.
- Pick the bottom type. Sand is the friendliest bottom: most anchor types set well in it. Soft mud holds far less than sand, and the calculator warns you about it. Rock and gravel defeat fluke anchors, which cannot dig and can bend on a hard bottom. Weed and grass defeat fluke and claw anchors, which skate over the top instead of biting through. The bottom does not change the anchor weight in this calculator, because no published chart scales weight by bottom; instead it changes the warnings, so a bad pairing is flagged in plain language.
- Pick the conditions. A day stop in calm weather uses 5:1 scope and the day weight. Overnight anchoring uses 7:1 scope, the ratio West Marine calls the one that gives the anchor its designed holding under normal conditions. Storm conditions step the anchor up one size and use 10:1 scope, following the Fortress and West Marine guidance that storm anchoring needs an anchor one or two sizes larger. If you expect the weather to turn overnight, size for the storm, not for the calm evening you arrived in.
- Enter the water depth. The depth where you will drop the anchor, in feet. Scope is measured from the seabed to the bow roller, so depth is only the first part of the total. If you anchor in a tidal area, use the depth at high water, or enter the low-water depth and add the tide rise in the next field.
- Enter the bow height. The height of your bow roller above the water, in feet. The default is 3 feet, which suits a typical small to mid-size cruiser. A high-freeboard boat can have 5 or 6 feet here, and it matters: in 10 feet of water with a 5 foot bow height, the scope is measured on 15 feet, not 10, so 7:1 scope needs 105 feet of rode, not 70. Forgetting the bow height is the most common scope mistake.
- Enter the tide rise. How much the water will rise while you are at anchor, in feet. Size the rode for high water, not for the depth you measured when you arrived at low tide. In a 6 foot tidal range, a boat that anchored at low water in 10 feet will be sitting in 16 feet at high water, and the scope you paid out for 10 feet is suddenly far too short. Our Tide Height Calculator works out the rise for your time on anchor.
- Pick the rode type. Chain leader plus nylon rope is the standard setup: the chain keeps the pull low and resists chafe on the bottom, and the nylon stretches and absorbs shock loads. All-chain rode is heavier, holds a better catenary, and needs no rope, but it transmits shock loads straight to the anchor unless you use a snubber. The calculator splits the rode into chain and rope for the mixed setup, and gives the full length as chain for the all-chain setup.
The tool updates as you type, so you can try different numbers quickly. Try the example buttons under the form: the defaults show a 35 foot cruiser anchoring overnight in 15 feet of water; the second is a 24 foot day boat with a fluke anchor on a calm lunch stop; the third is a heavy 45 foot cruiser riding out a storm on all-chain rode; and the fourth is a 40 foot boat that is heavy for its length, anchoring on rock. The four examples show the four shapes the answer takes: a standard overnight setup, a light day setup, a storm setup where the load check fires, and a case where displacement, not length, governs the size.
Read the full result, not just the headline. The headline leads with your anchor weight and total rode. The cards show the chart range, the scope, the total rode, the chain length and size, the rope length and diameter, the swing radius, and the expected load. The guidance explains the result in plain language, including whether your displacement governed the size and whether the storm step-up applied. The warnings flag the pairings and limits that need a second look: a boat above the chart, a storm with no step-up left, a chain whose working load limit is below the expected load, and a bottom the chosen anchor type handles poorly. The steps print the full working so you can check every figure, and the notes carry the standing facts: the scope definition, the 300 foot rode minimum for a cruising boat, the multihull rule, and the reminder to round up to the next size your brand makes.
How it works
The calculator runs eight steps in order: the sizing band, the chart weight, the storm step-up, the scope, the total depth, the rode length, the chain and rope split, and the load check. Each step uses the result of the one before it, and the steps section on the page prints all eight so you can check them against your own arithmetic and against the published tables.
Step 1: the sizing band
Your boat falls into one of six bands by length and one of six bands by displacement. The length bands are up to 20 feet, 20 to 25, 25 to 35, 35 to 45, 45 to 60, and over 60. The displacement bands are up to 2,500 pounds, 2,500 to 5,000, 5,000 to 10,000, 10,000 to 20,000, 20,000 to 40,000, and over 40,000. The higher of the two bands governs. This is the Rocna method: length picks the row, then displacement picks the size, and a heavy boat takes the larger anchor. A 30 foot boat at 8,000 pounds is band 2 by both measures. A 30 foot boat at 15,000 pounds is band 2 by length and band 3 by displacement, so band 3 governs and the anchor is one size up. If you leave displacement blank, the calculator uses the typical displacement for the length band, which is the top of that band's weight range, so the length band and the displacement band agree and the length governs.
Band boundaries belong to the lower band: a boat of exactly 25 feet is in the 20 to 25 foot band, and a displacement of exactly 5,000 pounds is in the 2,500 to 5,000 pound band. If your boat sits exactly on a boundary, consider going up one band anyway: the chart is a minimum, and a boat at the top of a band is carrying the heaviest load that band is meant for.
Step 2: the chart weight
Each band and anchor type has a weight range in the West Marine chart. For a plow, scoop, or claw anchor the ranges are 7 to 10 pounds up to 20 feet, 10 to 15 pounds at 20 to 25 feet, 15 to 25 pounds at 25 to 35 feet, 25 to 35 pounds at 35 to 45 feet, 35 to 55 pounds at 45 to 60 feet, and 55 pounds or more over 60 feet. For a fluke anchor the ranges are 4 to 8, 8 to 13, 13 to 22, 22 to 35, 35 to 60, and 60 pounds or more. The calculator recommends the top of the range, because the chart is a minimum and the top of the range is the weight that covers the heaviest boat in the band. A 35 foot boat takes the 25 pound top of the 15 to 25 pound range, not the 15 pound bottom. The top band is open-ended in the guide, so the calculator reports the floor value, 55 or 60 pounds, and warns that a boat this size needs the maker's own table for a settled size.
Step 3: the storm step-up
Storm conditions step the anchor up one band. A boat in band 2 takes the band 3 weight; a boat in band 4 takes the band 5 weight. This follows the Fortress selection guide, which says to use an anchor one or two sizes larger for storm conditions, and the West Marine guidance, which names heavy weather as a reason to size up. The step-up is one band, the conservative end of the published advice, and the result says plainly that it applied. If the boat is already in the top band, no step-up is available, and the calculator warns that a storm anchor for this boat must come from the maker's own table. The step-up applies to the weight only; the scope step-up is handled separately in the next step.
Step 4: the scope ratio
Scope is the ratio of rode paid out to the height from the seabed to the bow roller. The calculator uses 5:1 for a calm day stop, 7:1 for overnight anchoring, and 10:1 for storm conditions. West Marine recommends at least 5:1 and preferably 7:1, and says most anchoring references and manufacturers agree that 7:1 gives the anchor its designed holding performance under normal conditions. Mantus calls 10:1 preferable in windy conditions and says many cruisers find it a good compromise between rode length and holding power. The holding power table in the scope section below shows why: at 2:1 scope an anchor develops only about 10 percent of its maximum holding power, at 4:1 about 55 percent, at 6:1 about 70 percent, and at 10:1 about 85 percent. Short scope is the fastest way to turn a good anchor into a bad one.
Step 5: the total depth
Total depth is the water depth plus the bow height plus the tide rise you will swing through. This is the height the scope ratio multiplies, and it is the step most people get wrong, because they measure scope on the water depth alone. A boat in 15 feet of water with a 3 foot bow roller and no tide rise has a total depth of 18 feet. The same boat with a 2 foot tide rise has a total depth of 20 feet, and at 7:1 scope the rode grows from 126 feet to 140 feet. Always size for the deepest water you will sit in, not the shallowest.
Step 6: the rode length
Rode length is the scope ratio times the total depth, rounded up to the next 5 feet. Rounding up matters: rounding down would leave you short of the scope you chose. At 7:1 in 18 feet the raw figure is 126 feet, which rounds up to 130 feet. At 5:1 in 12 feet the raw figure is 60 feet exactly, so no rounding is needed. The calculator shows both the raw figure and the rounded figure in the steps, so you can see whether rounding applied.
Step 7: the chain and rope split
The chain leader is the longer of two rules: one foot of chain per foot of boat length, and 6 feet of chain for every 25 feet of water depth. The first rule comes from the standard anchor-rode guides; the second comes from the Fortress selection guide. For a 35 foot boat in 15 feet of water, the length rule gives 35 feet and the depth rule gives 6 feet, so the leader is 35 feet. For a 33 foot boat in 150 feet of water, the length rule gives 33 feet and the depth rule gives 36 feet, so the leader is 36 feet. The rope makes up the rest of the rode. If the chain leader is longer than the total rode, which happens with a long boat in shallow water at short scope, the rode is all chain and the calculator says so. For an all-chain rode, the whole length is chain and there is no rope.
Chain size follows the Mantus chain-sizing recommendations for BBB chain: 1/4 inch up to 20 feet, 5/16 inch at 20 to 35 feet, 3/8 inch at 35 to 45 feet, 7/16 inch at 45 to 60 feet, 1/2 inch at 60 to 70 feet, and 5/8 inch at 70 to 90 feet. A boundary length takes the smaller size, and the load check in the next step catches a chain that is too light for the expected load. Rope diameter follows the West Marine rule of 1/8 inch per 9 feet of boat, rounded up to the next stock size, with 3/8 inch as the smallest size. A 35 foot boat needs 4 eighths, which is 1/2 inch; a 45 foot boat needs 5 eighths, which is 5/8 inch; a 90 foot boat needs 10 eighths, which is 1 1/4 inch.
Step 8: the load check
The expected load comes from the ABYC horizontal working load table, interpolated for your exact boat length. The table gives loads at 15 knots (lunch hook), 30 knots (working), and 42 knots (storm) for boats of 20, 25, 30, 35, 40, 50, and 60 feet. A 35 foot boat sees 225 pounds at 15 knots, 900 pounds at 30 knots, and 1,800 pounds at 42 knots. A 24 foot boat at 15 knots interpolates between the 20 foot and 25 foot values: 90 plus 35 times 4 fifths, which is 118 pounds. Below 20 feet the table's 20 foot value stands; above 60 feet the 60 foot value stands. The calculator compares the load with the working load limit of the recommended BBB chain. If the load is higher, it warns you and names the fix: go up one chain size, or switch to high-test (G43) chain, whose working load limit at the same size is about 50 percent higher. The load table is the worst shock load on a chain-only rode; a nylon rode or a snubber cuts shock loads by about a factor of 3, but the rode must still handle the table load alone if the snubber fails, which is why the check uses the full table figure.
Worked example 1: the defaults, overnight
A 35 foot cruiser, displacement left blank, new-generation scoop anchor, sand bottom, overnight, 15 feet of water, 3 foot bow height, no tide rise, chain plus rope rode.
- Length 35 ft is band 3 (25 to 35 ft). No displacement was entered, so the typical 10,000 lb for the band was used, which is also band 3. The higher band governs: band 3.
- Chart weight for a scoop anchor in band 3: 15 to 25 lb. The top of the range, 25 lb (11.3 kg), is the recommendation.
- Scope for overnight anchoring: 7:1.
- Total depth: 15 ft of water plus 3 ft of bow height plus 0 ft of tide rise = 18 ft.
- Rode: 7 x 18 = 126 ft, rounded up to 130 ft.
- Chain leader: the longer of 35 ft (one foot per foot of boat) and 6 ft (6 ft per 25 ft of water) = 35 ft. Rope: 130 - 35 = 95 ft.
- Chain size for a 35 ft boat: 5/16 in. Rope diameter: 35 / 9 = 3.89, rounded up to 4 eighths, which is 1/2 in.
- Expected load at 30 knots (ABYC table, 35 ft): 900 lb. Working load limit of 5/16 in BBB chain: 1,900 lb. The chain is well above the load.
- Swing radius: 130 ft of rode plus 35 ft of boat = 165 ft.
Worked example 2: a light day boat with a fluke anchor
A 24 foot day boat, 4,000 lb displacement, fluke anchor, sand bottom, calm day stop, 10 feet of water, 2 foot bow height, no tide rise, chain plus rope rode.
- Length 24 ft is band 2 (20 to 25 ft). Displacement 4,000 lb is band 2 (2,500 to 5,000 lb). The higher band governs: band 2.
- Chart weight for a fluke anchor in band 2: 8 to 13 lb. The top of the range, 13 lb (5.9 kg), is the recommendation.
- Scope for a day stop in calm weather: 5:1.
- Total depth: 10 ft of water plus 2 ft of bow height plus 0 ft of tide rise = 12 ft.
- Rode: 5 x 12 = 60 ft.
- Chain leader: the longer of 24 ft and 6 ft = 24 ft. Rope: 60 - 24 = 36 ft.
- Chain size for a 24 ft boat: 1/4 in. Rope diameter: 24 / 9 = 2.67, rounded up to 3 eighths, which is 3/8 in.
- Expected load at 15 knots (ABYC table, 24 ft): 118 lb. Working load limit of 1/4 in BBB chain: 1,300 lb.
- Swing radius: 60 ft of rode plus 24 ft of boat = 84 ft.
Worked example 3: a heavy cruiser in a storm
A 45 foot cruiser, 30,000 lb displacement, new-generation scoop anchor, soft mud bottom, storm conditions, 20 feet of water, 4 foot bow height, 2 foot tide rise, all-chain rode.
- Length 45 ft is band 4 (35 to 45 ft). Displacement 30,000 lb is band 5 (20,000 to 40,000 lb). Displacement governs: band 5.
- Chart weight for a scoop anchor in band 5 is 35 to 55 lb. Storm conditions step the anchor up one band, to band 6 (over 60 ft): 55 lb or more. The 55 lb (24.9 kg) chart minimum is the recommendation, with a warning that a boat this size needs the maker's own table.
- Scope for storm conditions: 10:1.
- Total depth: 20 ft of water plus 4 ft of bow height plus 2 ft of tide rise = 26 ft.
- Rode: 10 x 26 = 260 ft, all chain.
- Chain size for a 45 ft boat: 3/8 in. Rope diameter, if a rope tail is added: 45 / 9 = 5, which is 5/8 in.
- Expected load at 42 knots (ABYC table, 45 ft): 2,800 lb. Working load limit of 3/8 in BBB chain: 2,650 lb. The load is above the limit, so the calculator warns: go up one chain size, or switch to high-test (G43) chain, whose working load limit is 4,050 lb at this size.
- Swing radius: 260 ft of rode plus 45 ft of boat = 305 ft.
- Warnings: the boat is above the top row of the general chart, the chain limit is exceeded, and soft mud holds about a third as much as hard sand.
Worked example 4: displacement governs
A 40 foot boat, 35,000 lb displacement, plow anchor, rock bottom, overnight, 12 feet of water, 3 foot bow height, 1 foot tide rise, chain plus rope rode.
- Length 40 ft is band 4 (35 to 45 ft). Displacement 35,000 lb is band 5 (20,000 to 40,000 lb). Displacement governs: band 5. By length alone the chart would give 35 lb; displacement moves it to 55 lb.
- Chart weight for a plow anchor in band 5: 35 to 55 lb. The top of the range, 55 lb (24.9 kg), is the recommendation.
- Scope for overnight anchoring: 7:1.
- Total depth: 12 ft of water plus 3 ft of bow height plus 1 ft of tide rise = 16 ft.
- Rode: 7 x 16 = 112 ft, rounded up to 115 ft.
- Chain leader: the longer of 40 ft and 6 ft = 40 ft. Rope: 115 - 40 = 75 ft.
- Chain size for a 40 ft boat: 3/8 in. Rope diameter: 40 / 9 = 4.44, rounded up to 5 eighths, which is 5/8 in.
- Expected load at 30 knots (ABYC table, 40 ft): 1,200 lb. Working load limit of 3/8 in BBB chain: 2,650 lb.
- Swing radius: 115 ft of rode plus 40 ft of boat = 155 ft.
The anchor size chart
The table below is the West Marine anchor-selection guide, the chart the calculator is built on. Find your boat length, then your displacement, and take the higher band. The weight shown is a range; the calculator recommends the top of the range. Plow, scoop, and claw anchors share one column in the guide, because their holding per pound is close enough that the guide does not split them. Fluke anchors get their own, lighter column, because a fluke holds more per pound in the sand and mud bottoms it is made for.
| Boat length | Typical displacement | Fluke (Danforth style) | Plow, scoop, or claw |
|---|---|---|---|
| Up to 20 ft | Up to 2,500 lb | 4 to 8 lb | 7 to 10 lb |
| 20 to 25 ft | 2,500 to 5,000 lb | 8 to 13 lb | 10 to 15 lb |
| 25 to 35 ft | 5,000 to 10,000 lb | 13 to 22 lb | 15 to 25 lb |
| 35 to 45 ft | 10,000 to 20,000 lb | 22 to 35 lb | 25 to 35 lb |
| 45 to 60 ft | 20,000 to 40,000 lb | 35 to 60 lb | 35 to 55 lb |
| Over 60 ft | Over 40,000 lb | 60 lb or more | 55 lb or more |
The guide is explicit that these are general guidelines, not a substitute for the chart of the anchor you plan to buy. West Marine says to consider displacement and windage as well as where, and in what weather, you anchor, and names high windage, exposed anchorages, and heavy weather as reasons to size up. A flybridge cruiser, a boat with a tall cabin structure, or a catamaran presents far more windage than an open boat of the same length, and windage drives the load more than hull length does. If your boat is tall, heavy, or wide for its length, take the larger size.
Cross-check: Mantus
Mantus Marine publishes the most detailed maker table in the business: three columns for every anchor size, day (winds under 30 knots), cruising (winds under 50 knots), and storm (winds over 50 knots). Mantus says most cruisers should size from the cruising column, and that its ratings are conservative, chosen with poor bottoms and higher wind in mind. The M1 comes in sixteen sizes from 2.5 lb to 220 lb. A 25 lb Mantus is a day anchor for a 30 to 35 foot boat under 15,000 lb, a cruising anchor for a 25 to 30 foot boat under 11,000 lb, and a storm anchor for a 20 to 25 foot boat under 5,000 lb. A 35 lb Mantus is a day anchor for a 35 to 39 foot boat under 20,000 lb, a cruising anchor for a 30 to 35 foot boat under 15,000 lb, and a storm anchor for a 25 to 30 foot boat under 11,000 lb. A 45 lb Mantus is a day anchor for a 39 to 43 foot boat under 30,000 lb, a cruising anchor for a 35 to 39 foot boat under 20,000 lb, and a storm anchor for a 30 to 35 foot boat under 15,000 lb. A 55 lb Mantus is a cruising anchor for a 39 to 43 foot boat under 30,000 lb. Compare those with the West Marine tops: 35 feet takes 25 lb in the guide and 35 lb as a Mantus cruising anchor; 45 feet takes 55 lb in the guide and 55 lb as a Mantus cruising anchor. The guide and the maker agree within one size at 30 to 60 feet, which is the range most cruisers sit in. At smaller sizes the guide runs lighter than the Mantus cruising column, because the guide is a general minimum and the Mantus cruising column is built for 50 knots. If you cruise overnight in exposed water, the Mantus cruising column is the safer reference, and the calculator's storm step-up moves you toward it.
Cross-check: Rocna
Rocna sizes by length and displacement together, in a matrix: length picks the row, then displacement picks the size, and multihulls go up one size from the chart result. The Rocna Original comes in 4, 6, 10, 15, 20, 25, 33, 40, 55, 70, and 110 kg models, which are 9, 13, 22, 33, 44, 55, 73, 88, 121, 154, and 243 lb. Rocna bases its chart on 50 knots of wind, associated surge, and poor holding bottoms, and calls it a guideline only. In round numbers the chart puts a 32 to 36 foot boat of 10,000 to 15,000 lb on the 15 kg (33 lb) model, a 36 to 40 foot boat of 15,000 to 20,000 lb on the 20 kg (44 lb) model, and a 40 to 45 foot boat of 20,000 to 30,000 lb on the 25 kg (55 lb) model. Rocna's recommended G40 chain runs 1/4 inch up to the 10 kg model, 5/16 inch for the 12 to 20 kg models, 3/8 inch for the 25 and 33 kg models, 7/16 inch for the 40 and 55 kg models, 1/2 inch for the 70 kg model, and 5/8 inch for the 110 kg model. Rocna's numbers run heavier than the West Marine guide at small sizes, for the same reason Mantus cruising numbers do: the chart assumes 50 knots and a poor bottom. The calculator's weights sit between the West Marine minimum and the Rocna figure, and the storm step-up closes the gap for boats that anchor in exposed water.
Cross-check: Fortress and the fluke family
Fortress makes aluminum fluke anchors, and its selection guide shows how much lighter a fluke can be for the same hold. The FX-7 weighs 4 lb and covers boats of 16 to 27 feet; the FX-11 weighs 7 lb for 28 to 32 feet; the FX-16 weighs 10 lb for 33 to 38 feet; the FX-23 weighs 15 lb for 39 to 45 feet; the FX-37 weighs 21 lb for 46 to 51 feet; the FX-55 weighs 32 lb for 52 to 58 feet; the FX-85 weighs 47 lb for 59 to 68 feet; and the FX-125 weighs 69 lb for 69 to 150 feet. Fortress says its anchors replace steel fluke anchors roughly twice their weight: the 4 lb FX-7 replaces a 6 to 9 lb steel fluke, and the 15 lb FX-23 replaces a 19 to 28 lb steel fluke. The guide's recommendations assume average windage and proportions, 30 knots of wind, average bottom conditions, and moderate protection from open seas, and it says to use an anchor one or two sizes larger for storm conditions. Fortress also publishes holding power figures that show why bottom matters so much: the FX-7 holds 2,800 lb in hard sand at a 32 degree fluke angle, but only 840 lb in soft mud at 45 degrees and 420 lb in soft mud at 32 degrees. The same anchor holds less than a third as much in soft mud as in hard sand, which is why the calculator warns about mud on every bottom selection, whatever the anchor type.
Cross-check: the Vigor rule
Master mariner John Vigor's table, published in The Seaworthy Offshore Sailboat, gives a baseline plow weight by length: under 22 feet, 11 lb; 22 to 25 feet, 22 lb; 26 to 30 feet, 25 lb; 31 to 40 feet, 35 lb; 41 to 45 feet, 44 lb. Lightweight anchors (Danforth, Fortress) take half the plow weight; storm anchors take twice the table weight; heavy displacement or higher freeboard takes one size larger. Vigor's plow figures are close to the West Marine tops: 35 lb at 31 to 40 feet against the guide's 35 lb top at 35 to 45 feet, and 44 lb at 41 to 45 feet against the guide's 35 lb top. The agreement across four independent sources, West Marine, Mantus, Rocna, and Vigor, is what makes the chart trustworthy: no single table is gospel, but when four tables put a 35 foot boat at 25 to 35 lb, the range is real.
Why the calculator recommends the top of the range
Every published chart is a minimum for average conditions and an average bottom. The bottom of a range covers the lightest boat in the band in fair weather on a good bottom; the top covers the heaviest boat in the band. Most boats sit in the middle of their band, and most anchorages are not perfect, so the top of the range is the honest recommendation. It also matches how makers sell anchors: brands sell fixed sizes, and the next size up from the bottom of a range is usually the top of the range anyway. A 35 foot boat that takes the 15 lb bottom of the 15 to 25 lb range would buy a 15 lb anchor; the same boat taking the top buys a 25 lb anchor, which is the size Mantus and Rocna put on a 35 foot boat. The extra 10 lb costs little, stows the same way, and holds measurably more. When in doubt, go up one size: the cost of a heavier anchor is small next to the cost of dragging.
Scope: how much rode to pay out
Scope is the ratio of rode paid out to the height from the seabed to the bow roller. It is the single most important number in anchoring after the anchor itself, because scope decides the angle of pull on the anchor, and the angle decides how much of the anchor's holding power you actually get. A short rode pulls upward on the shank and levers the anchor out of the bottom. A long rode pulls almost horizontally, and the anchor digs in and stays dug in. Mantus publishes the relationship as a table: at 2:1 scope the anchor develops about 10 percent of its maximum holding power, with the pull 30 degrees above horizontal; at 3:1 about 40 percent at 19.5 degrees; at 4:1 about 55 percent at 14 degrees; at 6:1 about 70 percent at 9.5 degrees; at 8:1 about 80 percent at 7 degrees; at 10:1 about 85 percent at 5 degrees; and at 20:1 about 89 percent at 2.8 degrees. The curve flattens after 10:1, which is why Mantus calls 10:1 a good compromise between rode length and holding power, and why going from 5:1 to 7:1 buys more holding than going from 10:1 to 20:1.
| Scope | Holding power | Pull angle above horizontal |
|---|---|---|
| 2:1 | About 10 percent | 30 degrees |
| 3:1 | About 40 percent | 19.5 degrees |
| 4:1 | About 55 percent | 14 degrees |
| 6:1 | About 70 percent | 9.5 degrees |
| 8:1 | About 80 percent | 7 degrees |
| 10:1 | About 85 percent | 5 degrees |
| 20:1 | About 89 percent | 2.8 degrees |
The three scope ratios in this calculator follow the published consensus. West Marine recommends at least 5:1 and preferably 7:1, and says 7:1 gives the anchor its designed holding under normal conditions. Discover Boating, the National Marine Manufacturers Association's boating site, recommends 7:1 when there is room. BoatTEST and Boatsetter both give 7:1 as the standard recommendation for normal conditions, with 5:1 acceptable in calm weather for smaller pleasure boats. Mantus calls 10:1 preferable in windy conditions and recommends that an average cruising boat carry at least 300 feet of rode, which allows 10:1 scope in 25 feet of water with 5 feet of freeboard. In a crowded anchorage you may not have room for 7:1, and West Marine notes that 5:1 or even 3:1 can work in calm conditions in a crowd, but warns that short scope increases the pull angle and reduces holding reliability if the wind or current shifts. If you must anchor short, set the anchor carefully, test it hard in reverse, and watch it.
All-chain rode changes the scope picture, because chain is heavy and its catenary, the sag in the rode, keeps the pull low even at shorter scope. A published rule of thumb puts the normal minimum at 5:1 for all-chain rode against 7:1 for rope rode. This calculator keeps the same scope for both rode types, which is the conservative choice: the chain's catenary straightens out in strong wind, and at the moment you need the holding most, the chain is bar-tight and the scope is all you have. If you anchor all-chain at 5:1 in settled weather, you are following a recognized practice, but the calculator's 7:1 figure is the safer number to carry in your head.
Scope is measured on the total depth, not the water depth. The worked examples show how much this matters: in 15 feet of water with a 3 foot bow height, 7:1 scope is 126 feet of rode, not 105. In 10 feet of water with a 5 foot bow height and a 2 foot tide rise, 7:1 scope is 119 feet, not 70. Every foot of bow height and tide rise adds 7 feet of rode at 7:1 scope, and 10 feet at storm scope. The calculator adds all three heights before multiplying, and shows the addition in the steps so you can see exactly what went into the total.
Swing room
When the wind or tide shifts 180 degrees, your bow can reach anywhere within the rode length plus the boat length of the anchor. That is the swing circle, and it is the space you must have clear of hazards, other boats, and shallow water. The calculator reports the swing radius as the rode length plus the boat length: 130 feet of rode plus a 35 foot boat is a 165 foot radius, which is a 330 foot circle. In a crowded anchorage, swing room is often the binding constraint on scope: you cannot pay out 10:1 if the boat next door is 100 feet away. When room is short, the honest trade is a bigger anchor at shorter scope, or a different anchorage. Never let the swing circle overlap another boat's circle on the assumption that both boats will swing the same way: a boat on all-chain rode swings differently from a boat on rope, a catamaran swings differently from a monohull, and a boat with more windage swings first.
Chain and rope: sizing the rode
The rode is the chain and rope between the anchor and the boat, and it is a system: the anchor, the chain, the rope, the shackles, and the cleats must all be strong enough for the same load. The weakest link decides the strength of the system, and it is often not the anchor. A 35 lb anchor on 1/4 inch chain with a 1,300 lb working load limit is held back by the chain long before the anchor gives way. This calculator sizes the chain and rope to the boat and checks the chain against the expected load, so a weak link shows up in the warnings rather than at 2 a.m.
Chain size
Chain size follows the Mantus chain-sizing recommendations for BBB chain. BBB is short-link chain, made for windlasses: the short links bend easily around the gypsy and stow compactly. The table gives one size per boat-length band, with the displacement the band is built for.
| Boat size | BBB or proof-coil chain | High-test (G43) chain |
|---|---|---|
| 0 to 14 ft, 1,000 lb | 1/4 in | 1/4 in |
| 14 to 20 ft, 5,000 lb | 1/4 in | 1/4 in |
| 20 to 30 ft, 11,000 lb | 5/16 in | 1/4 in |
| 30 to 35 ft, 15,000 lb | 5/16 in | 5/16 in |
| 35 to 40 ft, 20,000 lb | 3/8 in | 5/16 in |
| 40 to 45 ft, 40,000 lb | 3/8 in | 3/8 in |
| 45 to 50 ft, 50,000 lb | 7/16 in | 3/8 in |
| 50 to 60 ft, 60,000 lb | 7/16 in | 7/16 in |
| 60 to 70 ft, 70,000 lb | 1/2 in | 7/16 in |
| 70 to 90 ft, 110,000 lb | 5/8 in | 1/2 in |
High-test chain carries the same load at a smaller size, which saves weight in the bow: 300 feet of 3/8 inch BBB chain weighs 468 lb, while 300 feet of 5/16 inch G4 high-test chain weighs 310 lb and is stronger. Mantus notes that a windlass gypsy is cut for one chain size and type, so a gypsy made for 5/16 inch high-test chain will not work on 5/16 inch BBB chain, which has shorter, more compact links. Check the gypsy before changing chain size or type, and never compromise on strength to fit a gypsy: gypsies can be ordered, ground tackle cannot be made stronger after the fact.
Chain strength and the working load limit
The working load limit, also called the safe working load, is the load the chain can safely support without fear of breaking. For most chain it is 1/4 of the ultimate breaking strength; for G43 high-test chain it is 1/3. The table below is the Mantus chain-strength table. The calculator checks the expected load against the BBB working load limit and warns when the load is higher, naming the high-test limit at the same size as the fix.
| Chain size | BBB Grade 30 breaking strength | BBB working load limit | G43 high-test breaking strength | G43 working load limit |
|---|---|---|---|---|
| 1/4 in | 5,200 lb | 1,300 lb | 7,800 lb | 1,950 lb |
| 5/16 in | 7,600 lb | 1,900 lb | 11,700 lb | 2,925 lb |
| 3/8 in | 10,600 lb | 2,650 lb | 16,200 lb | 4,050 lb |
| 7/16 in | 14,800 lb | 3,700 lb | 21,600 lb | 5,400 lb |
| 1/2 in | 18,000 lb | 4,500 lb | 27,600 lb | 6,900 lb |
The table stops at 1/2 inch: the published table used here does not list a working load limit for 5/8 inch chain, so for boats of 70 to 90 feet the calculator sizes the chain at 5/8 inch and tells you to check the working load limit with the chain maker. Stainless steel 316 chain and Grade 70 chain are stronger still at the same size, and duplex stainless is the strongest option in the Mantus table, but they cost far more and are rarely needed on a recreational boat.
Rope diameter
Rope diameter follows the rule of 1/8 inch per 9 feet of boat, rounded up to the next stock size. A 20 foot boat needs 3 eighths, which is 3/8 inch. A 30 foot boat needs 4 eighths, which is 1/2 inch. A 40 foot boat needs 5 eighths, which is 5/8 inch. A 50 foot boat needs 6 eighths, which is 3/4 inch. A 60 foot boat needs 7 eighths, which is 7/8 inch. A 70 foot boat needs 8 eighths, which is 1 inch. The smallest stock size is 3/8 inch, so a boat under 19 feet still takes 3/8 inch rope. Use three-strand nylon for the rope rode: nylon stretches under load, which absorbs the shock of waves and gusts, and that stretch is what keeps the anchor set when the boat surges. Polyester stretches far less and is a poor choice for anchor rode. Rope must be in good condition: the Fortress guide bases its rope recommendations on 25 percent of breaking strength and notes that the rope must be in good condition, because chafe, sun damage, and age all cut the real strength well below the label.
The ABYC load table
The American Boat and Yacht Council developed its load table in the 1950s for the strength of anchors, capstans, rode, and cleats. A past ABYC technical director, Tom Hale, said it is reasonable to apply the figures to the entire anchor system. The table gives the horizontal working load in pounds for four wind speeds and seven boat lengths. The calculator interpolates between the table lengths for your exact boat length, and uses the 15 knot row for calm conditions, the 30 knot row for overnight anchoring, and the 42 knot row for storm conditions.
| Wind speed | Anchor class | 20 ft | 25 ft | 30 ft | 35 ft | 40 ft | 50 ft | 60 ft |
|---|---|---|---|---|---|---|---|---|
| 15 knots | Lunch hook | 90 lb | 125 lb | 175 lb | 225 lb | 300 lb | 400 lb | 500 lb |
| 30 knots | Working | 360 lb | 490 lb | 700 lb | 900 lb | 1,200 lb | 1,600 lb | 2,000 lb |
| 42 knots | Storm | 720 lb | 980 lb | 1,400 lb | 1,800 lb | 2,400 lb | 3,200 lb | 4,000 lb |
| 60 knots | Violent storm | 1,440 lb | 1,960 lb | 2,800 lb | 3,600 lb | 4,800 lb | 6,400 lb | 8,000 lb |
Two things stand out in the table. First, load grows with the square of the wind speed: doubling the wind from 15 to 30 knots multiplies the load by four, and the load at 42 knots is twice the load at 30 knots. A boat that is comfortable at 30 knots is carrying twice the load at 42 knots, which is why the storm step-up and the 10:1 scope matter. Second, the loads are large in absolute terms: a 40 foot boat in a 42 knot storm sees 2,400 lb of horizontal load, which is close to the 2,650 lb working load limit of its 3/8 inch BBB chain. The load table is the worst shock load on a chain-only rode; Mantus notes that a nylon rode or a well-designed snubber cuts shock loads by about a factor of 3, but the rode must still handle the table load alone if the snubber fails. Sizing for a hurricane is not practical for most boats, but sustained winds over 40 knots are commonly met by cruising vessels on anchor, and sizing for those conditions is the reasonable approach.
Bottom types and anchor types
The bottom decides which anchor types set well, and no anchor type is best everywhere. A fluke anchor that holds 2,800 lb in hard sand holds 420 lb in soft mud at the same fluke angle, and may not set at all on rock. A scoop anchor that sets in one boat length on sand can skate across a weed bed. The calculator does not change the weight by bottom, because no published chart scales weight by bottom; instead it warns when the chosen type and bottom are a bad pairing, so you can change the type before you buy.
Sand
Sand is the reference bottom: most anchor types set quickly and hold well in it, and most holding-power figures are measured in sand. A fluke anchor excels in sand, which is why Danforth-style anchors are the standard for sand-bottom anchorages. Scoop and plow anchors set fast in sand and hold well. Claw anchors set easily in sand. If you anchor only on sand, any of the four types works, and the choice comes down to weight, stowage, and price. Hard sand holds more than soft sand, and a thin layer of sand over rock or clay can fool you: the anchor sets in the sand, then the flukes hit the hard layer underneath and stop digging.
Mud
Mud is the most variable bottom. Firm mud holds well; soft mud holds far less than sand. The Fortress figures show the scale: the FX-7 holds 2,800 lb in hard sand, 840 lb in soft mud with the flukes set at 45 degrees, and 420 lb in soft mud at 32 degrees. Fortress flukes adjust to 45 degrees for soft mud, which more than doubles the holding over the 32 degree setting. A scoop or plow anchor with a sharp point and a large fluke area sets best in mud, because it can punch through the soft top layer and find firmer ground below. A fluke anchor works in mud if the fluke angle is right, but a fixed-angle fluke set for sand will underperform. In soft mud, let out full scope, set the anchor with sustained reverse power, and test the set longer than you would on sand. The calculator warns about mud for every anchor type, because the holding drop is a property of the bottom, not of the anchor.
Rock and gravel
Rock and gravel are the hardest bottoms to anchor on, because nothing digs into rock. A fluke anchor sets poorly on rock and gravel and can bend on a hard bottom: the thin flukes are made to slice into sand and mud, not to lever against stone. A claw anchor can skate on hard rock, though its rounded shape is less likely to bend. A plow or scoop anchor has the best chance, because the point can find a crack or a pocket and wedge in, but even a good anchor may drag across a rock bottom until it snags. On rock, the honest advice is to avoid anchoring if you can, and if you cannot, to set carefully, test hard, and be ready to move. Carry a trip line on the anchor crown if you anchor on rock regularly: it lets you pull the anchor out backwards if it wedges. The calculator warns when a fluke or claw anchor is paired with rock, and a scoop or plow anchor is the safer pick there.
Weed and grass
Weed and grass defeat anchors that cannot cut through to the bottom beneath. A fluke anchor struggles to bite through weed: the broad flat flukes ride on top of the weed mat instead of penetrating it. A claw anchor can struggle in heavy grass for the same reason. A scoop or plow anchor with a sharp point and a narrow entry sets more reliably, because the point punches through the weed and the flukes follow. West Marine notes that claws have difficulty in heavy grass, and the same applies to any anchor with a broad, flat leading edge. In weed, drop the anchor, let out scope slowly so the anchor stays upright, and back down firmly: a half-hearted set in weed is a drag waiting to happen. If the anchor comes up with a ball of weed on it, the set never reached the bottom.
Choosing between the four types
If you anchor on mixed bottoms and want one anchor that does most things well, a new-generation scoop is the usual recommendation: it sets fast, holds more per pound than older designs, resets reliably when the wind or tide shifts, and handles sand, mud, and moderate weed. A classic plow is the safe traditional choice and fits most bow rollers well. A claw is a good all-rounder that sets easily, with the known weaknesses on hard bottoms and in heavy grass. A fluke is the lightest anchor for its hold and the best choice for a boat that anchors only on sand and mud, or as a second anchor, because it stows flat and weighs little. Many experienced cruisers carry two anchors of different types: a scoop as the primary and a fluke as the second anchor, so that if the primary cannot set on a strange bottom, the second type has a different chance. The calculator sizes one anchor at a time; run it twice, once per type, to compare.
Features
The calculator sizes the whole ground tackle system in one pass. It takes boat length and loaded displacement together, so a heavy boat sizes up even at the same length, and it uses the typical displacement for the length band when you leave displacement blank. It covers four anchor types, fluke, plow, claw, and new-generation scoop, with the published chart weight for each. It covers four bottom types and warns when the chosen anchor type handles the bottom poorly. It covers three conditions, calm, overnight, and storm, with the scope ratio and the storm step-up for each. It sizes the rode from the total depth, bow height plus water depth plus tide rise, and splits it into chain and rope by the published leader rules. It sizes the chain and rope diameters, checks the expected ABYC load against the chain's working load limit, and reports the swing room to allow. Every result prints the full working in the steps, so any figure can be checked by hand against the tables on this page.
The calculator is honest about its limits. It sizes a primary bower anchor for normal cruising: a day stop, an overnight anchorage, or a storm at anchor. It does not size a storm anchor for a boat already at the top of the chart, and it says so. It does not size ground tackle for a boat over 90 feet, which needs classification-society rules. It does not pretend the chart is a guarantee: the safety wording is in the results on every run, not buried in the fine print. And it does not invent figures: every table on this page comes from a named publisher, and the sources section lists them all with links.
Use cases
Buying your first anchor. You have just bought a 28 foot boat and the previous owner kept the anchor. Enter the length, the loaded displacement from the manual plus your gear, the bottom you anchor on most, and overnight conditions. The calculator gives you the weight to shop for and the chain and rope to buy with it, so you order the whole system once instead of discovering at the chandlery that the chain does not match the anchor.
Checking the anchor you already have. Run the calculator with your boat's numbers and compare the recommended weight with the anchor on your bow. If your anchor is a size below the recommendation, it is not necessarily wrong: the chart is a minimum for average conditions, and a smaller anchor on a good bottom at full scope can hold fine. But if your anchor is two sizes below, or if you anchor overnight in exposed water, the gap is worth closing. The load check is the more important comparison for an existing setup: if the expected load is above your chain's working load limit, the chain is the weak link, whatever the anchor weighs.
Planning a cruise to a new area. You are taking the boat to tidal waters for the first time, or to an anchorage known for soft mud or weed. Run the calculator with the new bottom type and the local tidal range, and see how the rode length and the warnings change. A 6 foot tidal range adds 42 feet of rode at 7:1 scope, which may be more than the rope you carry. A mud bottom changes the warnings and the set technique, even though the weight stays the same.
Upgrading for storm season. You anchor out through the summer and want to know what a storm setup looks like for your boat. Switch the conditions to storm and compare: the anchor steps up one band, the scope goes to 10:1, and the load check may fire. If it fires, the fix is named in the warning: a bigger chain or high-test chain at the same size. Run the numbers before the season, not when the forecast turns.
Sizing a second anchor. Many cruisers carry a second anchor of a different type, often a fluke for sand and mud. Run the calculator once with the fluke type and your usual bottom to size the second anchor, and once with your primary type to compare. The fluke will come out lighter, which is the point: a second anchor you can handle quickly by hand is more useful than a second anchor as heavy as the primary.
Teaching a new crew member. The steps section is a worked lesson in anchoring arithmetic: band, weight, scope, depth, rode, split, diameters, load, swing. Walk a new crew member through it once, and they can size the rode for any anchorage without the calculator. The scope table and the holding-power figures are the part worth memorizing: short scope is the mistake that turns a good anchor into a dragging one.
Checking the numbers before a charter. You are chartering a boat you have never sailed and want to know whether the ground tackle on board is adequate. Enter the charter boat's length and displacement from the charter company's specification, and the bottom and conditions you expect. If the boat's anchor is well below the recommendation, ask the charter company about it before you leave the dock, and plan your anchorages with the shortfall in mind. Our Boat Fuel Cost and Range Calculator helps plan the same charter's fuel stops, and our Boat Ownership Cost Calculator works out what owning the boat would cost against chartering it.
Sources
Every figure on this page comes from a published table. The anchor weights come from the West Marine anchor-selection guide, which pairs boat length and approximate displacement with weights for fluke, plow, scoop, and claw anchors, and recommends at least 5:1 scope and preferably 7:1. The scope and holding-power figures, the ABYC load table, the chain sizes, and the chain strength table come from Mantus Marine's rode-sizing page, which publishes the ABYC horizontal working load table and the scope-to-holding-power relationship. The Mantus day, cruising, and storm sizing columns come from the Mantus M1 anchor page. The Rocna sizing matrix, the multihull rule, and the recommended chain sizes come from the Rocna sizing guide. The Fortress weights, holding-power figures, and chain and scope rules come from the Fortress selection guide. The 7:1 scope recommendation is confirmed by Boatsetter's anchoring guide and by Discover Boating. All sources were re-checked on 20 November 2026.
- Mantus Marine: Chain Sizing and Rode Sizing — scope and holding power, ABYC load table, chain sizes and strength, 300 ft rode minimum.
- Mantus Marine: M1 Mantus Anchor — day, cruising, and storm sizing columns for every M1 size.
- Rocna Anchors Sizing Guide (PDF) — length and displacement sizing matrix, multihull rule, recommended G40 chain.
- Fortress Selection Guide (PDF) — aluminum fluke anchor weights, holding power in sand and mud, chain and scope rules.
- Boatsetter: Anchoring a Boat, Step-by-Step Guide — 7:1 scope recommendation and anchoring technique.
Related tools: our Sailboat Hull Speed Calculator works out your boat's theoretical top speed from its waterline length, our Boat Registration Cost Calculator covers the paperwork for a new boat, our Kayak Size Finder, Canoe Size Finder, and Paddle Board Size Finder size small craft for day trips, our Fishing Rod and Reel Finder matches tackle to the fish you target, and our Scuba Weight Calculator sizes dive weights for the same waters you anchor in.
Frequently asked questions
What size anchor do I need for a 35 foot boat?
A 35 foot boat of typical displacement, about 10,000 lb loaded, takes a 25 lb plow, scoop, or claw anchor, or a 22 lb fluke anchor, from the top of the West Marine chart range for the 25 to 35 foot band. The maker tables run a little heavier: Mantus lists a 35 lb anchor as the cruising size for a 30 to 35 foot boat under 15,000 lb, and Rocna puts a 32 to 36 foot boat of 10,000 to 15,000 lb on its 33 lb model. If your boat is heavy for its length, if you anchor overnight in exposed water, or if you carry a lot of windage, go up one size to 35 lb. The chart weight is a minimum, and the cost of a heavier anchor is small next to the cost of dragging.
How much scope should I use when anchoring?
Use 5:1 scope for a calm day stop, 7:1 for overnight anchoring, and 10:1 in a storm. Scope is the ratio of rode paid out to the height from the seabed to the bow roller, which is the water depth plus the bow height plus the tide rise you will swing through. In 15 feet of water with a 3 foot bow height, 7:1 scope means 126 feet of rode, rounded up to 130 feet. Scope matters because it sets the pull angle on the anchor: at 4:1 scope the anchor develops about 55 percent of its maximum holding power, at 6:1 about 70 percent, and at 10:1 about 85 percent. Short scope is the fastest way to turn a good anchor into a dragging one.
How much chain should I put on my anchor rode?
Use the longer of two rules: one foot of chain per foot of boat length, and 6 feet of chain for every 25 feet of water depth. A 35 foot boat in 15 feet of water takes 35 feet of chain by the length rule, and a 33 foot boat in 150 feet of water takes 36 feet by the depth rule. Chain size follows the Mantus recommendations: 1/4 inch up to 20 feet, 5/16 inch at 20 to 35 feet, 3/8 inch at 35 to 45 feet, 7/16 inch at 45 to 60 feet, 1/2 inch at 60 to 70 feet, and 5/8 inch at 70 to 90 feet. The chain keeps the pull low and resists chafe on the bottom, while the nylon rope stretches and absorbs shock loads. An average cruising boat carries at least 300 feet of rode in total.
Does displacement matter more than boat length for anchor size?
Both matter, and the higher band governs. The sizing chart has six bands by length and six by displacement, and your boat takes the larger of the two. A 30 foot boat at 8,000 lb is band 2 by both measures and takes a 25 lb scoop anchor. The same 30 foot boat at 15,000 lb is band 2 by length and band 3 by displacement, so band 3 governs and the anchor steps up to 35 lb. Displacement is the weight the anchor actually has to hold against wind and current, and two boats of the same length can differ by thousands of pounds once fuel, water, gear, and crew are aboard. If you do not know your displacement, weigh the boat loaded or check the builder's plate, and use the fully loaded figure, not the dry weight.
Which anchor type is best for mud?
A scoop or plow anchor with a sharp point sets best in mud, because the point punches through the soft top layer and the flukes find firmer ground below. A fluke anchor works in mud if the fluke angle suits it: Fortress flukes adjust to 45 degrees for soft mud, and the FX-7 holds 840 lb in soft mud at 45 degrees against 420 lb at 32 degrees. Whatever the type, soft mud holds far less than sand: the same anchor can hold about a third as much in soft mud as in hard sand. In mud, let out full scope, set the anchor with sustained reverse power, and test the set longer than you would on sand. Never trust a quick set in soft mud without a hard pull in reverse.
How do I work out the swing room I need?
Allow a swing radius of the rode length plus the boat length around the anchor. When the wind or tide shifts 180 degrees, your bow can reach anywhere within that circle. A 35 foot boat on 130 feet of rode needs a 165 foot radius, which is a 330 foot circle clear of hazards, other boats, and shallow water. In a crowded anchorage, swing room is often what limits your scope: you cannot pay out 10:1 if the boat next door is 100 feet away. Never assume two boats will swing the same way: a boat on all-chain rode swings differently from a boat on rope, and a catamaran swings differently from a monohull.
Should I size up my anchor for storm conditions?
Yes. Storm conditions step the anchor up one band and use 10:1 scope, following the Fortress guidance to use an anchor one or two sizes larger for storms and the West Marine guidance that heavy weather is a reason to size up. The load table shows why: the ABYC load on a 35 foot boat doubles from 900 lb at 30 knots to 1,800 lb at 42 knots, and doubles again to 3,600 lb at 60 knots. A boat that is comfortable in a fresh breeze is carrying twice the load in a storm, and the anchor and chain sized for the breeze are both working at their limit. If your boat is already at the top of the general chart, no step-up is available from the chart, and the storm anchor must come from the maker's own table.
What size rope and chain go with my anchor?
Rope diameter follows the rule of 1/8 inch per 9 feet of boat, rounded up to the next stock size, with 3/8 inch as the smallest size: a 35 foot boat takes 1/2 inch nylon rope, and a 45 foot boat takes 5/8 inch. Chain size follows the Mantus table by boat length, from 1/4 inch up to 20 feet to 5/8 inch at 70 to 90 feet. The calculator checks the expected load against the chain's working load limit: a 45 foot boat in a 42 knot storm sees a 2,800 lb load, which is above the 2,650 lb working load limit of 3/8 inch BBB chain, so the fix is a bigger chain or high-test chain, whose limit is 4,050 lb at the same size. Use three-strand nylon for the rope: it stretches and absorbs shock loads, which polyester does not.