Skip to content

Propeller Slip Calculator

Slip mode compares your measured speed with the theoretical speed from your pitch, RPM, and gear ratio. Pitch mode works backwards from a target speed and slip to a pitch.

The normal slip band depends on the hull: performance 5 to 10%, runabout 10 to 15%, cruiser 15 to 25%, displacement 25 to 40%.

Engine revolutions per minute at the test condition, 500 to 8000. Slip is usually measured at wide-open throttle.

Engine revolutions per propeller revolution, 1.00 to 3.00. Enter 1.85 for a 1.85:1 gearcase. Confirm the ratio on the gearcase stamp or in the service manual.

The pitch stamped on the propeller hub, 5 to 40 inches. On a prop marked 14 x 19, the pitch is 19.

GPS speed at the same RPM, above 0 and up to 150. Run both directions on calm water and average the two speeds.

The unit for the speed you enter. The math runs in mph and converts back for display.

The formula: theoretical speed (mph) = pitch (inches) x engine RPM / (gear ratio x 1056). Slip = (theoretical speed - actual speed) / theoretical speed x 100. The 1056 converts inches per minute to miles per hour: 63,360 inches in a mile divided by 60 minutes in an hour.

Your propeller slip

How the numbers were worked out

      This tool estimates propeller slip and suggests a propeller pitch from the numbers you enter, for general guidance only. It does not account for propeller diameter, blade area, cup, rake, hull shape, load, or engine height, and it is not a substitute for a sea trial or a propeller shop's advice. Confirm the gear ratio on your gearcase and the pitch on your propeller before acting on the result.
      Propeller slip is the shortfall between the theoretical speed from your pitch, RPM, and gear ratio and your actual GPS speed, as a percentage of the theoretical speed. A runabout should slip 10 to 15%: at 19 inches of pitch, 5,500 RPM, and a 1.85:1 gear ratio, the theoretical speed is 53.49 mph, so 46 mph on GPS is 14.0% slip, inside the band. Enter your pitch, RPM, gear ratio, and speed above for your slip, the verdict for your hull type, and the speed at each slip level, or switch to pitch mode for a suggested propeller pitch.

      Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.

      How to use the Propeller Slip Calculator

      A propeller is a screw that turns in water instead of wood. Its pitch is the distance it would travel forward in one revolution if water were solid: a propeller with 19 inches of pitch would move 19 inches per turn. Water gives way, so the boat never gets the full pitch distance. The shortfall, expressed as a percentage of the theoretical distance, is propeller slip. This calculator works out your slip from four numbers you already have or can measure in one test run: propeller pitch, engine RPM, gear ratio, and actual speed. It also runs backwards: give it a target speed, an RPM, a gear ratio, and a slip figure, and it suggests the propeller pitch that gets you there.

      Slip is the fastest diagnostic a boater has. A slip figure inside the normal band for your hull type means the propeller and the setup are doing their job. A figure above the band points at a real problem: a damaged propeller, a fouled hull, too much load, the wrong trim, or a motor mounted too high and ventilating. A figure below the band, or a negative figure, usually means one of your readings is off. The calculator reads the result for you, in plain language, against the band for your hull type, and it prints every step of the working so you can check the arithmetic yourself.

      To find your slip, follow these steps:

      1. Choose what to work out. Leave the mode on "Find my propeller slip" to measure slip from a test run. Switch to "Suggest a propeller pitch" to work backwards from a target speed.
      2. Pick your hull type. The normal slip band depends on the hull: a performance boat runs 5 to 10%, a runabout 10 to 15%, a cruiser 15 to 25%, and a displacement hull 25 to 40%. The calculator judges your result against the band for the hull you pick, so pick the closest match.
      3. Enter the engine RPM. This is the engine speed during the test run, from the tachometer, 500 to 8,000 RPM. Slip is usually measured at wide-open throttle, with the boat on plane and the speed steady. If you measure at cruise RPM instead, the calculator still works, but the reading is a cruise reading, and it warns you when the RPM is below 4,000.
      4. Enter the gear ratio. This is the number of engine revolutions per propeller revolution, 1.00 to 3.00. Enter 1.85 for a 1.85:1 gearcase. The ratio is printed on the gearcase stamp or in the service manual. The preset buttons fill in the common Mercury ratios (1.62:1, 1.75:1, 2.00:1) and Yamaha ratios (1.75:1, 2.00:1, 2.33:1), but always confirm the ratio for your own engine: the wrong ratio throws the whole answer off.
      5. Enter the propeller pitch. The pitch is stamped on the propeller hub, 5 to 40 inches. On a propeller marked 14 x 19, the first number is the diameter (14 inches) and the second is the pitch (19 inches). Enter the pitch, not the diameter. If the propeller has been repaired or re-pitched, the stamped number may no longer match the true pitch, and a propeller shop can measure it.
      6. Enter the actual speed. This is the GPS speed at the same RPM, above 0 and up to 150 in the unit you pick. Use speed over ground from a GPS, not a paddle-wheel or pitot speedometer. Run the same stretch in both directions on calm water and average the two speeds, so current and wind roughly cancel out.
      7. Pick the speed unit. Miles per hour, knots, or kilometers per hour. The math runs in mph and converts back for display, so the slip percentage is the same whichever unit you use.

      To suggest a pitch instead, switch the mode to "Suggest a propeller pitch" and enter the target speed, the RPM you want the engine to reach at full throttle, the gear ratio, and the slip you want to aim for. Leave the target slip blank and the calculator uses the middle of the normal band for your hull type: 7.5% for a performance boat, 12.5% for a runabout, 20% for a cruiser, and 32.5% for a displacement hull. The result gives the exact pitch, the nearest whole-inch stock pitch, and the speed each neighboring pitch would give at the same RPM and slip, so you can see what one inch up or down costs you.

      The tool updates as you type, so you can try different numbers quickly. Try the example buttons under the form: the first is a runabout with a 19-inch pitch at 5,500 RPM and a 1.85:1 gear ratio running 46 mph, which slips 14.0% and sits inside the normal band; the second is the same kind of boat with a 21-inch pitch at 6,000 RPM running 52 mph, which slips 23.7% and is a problem to investigate; the third suggests a pitch for 55 mph at 5,800 RPM and 12% slip; and the fourth is a knots example from a published Yamaha sea trial, a 22-inch pitch at 6,100 RPM and a 2.00:1 ratio running 50.2 knots, which slips 9.1%.

      Read the full result, not just the headline. The headline leads with your slip percentage and its verdict against the band. The cards show the theoretical speed, the actual speed, the propeller shaft speed, the advance per revolution, and the speed lost to slip. The table shows the speed the same setup would run at 5, 10, 15, 20, and 25% slip. The guidance explains the result in plain language, the warnings flag the readings that need a second look, the steps print the full working so you can check every figure, and the notes explain what slip is and is not.

      How it works

      The calculator runs three calculations in order: the propeller shaft speed, the theoretical speed, and the slip percentage. Each one uses the result of the one before it, and the steps section on the page prints all three so you can check them against your own arithmetic. Pitch mode runs the same formula backwards: it works out the theoretical speed needed for your target, then the pitch that produces it.

      Step 1: propeller shaft speed

      The gear ratio sits between the engine and the propeller. A 1.85:1 ratio means the engine turns 1.85 times for each propeller revolution, so the propeller turns slower than the engine. Divide the engine RPM by the gear ratio to get the propeller shaft speed. At 5,500 engine RPM and a 1.85:1 ratio, the propeller turns at 5,500 / 1.85 = 2,973.0 RPM. At 6,100 RPM and a 2.00:1 ratio, it turns at 3,050 RPM. The shaft speed is the number the pitch acts on: each propeller revolution advances the boat by one pitch length in theory, so the theoretical speed is the pitch times the shaft speed, converted to miles per hour.

      Step 2: theoretical speed

      The theoretical speed is the speed the boat would reach if the propeller advanced exactly one pitch length per revolution, with no slip at all. The formula is: theoretical speed (mph) = pitch (inches) x engine RPM / (gear ratio x 1056). The 1056 is a unit conversion, not a fudge factor: there are 63,360 inches in a mile, and 60 minutes in an hour, so 63,360 / 60 = 1,056 converts inches per minute to miles per hour. With a 19-inch pitch at 5,500 RPM and a 1.85:1 ratio, the theoretical speed is 19 x 5,500 / (1.85 x 1056) = 104,500 / 1,953.6 = 53.49 mph. The same formula in knots divides by 1,215 instead of 1,056, because a knot is 1.15078 mph and 1,056 x 1.15078 = 1,215.22, which rounds to 1,215.

      Step 3: slip percentage

      Slip is the shortfall between the theoretical speed and the actual speed, as a percentage of the theoretical speed: slip (%) = (theoretical speed - actual speed) / theoretical speed x 100. Dividing by the theoretical speed is deliberate: it asks what fraction of the ideal, no-slip advance was given up to the water, which makes slip comparable across different boats, pitches, and gear ratios. A 15% figure means the same thing whether the theoretical speed is 20 mph or 60 mph. In the default example the theoretical speed is 53.49 mph and the actual speed is 46 mph, so the slip is (53.49 - 46) / 53.49 x 100 = 14.0%. The boat loses 7.49 mph to slip, and it advances 16.34 inches per propeller revolution instead of the 19 inches the pitch promises.

      One source of confusion is worth clearing up. A few older web pages divide the speed difference by the actual speed instead of the theoretical speed. That gives a larger number for the same run and it is not the standard definition: Mercury Marine, Yamaha sea-trial practice, OmniCalculator, and the propeller guides all divide by the theoretical speed. This calculator follows the standard. If a figure you found elsewhere looks higher than this calculator gives for the same run, check which denominator it used.

      Worked example 1: the defaults, a runabout in the normal band

      Pitch 19 inches, engine RPM 5,500, gear ratio 1.85:1, actual speed 46 mph, runabout.

      • Propeller shaft speed: 5,500 RPM / 1.85 = 2,973.0 RPM
      • Theoretical speed: 19 in x 5,500 RPM / (1.85 x 1056) = 53.49 mph
      • Slip: (53.49 - 46) / 53.49 x 100 = 14.0%
      • Speed lost to slip: 53.49 - 46 = 7.49 mph
      • Advance per revolution: 19 in x 46 / 53.49 = 16.34 in
      • Verdict: 14.0% sits inside the normal 10-15% band for a runabout

      The same setup at other slip levels would run: 50.8 mph at 5% slip, 48.1 mph at 10%, 45.5 mph at 15%, 42.8 mph at 20%, and 40.1 mph at 25%. Each extra 5 points of slip costs about 2.7 mph at this theoretical speed, which is why a slipping propeller shows up first as a top speed that is lower than it should be.

      Worked example 2: a runabout slipping too much

      Pitch 19 inches, engine RPM 6,000, gear ratio 2.00:1, actual speed 45 mph, runabout. This is the worked example from Dunnrite Propellers, a New Zealand propeller shop, recomputed exactly.

      • Propeller shaft speed: 6,000 RPM / 2.00 = 3,000 RPM
      • Theoretical speed: 19 in x 6,000 RPM / (2.00 x 1056) = 53.98 mph
      • Slip: (53.98 - 45) / 53.98 x 100 = 16.6%
      • Speed lost to slip: 53.98 - 45 = 8.98 mph
      • Advance per revolution: 19 in x 45 / 53.98 = 15.84 in
      • Verdict: 16.6% sits above the normal 10-15% band for a runabout, so it is worth investigating

      Dunnrite prints the slip as 16.62% because it rounds the theoretical speed down to 53.97 mph first; the exact figure is 53.98 mph and the slip is 16.6% at one decimal place. The difference is rounding, not method. Either way the verdict is the same: a runabout slipping 16.6% is above its band, and the owner should check the propeller, the hull, and the load before anything else.

      Worked example 3: knots, from a Yamaha sea trial

      Pitch 22 inches, engine RPM 6,100, gear ratio 2.00:1, actual speed 50.2 knots, performance boat. These are the figures from Yamaha's published test of a Skeeter ZX 190, as worked through by PropBench.

      • Propeller shaft speed: 6,100 RPM / 2.00 = 3,050 RPM
      • Actual speed: 50.2 knots x 1.15078 = 57.77 mph
      • Theoretical speed: 22 in x 6,100 RPM / (2.00 x 1056) = 63.54 mph, which is 55.22 knots
      • Slip: (63.54 - 57.77) / 63.54 x 100 = 9.1%
      • Speed lost to slip: 63.54 - 57.77 = 5.77 mph
      • Advance per revolution: 22 in x 57.77 / 63.54 = 20.00 in
      • Verdict: 9.1% sits inside the normal 5-10% band for a performance boat

      PropBench rounds the answer to 9%, using the knots shortcut of dividing by 1,215: 3,050 x 22 / 1,215 = 55.2 knots with no slip, and 1 - 50.2 / 55.2 = 9%. The shortcut and the exact conversion agree to the nearest whole percent. The calculator uses the exact conversion (1 knot = 1.15078 mph) and reports 9.1%.

      Worked example 4: pitch mode, working backwards from a target

      Target speed 55 mph, engine RPM 5,800, gear ratio 1.75:1, target slip 12%, runabout.

      • No-slip speed needed: 55 mph / (1 - 0.12) = 62.50 mph
      • Suggested pitch: 62.50 mph x 1.75 x 1056 / 5,800 RPM = 19.91 in
      • Nearest stock pitch: 20 in, giving 20 in x 5,800 RPM x (1 - 0.12) / (1.75 x 1056) = 55.24 mph
      • One inch less (19 in) gives 52.48 mph, and one inch more (21 in) gives 58.00 mph, at the same RPM and slip

      The 20-inch propeller is the pick: it lands 0.24 mph above the target at the assumed slip, while the 19-inch falls 2.52 mph short and the 21-inch overshoots by 3.00 mph. But the answer depends on the slip assumption. If the boat actually slips 15% with the 20-inch propeller instead of 12%, the speed is 20 x 5,800 x 0.85 / (1.75 x 1056) = 53.36 mph, below the target. That is why the suggested pitch is a starting point for a sea trial, not a purchase order: fit the nearest pitch, run the boat, measure the real slip, and adjust from there.

      Worked example 5: a displacement hull, where high slip is normal

      Pitch 18 inches, engine RPM 2,400, gear ratio 2.50:1, actual speed 10.5 mph, displacement hull.

      • Propeller shaft speed: 2,400 RPM / 2.50 = 960 RPM
      • Theoretical speed: 18 in x 2,400 RPM / (2.50 x 1056) = 16.36 mph
      • Slip: (16.36 - 10.5) / 16.36 x 100 = 35.8%
      • Speed lost to slip: 16.36 - 10.5 = 5.86 mph
      • Advance per revolution: 18 in x 10.5 / 16.36 = 11.55 in
      • Verdict: 35.8% sits inside the normal 25-40% band for a displacement hull

      A runabout slipping 35.8% would have a serious problem. A displacement hull slipping 35.8% is working normally: the hull pushes a bow wave it can never climb over, the propeller works hard at low speed, and a large share of the pitch advance is lost to the water. This is why the calculator asks for the hull type before judging the number. The same slip percentage means opposite things on different hulls.

      What is a normal propeller slip?

      There is no single normal slip figure, because slip depends on how fast the boat goes and how hard the propeller has to push. A light performance boat on plane slips little. A heavy displacement hull pushing a bow wave slips a lot. Mercury Marine, the largest outboard maker, gives the broadest guidance: in its article "Prop Bite: Understanding Propeller Slip", Mercury says calculated slip within the range of 5% to 25% is typical and acceptable, and slip greater than 25% likely means an issue with the propeller. That 5 to 25% band covers most outboard and sterndrive boats, but it is wide, and a useful reading needs the hull type. The bands this calculator uses break Mercury's broad range down by hull:

      Hull typeNormal slip bandWhat it covers
      Performance boat5-10%Light, fast planing hulls: bass boats, flats boats, race vee-bottoms
      Runabout10-15%Typical recreational planing boats, lightly to moderately loaded
      Cruiser15-25%Heavier planing hulls, more wetted area, cruising load with fuel and gear
      Displacement hull25-40%Workboats, trawlers, sailboats under power, heavy hulls below hull speed

      These bands line up with the published sea-trial data. PropBench, which recomputed the full-throttle slip of published sea trials that report all four figures (engine RPM, gear ratio, pitch, and measured speed), found the following medians in its guide updated 5 November 2026:

      Drive and hullMedian slipMiddle half of trialsMedian top speed
      Outboard9%6-11%46 knots
      Sterndrive11%9-13%41 knots
      Shaft, planing hull20%17-24%30 knots
      Shaft, displacement or semi-displacement hull38%28-44%9 knots

      The pattern is clear: the slower the boat, the more the propeller slips. Outboards at 46 knots slip about 9%; displacement boats at 9 knots slip about 38%. The calculator's bands sit on top of this pattern: a runabout at 10-15% matches the outboard and sterndrive medians, a cruiser at 15-25% matches the shaft planing median of 20%, and a displacement hull at 25-40% brackets the 38% median. The old propeller-shop rule of thumb, printed by Dunnrite Propellers, tells the same story in speed terms: planing race boats around 10%, high-speed planing boats around 20%, lightweight cruisers around 24%, heavy powerboats around 26%, and auxiliary sailboats and barges around 45%.

      Two thresholds matter most in practice. On a planing hull, slip over 20% signals a problem worth investigating: the boat is giving up a fifth of its pitch advance, and something is usually wrong. Across all hull types, Mercury's 25% line is the point where the propeller itself is the prime suspect: damaged, wrong for the boat and engine, or ventilating because the motor is mounted too high. The calculator applies both: it warns on slip over 20% for performance boats and runabouts, and it warns on slip over 25% for every planing hull, quoting Mercury's guidance. For a displacement hull, the warning line is 40%, the top of its band.

      Slip also changes with speed on the same boat. At low speed, before the hull climbs onto plane, the propeller works against a hull that is pushing a large bow wave, and slip is high. As the boat planes and the wetted area shrinks, slip falls. That is why slip is measured at wide-open throttle, where the boat is fully on plane and the reading is comparable between boats and between test days. A slip figure measured at 3,500 RPM on a boat that planes at 4,000 RPM is not the same measurement as a wide-open-throttle figure, and the calculator warns you when the RPM is below 4,000 for exactly that reason.

      What high slip means

      High slip means the propeller is turning without moving the boat as far as it should. The propeller is not necessarily at fault: slip measures the whole setup, hull and load included. Work through the causes in order of how easy they are to check, and re-measure after each fix, because two small problems can add up to one large slip figure.

      The propeller is damaged or worn

      A bent, chipped, or worn blade gets a poorer hold on the water. Small pits in the blades are a sign of cavitation: the water boils on the blade surface where the pressure drops, the vapor bubbles collapse and pit the metal, and the damaged blade slips more. A propeller that has hit the bottom may look straight and still be out of true. Have a propeller shop check the blades, measure the true pitch, and repair or replace the propeller. After a repair or a re-pitch, the stamped pitch may no longer match the true pitch, so a shop measurement is the only reliable figure.

      The propeller is ventilating

      Ventilation is air reaching the propeller, usually because the outboard or outdrive is mounted too high on the transom, or because the engine is trimmed too far out. The engine revs up but the boat does not speed up, and the slip figure jumps. Ventilation often shows up in turns or in rough water first. Trim in and see whether the slip falls; if it does, have a shop check the engine height and the plate above the propeller. Mercury names ventilation as one of the three likely causes when slip passes 25%, alongside a damaged propeller and a propeller wildly wrong for the boat and engine.

      The hub has spun

      Outboard and sterndrive propellers have a rubber or plastic insert in the hub that absorbs shock. When the insert wears, the shaft can turn inside the propeller: the engine revs, the propeller turns more slowly than the shaft, and the slip figure climbs. PropBench gives a simple dockside test: draw a straight line from the end of the propeller shaft onto the hub, run at full throttle for a while, and check whether the two parts of the line still meet. If they do not, the insert has lost its grip and the hub needs re-hubbing or the propeller needs replacing.

      The hull is fouled or the boat is overloaded

      Growth on the hull and propeller, or a heavy load, costs speed at the same RPM, and the lost speed shows up as slip. A fouled bottom is the most common cause of a slip figure that has crept up over a season with no other change. Clean the hull and propeller, empty the boat to a normal load, and measure again. Fuel, water, gear, and passengers all count: a boat tested with a full fuel tank, a full water tank, and four people aboard will slip more than the same boat tested light, and the difference can be several percentage points.

      The propeller is too small for the boat

      A propeller with too little diameter or blade area slips more, because it cannot get enough grip on the water to push the hull. This is a sizing problem rather than a damage problem: the pitch may be right and the diameter wrong. Diameter is the first number stamped on the hub (14 in a 14 x 19 marking). If the slip stays high after the propeller, hull, and load have been checked, talk to a propeller shop about diameter and blade area, not just pitch. Switching from a three-blade to a four-blade propeller of the same pitch adds blade area and usually lowers wide-open-throttle RPM by 50 to 100, according to Mercury's propeller manual.

      The test conditions were bad

      Rough water, a headwind, and a strong current all raise the measured slip, because the GPS speed falls while the RPM stays the same. A slip figure measured on a rough day is not comparable with one measured on a calm day. Always test on calm water, run both directions, and average the two speeds. If the two directions differ by more than a couple of miles per hour, current or wind is doing most of the work, and the average is still the honest figure to use.

      What low or negative slip means

      Slip below the normal band is less common than high slip, and it usually means a figure is off rather than a great setup. The first thing to check is the test itself: a current or a tailwind raises the speed over ground, which lowers the calculated slip, and a single-direction run can easily produce a figure several points too low. Run both directions and average. The second thing to check is the tachometer: if it reads high, the theoretical speed comes out high and the slip comes out low. Check it against a handheld tachometer. The third is the gear ratio: an engine with a 1.85:1 gearcase entered as 2.00:1 gives a theoretical speed about 8% too low, which takes roughly 7 points off the slip, so a boat truly slipping 14% would read about 7%. Confirm the ratio on the gearcase stamp.

      Very low slip, under 5%, can also mean the propeller is over-pitched and the engine is lugging: the propeller is too big for the engine, the engine cannot reach its rated wide-open-throttle RPM range, and the boat feels sluggish out of the hole even though the slip number looks good. The calculator warns on slip under 5% for exactly this reason. Check the wide-open-throttle RPM against the engine maker's recommended range: if the engine falls short of the range, drop one or two inches of pitch and retest.

      A cupped propeller also slips less than a plain one. Cupping bends the trailing edge of the blades slightly, which gives the propeller a better hold on the water. A cupped propeller can read a point or two lower than an uncupped propeller of the same pitch, which is a real effect, not a measurement error. Mercury's propeller guide notes that cupping usually lowers wide-open-throttle RPM by about 150 to 300 compared with an uncupped propeller of the same pitch, so a cupped propeller and a plain propeller are not directly comparable on RPM either.

      Negative slip means the actual speed is higher than the theoretical speed: the boat went further per revolution than the pitch promises. That cannot happen on a steady run in still water. Worked example: a 17-inch pitch at 5,000 RPM and a 2.00:1 ratio gives a theoretical speed of 17 x 5,000 / (2.00 x 1056) = 40.25 mph. If the GPS reads 42 mph, the slip is (40.25 - 42) / 40.25 x 100 = -4.3%, and the boat apparently advances 17.74 inches per revolution, more than the 17-inch pitch. Something is wrong: a current or tailwind pushing the GPS speed, a tachometer reading low, a gear ratio entered too high, or a pitch that is higher than the stamp says after a re-pitch. The calculator flags negative slip as a measurement problem and lists the checks. A tiny negative figure, within half a point of zero, can be rounding and test noise, but anything past -1% deserves a re-test.

      Zero slip deserves a note of its own. Slip of exactly 0% means the boat advanced exactly one pitch length per revolution, which would need the propeller to work in a solid medium. In water it does not happen on a real boat. A zero reading is a sign that the figures were rounded or the test was run with a current, not a sign of a perfect propeller. And zero slip would not be a good thing if it were real: as Mercury explains, without some slip the propeller blades have no angle of attack, and without angle of attack there is no pressure difference across the blades, no lift, and no thrust. Slip is not a measure of propeller efficiency, and the propeller that makes the boat run fastest at wide-open throttle is the most efficient for that boat, whatever its slip.

      How to run a proper slip test

      A slip figure is only as good as the test behind it. The test takes ten minutes and needs calm water, a GPS, and a normal load. Do it the same way every time, and the figures become comparable across propellers, seasons, and boats.

      1. Load the boat normally. Fuel, water, gear, and passengers as you usually run. Note the load: a slip figure without a load note is hard to compare later.
      2. Clean the hull and propeller. Growth costs speed and shows up as slip. Test on a clean bottom, or note the fouling.
      3. Pick a calm stretch. Flat water, little wind, no current if you can find it. A river with current works if you run both directions.
      4. Warm the engine up, then hold wide-open throttle. Wait until the RPM and the speed are steady. Note the RPM from the tachometer and the speed from the GPS at the same moment.
      5. Run the same stretch in the opposite direction. Note the RPM and speed again. Average the two speeds: that average is the speed to enter in the calculator.
      6. Write down all four figures. Pitch from the hub stamp, gear ratio from the manual or gearcase, RPM, and the averaged GPS speed. Slip worked out from a remembered RPM is not worth the paper it is not written on.

      Two common mistakes spoil the test. The first is reading the speed from the boat's speedometer instead of a GPS. Paddle-wheel and pitot speedometers read speed through the water with their own errors, and a pitot tube clogged with weed reads low, which inflates the slip. The second is testing with the engine trimmed wrong: trimmed too far out, the propeller ventilates and the slip jumps; trimmed too far in, the bow plows and the speed falls. Trim the boat to its normal running attitude, the way you run it day to day, and note the trim setting.

      If you test at cruise RPM rather than wide-open throttle, say so in your notes and do not compare the figure with wide-open-throttle figures. Slip at cruise is a different measurement: the boat may not be fully on plane, the propeller is loaded differently, and the number will usually be higher. The calculator still computes it, and it warns when the RPM is below 4,000, but the band verdicts are wide-open-throttle verdicts. Our Tide Height Calculator times the tide for the test run, and our Boat Fuel Cost and Range Calculator estimates the fuel burn for the day.

      How to pick a propeller pitch

      Pitch is the main tuning variable on a propeller. More pitch means more speed per revolution and more load on the engine, so the engine turns more slowly. Less pitch means less speed per revolution and less load, so the engine turns faster. The goal is a pitch that lets the engine reach its recommended wide-open-throttle RPM range with a normal load aboard. Get that right and most other performance issues fall into place; get it wrong and the engine either lugs below its range or over-revs above it, and no slip figure will save the setup.

      The calculator's pitch mode works out the pitch from the speed you want. Enter the target speed, the RPM you want the engine to reach at full throttle, the gear ratio, and the slip you expect. The tool works out the no-slip speed needed (target speed divided by one minus the slip), then the pitch that produces it. Worked example: a target of 55 mph at 5,800 RPM with a 1.75:1 ratio and 12% slip needs a no-slip speed of 55 / (1 - 0.12) = 62.50 mph, and the pitch is 62.50 x 1.75 x 1056 / 5,800 = 19.91 inches. The nearest stock pitch is 20 inches, which gives 55.24 mph at 12% slip.

      Propellers are sold in whole-inch pitches, so the exact figure is never the answer: the answer is the nearest whole inch, confirmed by a sea trial. The calculator shows the neighboring pitches so you can see the cost of rounding: in the example above, 19 inches gives 52.48 mph and 21 inches gives 58.00 mph at the same RPM and slip. If the 20-inch propeller leaves the engine below its RPM range on the water, drop to 19 inches; if it lets the engine over-rev, go to 21 inches. Mercury's propeller manual gives the rule of thumb for these adjustments: adding 1 inch of pitch reduces wide-open-throttle RPM by 150 to 200, removing 1 inch raises it by 150 to 200, and switching from a three-blade to a four-blade propeller of the same pitch generally lowers it by 50 to 100.

      The slip assumption matters as much as the target speed. A pitch picked for 12% slip gives a different answer from the same target picked for 15% slip: at 55 mph, 5,800 RPM, and a 1.75:1 ratio, 15% slip needs a no-slip speed of 55 / (1 - 0.15) = 64.71 mph and a pitch of 64.71 x 1.75 x 1056 / 5,800 = 20.62 inches, against 19.91 inches at 12% slip. That is most of an inch of pitch riding on a 3-point slip assumption. If you have a measured slip figure for the boat, use it. If you do not, leave the target slip blank and the calculator uses the middle of the normal band for your hull type, which is the honest default.

      The gear ratio is the other number that decides the answer, and it is the one most often entered wrong. The common outboard ratios are:

      MakerCommon gear ratiosWhere to confirm
      Mercury1.62:1, 1.75:1, 2.00:1Gearcase stamp, service manual
      Yamaha1.75:1, 2.00:1, 2.33:1Gearcase stamp, service manual
      Other outboards and sterndrives1.62:1 to 2.50:1Service manual, gearcase stamp

      These are common values, not guarantees for any particular model: other ratios exist on specific engines, and the only reliable figure is the one for your engine. A ratio entered one step wrong changes the theoretical speed by roughly the ratio of the two numbers: entering 1.75:1 for a 2.00:1 gearcase makes the theoretical speed 2.00 / 1.75 = 1.14 times too high, about 14% too high, which pushes the slip up by roughly 11 points, so a boat truly slipping 14% would read about 25%. That is the difference between a normal reading and a worrying one, from a single wrong digit. For the rest of the boat, our Boat Capacity Calculator checks persons and weight limits, our Sailboat Hull Speed Calculator works out the hull-speed limit for a displacement hull, and our Anchor Size and Rode Calculator sizes ground tackle for the boat.

      Speed units: mph, knots, and kilometers per hour

      Boat speed is measured in three units, and the slip formula works in any of them as long as the theoretical speed and the actual speed use the same unit. The calculator converts everything to mph internally, because the 1056 constant is an mph constant, then converts back for display. The slip percentage is identical in every unit: it is a ratio, and the units cancel.

      The conversions are exact: 1 knot = 1.15078 mph, and 1 kilometer per hour = 0.621371 mph. So 50.2 knots is 50.2 x 1.15078 = 57.77 mph, 40 knots is 40 x 1.15078 = 46.03 mph, and 80 kilometers per hour is 80 x 0.621371 = 49.71 mph. Going the other way, 63.54 mph is 63.54 / 1.15078 = 55.22 knots, and 46 mph is 46 / 0.621371 = 74.03 kilometers per hour. Our Unit Converter handles any other speed conversion you need.

      Boaters working in knots often use a shortcut: divide by 1,215 instead of 1,056. The theoretical speed in knots is pitch x engine RPM / (gear ratio x 1215). The 1,215 is the mph constant converted: 1,056 x 1.15078 = 1,215.22, rounded to 1,215. The shortcut is accurate to the nearest tenth of a knot in most cases: the Skeeter example gives 3,050 x 22 / 1,215 = 55.2 knots against the exact 55.22 knots, and the slip comes out 9% either way at whole-percent precision. The calculator uses the exact conversion rather than the shortcut, so its knots figures are exact to two decimal places.

      One unit mistake is worth warning about. Some GPS units can display speed in kilometers per hour while the boater reads it as mph, or the other way around. A speed of 80 read as mph when it is really 80 kilometers per hour (49.71 mph) makes the slip come out far too low, often negative. If the calculator reports a negative slip on a run that felt normal, check the GPS unit setting before anything else.

      Features

      Two modes in one tool. Slip mode measures slip from a test run: pitch, RPM, gear ratio, and actual speed. Pitch mode works backwards from a target speed, RPM, gear ratio, and target slip to a suggested pitch, with the nearest whole-inch stock pitch and the speeds of the neighboring pitches. Both modes share the same formula, so the answers agree with each other: the pitch the pitch mode suggests for a given target is the pitch that produces that target at the stated slip.

      Hull-type bands. The verdict is judged against the normal band for your hull type, not a single number. Performance boats, runabouts, cruisers, and displacement hulls each get their own band, drawn from Mercury's guidance, propeller-shop tables, and published sea-trial medians. The same slip percentage gets a different verdict on different hulls, because it means something different.

      Full working printed. Every result shows the shaft speed, the theoretical speed, and the slip as equations with the numbers filled in, so you can check each step on a pocket calculator. Displayed numbers are computed from displayed values, so the printed equations balance on their printed numbers. The one exception is the verdict itself, which tests the unrounded slip: a slip of 15.04% is above the 10-15% band even though it displays as 15.0%, and the guidance says so plainly instead of printing a contradiction.

      Speed at every slip level. The results table shows the speed the same setup would run at 5, 10, 15, 20, and 25% slip. It answers the "what if" question directly: how much speed would I gain if I fixed the slip, and how much would I lose if it got worse.

      Three speed units. Miles per hour, knots, and kilometers per hour, converted exactly. The knots shortcut divisor of 1,215 is documented in the content, and the calculator's exact conversion matches it to the nearest whole percent.

      Gear ratio presets. One-tap buttons for the common Mercury and Yamaha ratios, with a reminder to confirm the ratio on the gearcase stamp. The ratio is the input most often entered wrong, and the presets make the common values hard to mistype.

      Branch-aware warnings. The warnings fire on the conditions that produce them: negative slip, slip under 5%, slip over 20% on a planing hull, slip over 25% against Mercury's guidance, slip over 40% on a displacement hull, RPM below 4,000 or above 6,500, and a suggested pitch outside the usual 5 to 40 inch range. Each warning says what to check, not just that something is wrong.

      Worked examples built in. Four example buttons under the form load real scenarios: a normal runabout, a high-slip runabout, a pitch suggestion, and a knots example from a published Yamaha sea trial. Each one shows a different shape the answer takes.

      Use cases

      Buying a propeller. You know the boat, the engine, and the speed you want. Pitch mode turns the target into a pitch, shows the nearest stock pitch and its neighbors, and tells you what one inch up or down costs in speed. Take the figure to a propeller shop as a starting point, and confirm it with a sea trial before buying.

      Diagnosing a slow boat. The boat used to run 48 mph and now runs 42 mph at the same RPM. Work out the slip for both runs: if the slip has climbed from 12% to 22%, something has changed, and the cause is usually a fouled hull, a damaged propeller, a spun hub, or extra load. The slip figure separates a propeller problem from an engine problem: if the RPM is the same and the speed has fallen, the propeller or the hull is the suspect, not the engine.

      Comparing two propellers. Run the same test with each propeller, same load, same water, same day, and compare the slip figures. The propeller with the lower slip is not automatically the better one: the propeller that makes the boat run fastest at wide-open throttle is the most efficient, whatever its slip. But the slip figures tell you how much of each propeller's pitch is being wasted, and they make the comparison fair across different pitches.

      Checking a new-to-you boat. A sea trial on a boat you are thinking of buying should include a slip check. A slip figure well above the band for the hull type, on a clean bottom with a normal load, is a negotiating point: it may mean a worn propeller, a wrong propeller, or a hull problem. A figure inside the band is one more sign the boat is set up right.

      Tracking a boat over a season. Measure the slip the same way at the start of the season and again later. A figure that creeps up over the season usually means fouling; a figure that jumps suddenly usually means damage or a spun hub. Two numbers and a date are worth more than a vague feeling that the boat is slower than it was.

      Settling a dockside argument. Two boats with the same engine and different propellers, or the same boat before and after a propeller change: the slip figures settle whether the change helped, and by how much, in numbers both sides can check.

      Sources

      Every figure on this page was re-verified against its original publisher on 20 November 2026. The formula, the 1056 constant, and the Mercury slip band come from the sources below; the hull-type bands combine Mercury's guidance with propeller-shop tables and PropBench's sea-trial medians, and the page says which is which.

      • Mercury Marine, "Prop Bite: Understanding Propeller Slip" — calculated slip of 5% to 25% is typical and acceptable; slip greater than 25% likely means an issue with the propeller; slip is not a measure of propeller efficiency; some slip is essential because the blades need an angle of attack to produce thrust.
      • PropBench, "Propeller slip: what is normal and how to calculate it", updated 5 November 2026 — sea-trial medians by drive and hull (outboard 9%, sterndrive 11%, shaft planing 20%, shaft displacement 38%); the knots divisor of 1,215; the Skeeter ZX 190 Yamaha test worked example; the spun-hub line test.
      • Mercury Marine propeller manual 90-830296005, February 2010 — adding 1 inch of pitch reduces wide-open-throttle RPM by 150 to 200; removing 1 inch raises it by 150 to 200; switching from a three-blade to a four-blade propeller of the same pitch generally lowers wide-open-throttle RPM by 50 to 100.
      • Dunnrite Propellers, "Prop Tips 3" — the theoretical speed formula (pitch x RPM / 1056 / gear ratio), the 19-inch pitch at 6,000 RPM worked example, and indicative slip values by boat type.
      • OmniCalculator, "Prop Slip Calculator" — the slip formula with the theoretical speed in the denominator, and the note that boat propellers commonly slip 10% to 20%.

      Two conflicts in the sources were resolved in favor of the primary source. First, the brief's "normal 10-15%, over 20% signals a problem" against Mercury's "5-25% typical, over 25% a likely issue": both are right, at different breadths. The 10-15% figure is the runabout band; Mercury's 5-25% is the broad band across boat types. This calculator uses hull-type bands for the verdict and applies the over-20% warning to planing hulls and the over-25% warning to every planing hull, quoting Mercury. Second, one older web page divides the speed difference by the actual speed instead of the theoretical speed. Mercury, Yamaha sea-trial practice, OmniCalculator, and the propeller guides all divide by the theoretical speed, so the standard governs and the outlier is noted in the "How it works" section.

      Frequently asked questions

      What is a good propeller slip percentage?

      It depends on the hull. A performance boat should slip 5 to 10%, a runabout 10 to 15%, a cruiser 15 to 25%, and a displacement hull 25 to 40%. Mercury Marine says calculated slip of 5% to 25% is typical and acceptable across outboard and sterndrive boats, and slip above 25% likely means a propeller issue. In published sea trials, outboards slipped a median of 9% at full throttle, sterndrives 11%, planing boats on a shaft 20%, and displacement boats on a shaft 38%, so the slower the boat, the more slip is normal. Judge your figure against the band for your hull type, not against a single number.

      How do you calculate propeller slip?

      Work out the theoretical speed first: pitch in inches times engine RPM, divided by the gear ratio times 1056. Then subtract the actual GPS speed, divide by the theoretical speed, and multiply by 100. For example, a 19-inch pitch at 5,500 RPM with a 1.85:1 gear ratio gives a theoretical speed of 19 times 5,500 divided by 1.85 times 1056, which is 53.49 mph. At an actual speed of 46 mph, the slip is 53.49 minus 46, divided by 53.49, times 100, which is 14.0%. The 1056 converts inches per minute to miles per hour: 63,360 inches in a mile divided by 60 minutes in an hour.

      What does it mean if my prop slip is over 20%?

      On a planing hull, slip over 20% signals a problem worth investigating: the boat is giving up a fifth of its pitch advance. The usual causes are a damaged or worn propeller, a fouled hull, too much load, the wrong trim, ventilation from a motor mounted too high, or a spun hub. Mercury Marine treats slip above 25% as a likely propeller issue. On a displacement hull, over 20% is not a problem at all: displacement hulls normally slip 25 to 40%, and only slip above 40% is high for them. Check the figure against the band for your hull type, fix the easy causes first, and re-measure after each fix.

      What does negative propeller slip mean?

      Negative slip means the actual speed was higher than the theoretical speed, so the boat apparently went further per revolution than the pitch promises. That cannot happen on a steady run in still water, so a figure is off. The usual suspects are a current or a tailwind pushing the GPS speed up, a tachometer reading low, a gear ratio entered too high, a pitch higher than the stamp says after a re-pitch, or a GPS set to kilometers per hour while you read it as mph. Run the test in both directions on calm water, average the two speeds, check the tachometer against a handheld meter, and confirm the gear ratio on the gearcase stamp.

      Is zero propeller slip possible or good?

      No, on both counts. Zero slip would mean the boat advanced exactly one pitch length per revolution, which needs the propeller to work in a solid medium. In water it does not happen on a real boat, and a zero reading means the figures were rounded or the test ran with a current. It would not be a good thing if it were real: as Mercury Marine explains, without some slip the propeller blades have no angle of attack, and without angle of attack there is no pressure difference across the blades, no lift, and no thrust. Slip is not a measure of propeller efficiency, and the propeller that makes the boat run fastest at wide-open throttle is the most efficient for that boat, whatever its slip.

      How do I pick the right propeller pitch?

      Start from the speed you want and the RPM you want the engine to reach at full throttle. This calculator's pitch mode works out the pitch from those two figures plus the gear ratio and the slip you expect: a target of 55 mph at 5,800 RPM with a 1.75:1 ratio and 12% slip needs a pitch of 19.91 inches, so the nearest stock pitch is 20 inches. Propellers are sold in whole-inch pitches, so fit the nearest whole inch and confirm it with a sea trial. Mercury's rule of thumb helps with adjustments: adding 1 inch of pitch reduces wide-open-throttle RPM by 150 to 200, and removing 1 inch raises it by 150 to 200. The goal is a pitch that lets the engine reach its recommended wide-open-throttle RPM range with a normal load aboard.

      Why does slip change with load and speed?

      Slip measures the whole setup, not just the propeller. More load means more hull in the water and more drag, so the same propeller at the same RPM moves the boat more slowly and the slip rises. A fouled hull does the same thing. Speed matters because slip is highest before the boat climbs onto plane, when the hull is pushing a large bow wave, and falls as the boat planes and the wetted area shrinks. That is why slip is measured at wide-open throttle with a normal load, and why figures from different loads or different speeds are not comparable. Always note the load when you record a slip figure.

      Should I measure slip at wide-open throttle or at cruise?

      Measure at wide-open throttle. That is the standard condition: the boat is fully on plane, the speed is steady, and the figure is comparable between boats, between propellers, and between test days. A cruise reading is a different measurement, usually higher, because the boat may not be fully on plane and the propeller is loaded differently. If you do measure at cruise, say so in your notes and do not compare the figure with wide-open-throttle figures. Either way, run the same stretch in both directions on calm water and average the two GPS speeds, so current and wind roughly cancel out.