Boat Capacity Calculator (USCG)
Your boat capacity
How the numbers were worked out
Before you load up: our Life Jacket Size Finder sizes a jacket for each person aboard, our Anchor Size and Rode Calculator sizes the ground tackle for the boat, our Boat Fuel Cost and Range Calculator works out fuel cost and range for the trip, and our Boat Ownership Cost Calculator totals what the boat costs to keep.
Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.
How to use the Boat Capacity Calculator
Every small powerboat in the United States carries, or should carry, a yellow capacity plate that states three limits: how many people it may carry, how much total weight it may carry, and, on an outboard boat, how much horsepower it may carry. The plate is fitted by the builder under the federal rules in 33 CFR Part 183, and it is the legal load limit for that hull. But many boats on the water have no plate to read: older boats built before the rules, boats whose plate has been painted over or lost, home-built boats, and imported boats. Buyers checking a used boat face the same gap. This calculator fills it with the same formulas the federal rules use, so you can work out what the plate would have said.
The calculator answers three questions from the boat's dimensions: how many people it can carry, how much weight it can carry, and how much horsepower it can carry. It uses the Coast Guard rule of thumb for people, length times beam divided by 15, and the federal formulas in 33 CFR 183 for weight and horsepower. It also adjusts the people count for your passengers' real average weight, because the rule of thumb assumes 150-pound people and most adult groups weigh more than that. Read the plate first if your boat has one. The capacity plate on your boat governs, and every number on this page is an estimate for a plate-less boat, never a replacement for the plate.
To get your result, follow these steps:
- Enter the boat length in feet. Measure the longest dimension of the hull, from the tip of the bow to the back of the transom, not counting the motor, the swim platform, or the trailer. Enter a number from 4 to under 20. The federal formulas cover monohull boats under 20 feet, so a boat 20 feet or longer gets an error message and a pointer to the builder's figures instead of a made-up answer.
- Enter the beam, the width, in feet. The beam is the widest point of the hull, measured across the outside of the gunwales. Enter a number from 2 to 12. If the beam you enter is wider than the length, the calculator warns you to check that the two were not swapped, because length is the longest dimension on any real boat.
- Enter the transom width in feet, if you know it. This is the maximum width across the transom, not counting handles, fittings, or extensions. On a boat with no full transom, the regulation uses the broadest beam in the aftermost quarter of the boat's length. The horsepower rating needs this number: the federal factor is length times transom width, not length times beam. Leave it blank if you do not know it, and the calculator will give you the people and weight answers and tell you the horsepower rating needs the transom width.
- Pick the propulsion type. Outboard motor, inboard or sterndrive, or manual propulsion, meaning oars, paddles, or a motor of 2 hp or less. The choice decides which weight formula applies: outboard boats use 33 CFR 183.35, inboard and sterndrive boats use 183.33, and manual or small-motor boats use 183.37. It also decides the horsepower line: inboard boats carry no horsepower rating on the plate, and manual boats are limited to 2 hp by definition.
- Pick the steering type. Tiller steering, where the operator steers by hand on the motor, or remote steering, where a wheel or stick at a helm station steers the motor. Remote steering matters only for the horsepower formula on larger factors, where it takes the higher branch, and only together with a tall enough transom.
- Enter the transom height in inches. Measure from the top of the transom to the bottom of the hull at the centerline. The usual heights are 15 inches for a short shaft, 20 inches for a long shaft, and 25 inches for an extra-long shaft. The default is 20 inches. The remote-steering horsepower branch needs a transom of 20 inches or more, so a remote-steered boat with a 15-inch transom takes the lower branch, and the calculator says so.
- Pick the hull bottom. A flat-bottom hard-chine hull, the shape of most jon boats and flat-bottom skiffs, or a V-hull or other shape. Flat-bottom hard-chine boats drop one step in the horsepower table and take the lower formula branch, because a flat bottom at speed behaves differently from a V-hull.
- Enter the boat weight in pounds, if you know it. The regulation's boat weight is the hull, deck, and superstructure, the permanent fittings, and full built-in fuel tanks. It is the weight the builder lists as the dry hull weight plus permanent gear, not the weight on the trailer. Leave it blank if you do not know it, and the calculator will skip the weight capacity and tell you what it needs.
- Enter the maximum displacement in pounds, if you know it. Maximum displacement is the weight of the water the hull pushes aside when it is immersed level to the point where water would come aboard in calm water. It is a builder's figure, found in the owner's manual or the builder's specifications, and it is the starting point for every weight capacity formula in the regulation. Without it there is no honest weight capacity, so the calculator does not guess one.
- Enter the machinery weight in pounds, for inboard and sterndrive boats. Machinery weight is the combined weight of the installed engines or motors, control equipment, drive units, and batteries. The inboard formula has two branches and the machinery weight drives one of them. Leave it blank and the calculator uses only the displacement branch, which never overstates the capacity, and says so in the result.
- Enter the average weight of each person in pounds. The rule of thumb assumes 150-pound people. If your group averages more, the people count by weight falls below the count by deck space, and the calculator shows the lower number as the advised count, with a warning that the weight limit governs. The default is 150 pounds.
The tool updates as you type, so you can try different numbers quickly. Try the example buttons under the form: the defaults show a 16-foot runabout with a 6-foot beam, 6 people, 900 pounds of people, a weight capacity of 1,100 pounds, and a 50 hp rating; the second is a 14-foot flat-bottom jon boat where the people alone weigh more than the weight capacity, so the calculator warns that the weight capacity governs; and the third is an 18-foot bowrider with remote steering and 180-pound passengers, where the weight check cuts the count from 9 people by deck space to 7. The three examples show the three shapes the answer takes: a clean rating, a rating limited by weight, and a rating limited by passenger weight.
Read the full result, not just the headline. The headline leads with the advised people count, the people weight, and the horsepower rating. The cards show the maximum persons, the people weight, the maximum weight capacity, the maximum horsepower, the motor, fuel, and gear budget, and the horsepower factor. The guidance explains the result in plain language, starting with the sentence that matters most: the capacity plate on your boat governs. The warnings flag the cases that need a second look, the steps print the full working so you can check every figure against the regulation, and the notes carry the scope limits. If your boat has a plate, compare the estimate with it: a big gap usually means the boat's displacement or hull shape differs from the average the formulas assume, and the plate is right.
How it works
The calculator runs four calculations in order: the people count from the rule of thumb, the people count by weight, the maximum weight capacity from the displacement formulas, and the maximum horsepower from the factor table and formulas. Each one uses the results of the ones before it, and the steps section on the page prints all four so you can check them against your own arithmetic and against the regulation.
Step 1: how many people, by deck space
The Coast Guard's boater's guide gives a rule of thumb for a boat without a capacity plate: the maximum number of persons is the boat length in feet times the boat width in feet, divided by 15. The 15 is square feet of deck area per person, and the rule assumes 150-pound people, seated, in good weather. It ignores the hull's displacement, which is why it is a rule of thumb and not a certification: the builder's plate comes from displacement and stability tests that no web page can run. The guide does not say how to round, so this calculator rounds down, so it never adds a person. A 16-foot boat 6 feet wide gives 16 times 6, or 96, divided by 15, which is 6.4, rounded down to 6 people, or 900 pounds at 150 pounds each. A boat 18 feet long by 6 feet wide gives 108 divided by 15, which is 7.2, rounded down to 7 people, or 1,050 pounds. The deck area is rounded to 1 decimal place before the division, so the printed area reproduces the printed count exactly.
For a very small boat the rule of thumb can give less than one person: a 4-foot boat 2 feet wide gives 8 divided by 15, which is 0.53. The calculator shows that as 1 person and warns that the rule gives less than one person for a boat this small, and that the builder's figure and the weight capacity are the numbers to trust. The people weight is the count times 150 pounds: 6 people is 900 pounds, 7 people is 1,050 pounds, 1 person is 150 pounds.
Step 2: how many people, by weight
The rule of thumb counts deck space. The weight check counts pounds. If your passengers average more than 150 pounds, the people weight allows fewer people than the deck does, and the lower number is the advised count. The check divides the people weight by the average weight you entered and rounds down: 900 pounds of people divided by 200 pounds a person is 4.5, rounded down to 4 people, so a 16-foot boat that fits 6 people by deck space advises 4 at 200 pounds each. At 180 pounds a person, 1,350 pounds of people allows 7.5, rounded down to 7. At 300 pounds a person, 900 pounds allows exactly 3. If the average is below 150 pounds, the weight check allows more people than the deck does, and the deck-space count still governs: 900 pounds divided by 100 pounds a person is 9, but the boat still advises 6, because only 6 fit. If the average is so high that even one person exceeds the people weight, the calculator shows 1 person and warns plainly that even one person at that weight is more than the boat is rated for.
This step matters because the 150-pound assumption is old. Average adult weights have risen since the rule was written, and a boat loaded with six 200-pound adults carries 1,200 pounds of people where the rule assumed 900. The calculator keeps the federal 150-pound figure for the rule-of-thumb count, because that is what the rule says, and then lets your real average cut the count. The two numbers are different tools: 150 pounds is the guide's assumption for the space rule, and 141 pounds is the regulation's figure in a different formula, the builder's conversion from tested pounds capacity to a people count, which adds 32 pounds and divides by 141. The two figures answer different questions, and the calculator does not mix them.
Step 3: maximum weight capacity, from displacement
The weight capacity on the plate is the maximum total weight the boat may carry, and it comes from the boat's maximum displacement: the weight of the water the hull displaces when it is immersed level to the point where water would come aboard. The regulation gives a different formula for each propulsion type, and the calculator runs the one that matches the boat you described. Every formula divides the difference between maximum displacement and boat weight by a safety factor, so the capacity is a fraction of the load that would sink the boat, not the sinking load itself.
For an outboard boat, 33 CFR 183.35 sets the maximum weight capacity at one-fifth of the difference between maximum displacement and boat weight. A boat with a maximum displacement of 5,000 pounds and a boat weight of 500 pounds has a capacity of 4,500 divided by 5, which is 900 pounds. That 900 pounds covers the people, the motor, the fuel, and the gear together. For a boat rated for manual propulsion or for a motor of 2 hp or less, 33 CFR 183.37 sets the capacity at three-tenths of the same difference: a boat with a maximum displacement of 1,500 pounds and a boat weight of 150 pounds has a capacity of 3 times 1,350 divided by 10, which is 405 pounds.
For an inboard or sterndrive boat, 33 CFR 183.33 gives two formulas and takes the greater value. The first divides the displacement by 5, subtracts the boat weight divided by 5, and subtracts four times the machinery weight divided by 5. The second divides the difference between displacement and boat weight by 7. At a maximum displacement of 12,000 pounds, a boat weight of 3,000 pounds, and a machinery weight of 800 pounds, the first gives 2,400 minus 600 minus 640, which is 1,160 pounds, and the second gives 9,000 divided by 7, which is 1,285.71 pounds, so the capacity is 1,285 pounds. If no machinery weight is entered, the calculator uses only the second branch, which never overstates the capacity, and says so. A capacity must not exceed its computed value, so the calculator rounds every weight capacity down to whole pounds: 1,285.71 pounds becomes 1,285 pounds, never 1,286.
Once the weight capacity is known, the calculator works out the motor, fuel, and gear budget: the weight capacity minus the weight of the people aboard. A boat with a 1,100-pound capacity and 900 pounds of people has 200 pounds left for the motor, fuel, and gear. A boat with a 900-pound capacity and 900 pounds of people has nothing left, and the calculator warns that the people use the whole capacity. A boat with a 440-pound capacity and 600 pounds of people is 160 pounds over before anything else goes aboard, and the calculator warns that the weight capacity governs and the load must come down. The budget uses the advised people count at the average weight you entered, so it reflects the people you actually carry.
Step 4: maximum horsepower, from the factor
The horsepower rating comes from 33 CFR 183.53, and it starts with a factor: the boat length in feet times the maximum transom width in feet. The transom width is not the beam: it is the width across the transom itself, or, on a boat with no full transom, the broadest beam in the aftermost quarter of the boat's length. A 16-foot boat with a 6-foot transom has a factor of 96. A 14-foot boat with a 3-foot transom has a factor of 42. The factor is rounded to 2 decimal places.
Up to a factor of 52.5, the horsepower comes from a table. A factor of 35 or less gives 3 hp. A factor of 36 to 39 gives 5 hp. A factor of 40 to 42 gives 7.5 hp. A factor of 43 to 45 gives 10 hp. A factor of 46 to 52 gives 15 hp. The table uses the factor rounded to the nearest whole number, so a factor of 36.4 takes the 36 to 39 band and a factor of 35.4 takes the 35-or-less band. A flat-bottom boat with hard chines and a factor of 52 or less drops one step: 7.5 hp becomes 5 hp, 15 hp becomes 10 hp, 5 hp becomes 3 hp. The table has no step below 3 hp, so a flat-bottom boat with a factor of 35 or less keeps the 3 hp rating, and the calculator says so rather than inventing a lower number.
Over a factor of 52.5, a formula applies, and the branch depends on the steering and the transom height. A boat with remote steering and a transom at least 20 inches high uses 2 times the factor minus 90. A boat with no remote steering, or a transom under 20 inches, uses 0.8 times the factor minus 25, or 0.5 times the factor minus 15 for a flat-bottom hard-chine boat. A factor of 96 with remote steering and a 20-inch transom gives 2 times 96 minus 90, which is 102 hp. The same factor with a tiller gives 0.8 times 96 minus 25, which is 51.8 hp. The same factor with a tiller and a flat bottom gives 0.5 times 96 minus 15, which is 33 hp. The regulation says a result that is not an exact multiple of 5 may be raised to the next exact multiple of 5, so 102 hp becomes 105 hp, 51.8 hp becomes 55 hp, and 33 hp becomes 35 hp. A result that is already a multiple of 5 stays where it is: a factor of 95 with remote steering gives exactly 100 hp, and a factor of 100 with a tiller gives exactly 55 hp.
One edge case deserves a note. The table covers factors to 52, by nearest whole number, and the formulas start over 52.5, so a factor of exactly 52.5 sits between the two: its nearest whole number is 53, which has no table band, and it is not over 52.5, so no formula applies. The calculator uses the top table value of 15 hp for a factor of exactly 52.5 and says so in the result and in the notes. A factor of 52.4 takes the table and a factor of 52.8 takes the formula, so the gap is a single point, and the calculator handles it openly rather than failing silently.
Worked examples
Every number below is the calculator's own output for the inputs shown, so you can check the tool against this page. The three examples match the three example buttons under the form.
Worked example 1: the 16-foot runabout
A 16-foot boat, 6-foot beam, 5.5-foot transom, outboard motor, tiller steering, 20-inch transom, V-hull, boat weight 500 pounds, maximum displacement 6,000 pounds, 150-pound passengers.
- Deck area: 16 ft times 6 ft equals 96 sq ft
- Persons: 96 divided by 15 equals 6.4, rounded down to 6 people
- People weight: 6 times 150 lb equals 900 lb
- Maximum weight capacity: (6,000 minus 500) divided by 5 equals 1,100 lb
- Motor, fuel, and gear budget: 1,100 minus 900 equals 200 lb
- Horsepower factor: 16 ft times 5.5 ft equals 88
- Horsepower: no remote steering, so 0.8 times 88 minus 25 equals 45.4 hp, raised to the next multiple of 5, which is 50 hp
- Result: up to 6 people, 900 lb of people, and a 50 hp motor
This is the clean case: every limit has room to spare. The people use 900 of the 1,100 pounds of weight capacity, leaving 200 pounds for a motor, a portable fuel tank, and gear. A 50 hp outboard with a portable tank and a cooler fits inside that budget on most 16-foot runabouts, but a heavy four-stroke motor, a full built-in tank, and a lot of gear can eat the 200 pounds fast, which is why the budget is printed on every result.
Worked example 2: the 14-foot jon boat
A 14-foot boat, 5-foot beam, 4.5-foot transom, outboard motor, tiller steering, 15-inch transom, flat bottom with hard chines, boat weight 300 pounds, maximum displacement 2,500 pounds, 150-pound passengers.
- Deck area: 14 ft times 5 ft equals 70 sq ft
- Persons: 70 divided by 15 equals 4.67, rounded down to 4 people
- People weight: 4 times 150 lb equals 600 lb
- Maximum weight capacity: (2,500 minus 300) divided by 5 equals 440 lb
- Motor, fuel, and gear budget: 440 minus 600 equals negative 160 lb
- Horsepower factor: 14 ft times 4.5 ft equals 63
- Horsepower: no remote steering and a flat-bottom hard-chine hull, so 0.5 times 63 minus 15 equals 16.5 hp, raised to the next multiple of 5, which is 20 hp
- Result: up to 4 people, 600 lb of people, and a 20 hp motor, with a warning that the people weigh 160 lb more than the weight capacity
This is the case the calculator exists for. The deck fits 4 people, but the hull's displacement only supports 440 pounds of total load, and 4 people at 150 pounds already weigh 600 pounds. The weight capacity governs: the honest load is 2 people at 150 pounds, 300 pounds, leaving 140 pounds for a small motor, fuel, and gear, or 3 light people with almost nothing else aboard. A jon boat this size is often used with 2 people and a trolling motor or a small outboard, and the numbers show why. The 20 hp rating is also a ceiling, not a target: a 20 hp motor on a 14-foot flat-bottom boat is a lot of power for the hull, and the flat-bottom branch of the formula is what keeps it at 20 rather than the 25 hp the V-hull branch would give.
Worked example 3: the 18-foot bowrider with heavier passengers
An 18-foot boat, 7.5-foot beam, 6.5-foot transom, outboard motor, remote steering, 20-inch transom, V-hull, boat weight 1,200 pounds, maximum displacement 9,000 pounds, 180-pound passengers.
- Deck area: 18 ft times 7.5 ft equals 135 sq ft
- Persons: 135 divided by 15 equals exactly 9 people
- People weight: 9 times 150 lb equals 1,350 lb
- At 180 lb a person: 1,350 divided by 180 equals 7.5, rounded down to 7 people
- Maximum weight capacity: (9,000 minus 1,200) divided by 5 equals 1,560 lb
- Motor, fuel, and gear budget: 1,560 minus 1,260 equals 300 lb, for 7 people at 180 lb each
- Horsepower factor: 18 ft times 6.5 ft equals 117
- Horsepower: remote steering and a 20 in transom, so 2 times 117 minus 90 equals 144 hp, raised to the next multiple of 5, which is 145 hp
- Result: up to 7 people at 180 lb each, and a 145 hp motor, with a warning that the weight limit cuts the count from 9 to 7
This is the passenger-weight case. The deck fits 9 people, and a buyer counting seats might expect 9, but the people weight only covers 7 adults at 180 pounds. The 300-pound budget then has to cover a motor in the 115 to 145 hp range, which alone can weigh 350 to 450 pounds on a modern four-stroke, plus fuel and gear. The honest reading is that 7 adults and a big motor is already a full boat, and 9 adults would need a lighter motor, less fuel, and almost no gear. The number of seats is not an indication of how many people a boat can carry: the weight is the limit that bites first.
What the capacity plate shows
The plate carries the heading U.S. Coast Guard Maximum Capacities on a yellow panel, and the lines on it depend on the boat's propulsion. Federal rules put the plate where the operator can clearly see it when getting underway, usually on the inside of the transom or next to the helm. The limits apply in good to moderate weather: in rough water, the safe load is lower than the plate.
| Boat | Lines on the plate |
|---|---|
| Outboard | Maximum persons, as a number and in pounds; maximum pounds of persons, motor, and gear; maximum horsepower, on some boats one figure with remote steering and one without |
| Inboard or sterndrive | Maximum persons, as a number and in pounds; maximum pounds of persons and gear |
| Rated for motors of 2 hp or less | Maximum persons, as a number and in pounds; maximum pounds of persons, motor, and gear; maximum horsepower |
| Oars or paddles | Maximum persons, as a number and in pounds; maximum pounds of persons and gear; This Boat Not Rated for Propulsion by Motor |
The persons line carries two numbers, and both bind: the count and the pounds. A plate that reads 6 persons, 900 pounds, means 6 people who together weigh no more than 900 pounds. Six 200-pound adults are 1,200 pounds, which breaks the pounds limit even though the count is right. The weight line covers everything the boat carries beyond its own weight: people, motor, fuel, gear, coolers, and bait wells. On an inboard boat the motor is part of the boat, so the weight line covers people and gear only, and there is no horsepower line, because the installed engine is the builder's choice, not the owner's.
The persons number on a real plate does not come from the rule of thumb. It comes from the builder's tests under 33 CFR 183.39 and 183.41: the persons capacity in pounds is the weight capacity less the motor, controls, battery, and fuel weights on an outboard boat, and for boats under 550 pounds of persons capacity it is also checked afloat, with weights added along one side until the boat reaches its maximum list or trim without water coming aboard. The count is then the pounds plus 32, divided by 141, rounded to the nearest whole number: 990 pounds allows 1,022 divided by 141, which is 7.25, so 7 people. Builders may mark fewer. That is why two boats of the same length and beam can carry different plates: the displacement, the hull shape, and the stability test decide, not the deck area alone.
The federal horsepower table
Table 183.53 in the regulation sets the horsepower rating for factors up to 52.5. The table uses the factor rounded to the nearest whole number. Over 52.5, the formulas in the section below the table apply.
| Factor, nearest whole number | Maximum horsepower |
|---|---|
| 0 to 35 | 3 hp |
| 36 to 39 | 5 hp |
| 40 to 42 | 7.5 hp |
| 43 to 45 | 10 hp |
| 46 to 52 | 15 hp |
For a factor over 52.5, the rating is a formula, raised to the next multiple of 5 when it is not already one. Remote steering with a transom of 20 inches or more gives 2 times the factor minus 90. No remote steering, or a transom under 20 inches, gives 0.8 times the factor minus 25, or 0.5 times the factor minus 15 for a flat-bottom hard-chine boat. The gap between the branches is large: at a factor of 96, remote steering allows 105 hp, a tiller allows 55 hp, and a tiller on a flat bottom allows 35 hp. The gap exists because steering and hull shape change what happens at speed: a tiller-steered boat at full power is harder to control than a wheel-steered one, and a flat bottom at speed can chine-walk and hook in turns.
There is also a performance-test route in 33 CFR 183.53 for small boats: a boat 13 feet or shorter with remote wheel steering, a minimum transom height, and room for no more than two people may be rated by a test run instead of the computation, up to 40 hp. The test runs the boat through a course at speed with a driver and a passenger, and the rating comes from how the boat behaves. This calculator uses the computation method only, because the performance test needs a boat, a course, and a test crew, and a web page cannot run it. If your small boat carries a plate rating above the computed figure, the performance test is the likely reason.
Persons capacity by boat size
The table below runs the rule of thumb over common small-boat sizes. Every row is length times beam divided by 15, rounded down, with the people weight at 150 pounds each. Use it to sanity-check a boat at a glance, and use the calculator for the full answer with your real passenger weight and your displacement figures.
| Length | Beam | Deck area | Length times beam divided by 15 | Max persons | People weight |
|---|---|---|---|---|---|
| 12 ft | 4 ft | 48 sq ft | 3.2 | 3 | 450 lb |
| 14 ft | 5 ft | 70 sq ft | 4.67 | 4 | 600 lb |
| 16 ft | 6 ft | 96 sq ft | 6.4 | 6 | 900 lb |
| 18 ft | 6 ft | 108 sq ft | 7.2 | 7 | 1,050 lb |
| 18 ft | 7 ft | 126 sq ft | 8.4 | 8 | 1,200 lb |
| 19 ft | 8 ft | 152 sq ft | 10.13 | 10 | 1,500 lb |
Notice how the rounding bites: a 14-foot boat with a 5-foot beam gives 4.67, which is 4 people, not 5, and an 18-foot boat with a 7-foot beam gives 8.4, which is 8, not 9. Rounding down is the safe direction for a maximum, and it is the direction this calculator takes on every count and every weight capacity. The horsepower rating is the one figure that rounds up, and only because the regulation itself says the formula result may be raised to the next multiple of 5.
What this calculator does differently
Several boat capacity calculators exist online, and most of them run the rule of thumb and stop there, or run a simplified horsepower estimate. This one runs the full federal method, and it is honest about the parts other tools skip. The horsepower rating uses the real Table 183.53 with the nearest-whole-number rule, the flat-bottom step-down, and the three formula branches, including the remote-steering transom-height condition that decides between them. It handles the factor of exactly 52.5 openly instead of failing or guessing. It raises formula results to the next multiple of 5, as 33 CFR 183.53(a)(3) provides, and it says so in the working.
The weight capacity runs the regulation's own formulas for all three propulsion types, including both branches of the inboard formula with the greater value governing, and the displacement-only branch when no machinery weight is entered. It rounds every capacity down, because a capacity must not exceed its computed value. The people count adjusts for your passengers' real average weight, which most calculators ignore even though it is the adjustment that most often changes the answer. And the motor, fuel, and gear budget turns the abstract capacity into the number you actually load against: what is left after the people are aboard. The worked examples above show the budget going negative on a small jon boat, which is the finding that matters most on that boat, and it is the finding a persons-only calculator would never show.
The calculator is also strict about scope. It refuses boats 20 feet or longer rather than extrapolating formulas that do not cover them. It refuses a transom wider than the beam, a displacement smaller than the boat weight, and numbers it cannot parse, with a message that says what is wrong. It never invents a displacement or a boat weight: if you do not know them, it says the weight capacity needs them, and gives you the answers it can stand behind. A calculator that guesses at a safety limit is worse than one that admits what it does not know.
Use cases
Checking a used boat before you buy it. A used boat with no plate, or a plate you cannot read, is a common sight at a marina or in a driveway listing. Measure the length, the beam, and the transom width, ask the seller for the boat weight and displacement from the manual, and run the calculator. If the seller's claims about capacity are well above the calculator's numbers, ask for the plate or the builder's specifications. If the boat is 20 feet or longer, the federal formulas do not apply, and the builder's figures are the only honest source.
Loading the family for a day on the water. Count the people, weigh the group honestly, and enter the real average. A boat rated for 6 people at 150 pounds each advises 4 at 200 pounds each, and the gear budget shows what is left for the cooler, the fuel, and the tackle. Run the numbers before you leave the dock, not after the boat is loaded, because taking people off at the ramp is easier than taking them off on the water.
Choosing an outboard motor. The horsepower rating is the ceiling for the motor, not a recommendation. A motor at the rating gives the boat its designed top speed with its rated load. A motor above the rating changes the handling, stresses the transom, can be illegal to operate in many states, and can affect insurance. A motor well below the rating is safe but slow with a full load. Use the rating to size the motor, then check the motor's weight against the gear budget, because a heavy motor eats the same budget as the people.
Restoring or rebuilding an old boat. A restoration often changes the boat weight: new decks, new fuel tanks, and added gear all add pounds, and added weight comes straight off the weight capacity. Enter the rebuilt weight and the original displacement to see the new capacity. If the restoration added a lot of weight, the capacity may be much lower than the original plate said, and the plate's numbers no longer describe the boat.
Teaching a boating safety course. The rule of thumb is on every boating exam, and the calculator shows the working step by step, so students can check the arithmetic and see where each number comes from. The worked examples above cover the three shapes the answer takes, and the horsepower table and the inboard two-branch formula give instructors the regulation's own text to point at. Pair it with our Life Jacket Size Finder for the safety gear lesson, and our Kayak Size Finder, Canoe Size Finder, and Paddle Board Size Finder for the paddlecraft that the federal capacity rules do not cover.
Planning the running costs. Once the capacity is settled, the trip still needs fuel, and the boat still needs keeping. Our Boat Fuel Cost and Range Calculator works out fuel cost and range for the trip, our Boat Ownership Cost Calculator totals storage, insurance, maintenance, and fuel for the year, our Boat Registration Cost Calculator estimates the registration bill, and our Anchor Size and Rode Calculator sizes the ground tackle for the boat. For the water itself, our Tide Height Calculator estimates the tide at your launch time, and for the run home our Sailboat Hull Speed Calculator and Propeller Slip Calculator cover speed and propeller efficiency.
Pontoon boats and boats 20 feet or longer
The federal capacity rules cover monohull boats under 20 feet. A pontoon boat is not a monohull: the regulation names it as an example of a boat that is not one. The rule of thumb does not fit pontoons well, because a pontoon's capacity comes from the buoyancy of its tubes, not from its deck area. A 20-foot pontoon 8 feet 6 inches wide would give 11 people by the rule of thumb, where the builder rates the same boat for 9. For a pontoon, use the builder's capacity label or specifications, and do not use this calculator's people count.
Boats 20 feet or longer are outside the federal capacity rules too. The builder still publishes capacities, usually on a label near the helm or in the owner's manual, and the Coast Guard's stability and flotation rules still apply to the builder, but there is no federal formula that turns length and beam into a people count for them. This calculator refuses lengths of 20 feet or more rather than extrapolating. Sailboats, canoes, kayaks, and inflatable boats are also outside the rules: sailboats carry ballast that changes the stability picture, canoes and kayaks are rated by the maker, inflatables are rated by the maker, and personal watercraft follow the manufacturer's manual and the warning decal on the craft. If your boat is in one of these groups, the maker's figures govern, and the rule of thumb is not a substitute.
Loading safely: weather, weight, and balance
The capacity numbers assume good weather, seated passengers, and weight spread evenly. Real trips break all three assumptions, and each break cuts the safe load. In chop, wind, or rough water, carry fewer people and less gear than the maximum: the plate's limits apply in good to moderate weather, and a boat that is fine on a calm lake can take water over the side in a chop with the same load. Standing passengers raise the center of gravity and make the boat less stable than the same weight seated, which is why the rule of thumb assumes seated people. Weight piled on one side lists the boat and cuts freeboard on the low side, so spread coolers, fuel, and gear across the boat and keep heavy items low and near the centerline.
Fuel and water are heavy in ways people forget. A portable fuel tank holds 6 gallons at about 6 pounds a gallon, so a full tank is about 36 pounds plus the tank itself. A cooler full of ice and drinks can weigh 50 pounds or more. Fishing gear, anchors, and bait wells add up fast. Count them in the gear budget, and weigh the big items if you are near the limit. Children count as people for the count, even though they weigh less: the count limit and the pounds limit both bind, so a boat rated for 6 people cannot carry 8 small children, and a boat rated for 900 pounds of people cannot carry 6 adults who together weigh 1,200 pounds.
Overloading is a leading factor in small-boat accidents, which is why the plate exists. An overloaded boat sits lower, takes water over the side sooner, handles worse, and is harder to recover from a mistake. The margin between the rated load and the sinking load is the safety factor in the formulas: one-fifth of the displacement difference for an outboard boat, which means the boat can carry about five times its rated load before the water reaches the point of coming aboard in calm water. That margin is not spare capacity to spend. It is the reserve that covers waves, movement, and the unexpected, and spending it leaves nothing for the day the weather turns.
On the legal side, the federal capacity rules bind manufacturers, not operators: the regulation tells the builder what the plate must say. But many states prohibit carrying more people or weight than the plate allows, or fitting a motor above the horsepower limit, and exceeding the plate can affect insurance coverage after an accident. The plate is the standard of care a court and an insurer will look at. Staying inside it is both the safe choice and the legally safe one. If your boat has no plate, keep the calculator's result with the boat's papers, and treat it as the limit until the builder gives you a better number.
Sources
All formulas were re-verified against the primary sources on 20 November 2026. The regulation governs every figure on this page; where a secondary source disagreed with the regulation, the regulation was followed and the disagreement is noted in the page register.
- 33 CFR 183.53, Horsepower capacity, Cornell Law Institute: the factor, Table 183.53, the three formula branches, the raise to the next multiple of 5, the flat-bottom reduction, and the performance-test route.
- 33 CFR 183.35, Maximum weight capacity: Outboard boats, Cornell Law Institute: one-fifth of the difference between maximum displacement and boat weight.
- 33 CFR 183.33, Maximum weight capacity: Inboard and inboard-outdrive boats, Cornell Law Institute: the greater of the machinery branch and the displacement branch.
- 33 CFR Part 183, Boats and Associated Equipment, govinfo: 183.31 applicability, 183.37 manual and small-motor weight capacity, 183.39 and 183.41 persons capacity and the 141-pound conversion.
- Calculating Your Boat's Capacity, Boat Ed: the Coast Guard rule of thumb, length times width divided by 15, for boats under 20 feet without a plate, assuming 150-pound people in good weather, with the 18-foot by 6-foot example giving 7 people.
- Boat Capacity, Rules and Weight Calculation, BOATERexam: the rule of thumb, the 150-pound manufacturer assumption, and the guidance to reduce the count for heavier passengers and heavy equipment.
Frequently asked questions
How many people can a boat hold?
Read the capacity plate first: it states the maximum persons as a number and in pounds, and both limits bind. For a boat without a plate, the Coast Guard rule of thumb is length times beam divided by 15, in feet, assuming 150-pound people in good weather. A 16-foot boat 6 feet wide gives 96 divided by 15, which is 6.4, rounded down to 6 people, or 900 pounds. If your passengers average more than 150 pounds, divide the people weight by the real average: 900 pounds allows 4 people at 200 pounds each. The rule applies to monohull boats under 20 feet only.
What does the capacity plate on a boat show?
The yellow plate under the heading U.S. Coast Guard Maximum Capacities shows the maximum persons as a number and in pounds, the maximum total weight of persons, motor, and gear on an outboard boat, or persons and gear on an inboard boat, and, on an outboard boat, the maximum horsepower. Boats rated for manual propulsion or motors of 2 hp or less show the 2 hp limit instead. Federal rules put the plate where the operator can clearly see it when getting underway, usually on the inside of the transom or next to the helm, and the limits apply in good to moderate weather.
How is maximum horsepower calculated for a boat?
Under 33 CFR 183.53, the builder computes a factor by multiplying the boat length by the maximum transom width, both in feet. Up to a factor of 52.5, the horsepower comes from a table: 3 hp to a factor of 35, 5 hp to 39, 7.5 hp to 42, 10 hp to 45, and 15 hp to 52. Over 52.5, a formula applies: 2 times the factor minus 90 with remote steering and a transom of 20 inches or more, 0.8 times the factor minus 25 otherwise, or 0.5 times the factor minus 15 for a flat-bottom hard-chine boat, raised to the next multiple of 5. A factor of 96 gives 105 hp, 55 hp, or 35 hp on the three branches.
How is a boat's maximum weight capacity calculated?
From the boat's maximum displacement, the weight of the water the hull displaces at maximum level immersion. For an outboard boat, 33 CFR 183.35 sets the capacity at one-fifth of the difference between maximum displacement and boat weight: 5,000 pounds of displacement and 500 pounds of boat weight gives 900 pounds. For an inboard boat, 33 CFR 183.33 takes the greater of two formulas, one using the machinery weight and one dividing the same difference by 7. For a boat rated for manual propulsion or a motor of 2 hp or less, 33 CFR 183.37 uses three-tenths of the difference. A capacity must not exceed its computed value, so the figure rounds down.
What size boat needs a capacity plate?
Federal rules require a capacity plate on monohull boats less than 20 feet long that are designed for motor propulsion, except sailboats, canoes, kayaks, and inflatable boats. Longer boats, pontoon boats, sailboats, canoes, kayaks, inflatables, and personal watercraft are outside the federal capacity rules and follow the builder's or maker's figures instead. If your boat is under 20 feet and has no plate, check with the manufacturer, find a sister boat of the same model, or use the Coast Guard rule of thumb as an estimate.
Does the rule of thumb work for pontoon boats?
No. A pontoon boat is not a monohull, and its capacity comes from the buoyancy of its tubes, not from its deck area. The rule of thumb overstates it: a 20-foot pontoon 8 feet 6 inches wide gives 11 people by length times beam divided by 15, where the builder rates the same boat for 9. Pontoon builders publish their own capacities on a label or in the specifications, and those figures govern. This calculator's people count applies to monohull boats under 20 feet only.
Is it illegal to exceed a boat's capacity?
The federal capacity rules bind manufacturers, not operators, so exceeding the plate is not a federal violation for the owner. But many states prohibit carrying more people or weight than the plate allows, or fitting a motor above its horsepower limit, and exceeding the limits can affect insurance coverage after an accident. The plate is the standard of care a court and an insurer will look at. Staying inside the plate is both the safe choice and the legally safe one.
What if my boat has no capacity plate?
Check with the manufacturer first, or find a sister boat of the same model and read its plate. A naval architect or marine engineer can work the capacity out from the hull. If none of those is available, the Coast Guard rule of thumb gives an estimate: length times beam divided by 15 for people, and the formulas in 33 CFR 183 for weight and horsepower, which is what this calculator runs. Keep the estimate with the boat's papers and treat it as the limit. If the boat later gets a plate, or the builder gives you a figure, the plate governs and the estimate is set aside.