How Long Does a 5Ah Battery Last?
Estimated trigger time per charge
56.7 minutes
Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.
How to use the Cordless Drill Battery Runtime Estimator
How long does a 5Ah battery last? It depends on the job: the same pack gives nearly an hour of trigger time drilling pine and under 20 minutes on a hole saw. This estimator answers the question for your pack and your job. Pick your battery and task, set the duty cycle and the pack age, and it gives you the runtime per charge in trigger and wall-clock minutes, the holes or screws per charge, and the packs the job needs.
- Pick your battery pack. Choose the pack you own: DEWALT 20V MAX 5.0Ah, Milwaukee M18 5.0Ah, Makita 18V LXT 5.0Ah, Ryobi 18V ONE+ 4.0Ah, or Bosch 18V 4.0Ah. The specs come from the manufacturer listings, so the volts and amp-hours are the ones printed on the pack. If your pack is not listed, choose the custom option and enter its voltage and amp-hours from the label.
- Pick the task. Choose the work you are actually doing: drilling softwood, drilling hardwood, drilling metal, driving screws, hole saw, or spade bit. This choice moves the answer most: a spade bit draws about 320 watts while the trigger is pulled, a twist bit in pine about 90 watts.
- Set the duty cycle. Enter the percentage of the clock you actually spend with the trigger pulled. Forty percent is a typical DIY pace. Use 25 percent for occasional work with lots of setup, 60 percent for steady work, and 80 percent for near-continuous drilling. The duty cycle turns trigger time into wall-clock time.
- Judge the battery condition. Pick the age and condition of the pack. A new pack holds its full rated capacity. A pack two to four years old with regular use holds about 80 percent. A worn pack that already feels short on runtime holds about 50 percent. Battery University puts typical lithium-ion life at 300 to 500 full cycles, so an old pack is not a small correction.
- Enter the job size. Count the holes to drill or the screws to drive and enter the total. The estimator divides the job by the holes or screws per charge and rounds up to whole packs.
- Read your result. The big number is the estimated trigger time per charge: how long the drill actually runs before the pack empties. Below it you get the pack energy in watt-hours, the usable energy, the wall-clock time at your duty cycle, the holes or screws per charge, and the packs needed for the job. The notes name the watt draw, the seconds per hole or screw, and the efficiency factor, so you can judge every number.
This estimator is one of the free tools on Tools Elite. The watt-hour math is the same for every rechargeable pack: our Power Bank Capacity Planner uses the same energy arithmetic to size a power bank for phones and laptops. If the job is bigger than a drill, our Home Generator Size Calculator works out the running and starting watts a generator must cover. Every figure on this page comes from a published source listed at the bottom, and every assumption is stated in the open.
How it works
The estimator works in five steps: pack rating to watt-hours, usable energy after efficiency and condition, trigger time from wattage, wall-clock time from duty cycle, and units per charge from seconds per hole or screw.
Step 1: pack energy in watt-hours. Watt-hours are volts multiplied by amp-hours. A DEWALT 20V MAX 5.0Ah pack is rated 100 watt-hours at the label voltage: 20 times 5.0. An 18V 5.0Ah pack holds 90 watt-hours: 18 times 5.0. An 18V 4.0Ah pack holds 72 watt-hours. A 20V 2.0Ah pack holds 40 watt-hours. Watt-hours are the honest way to compare packs: a 12V 5.0Ah pack holds 60 watt-hours, little more than half the energy of an 18V 5.0Ah pack with the same amp-hour number.
Step 2: usable energy. Not every rated watt-hour reaches the bit. The motor and controller lose energy as heat, and the battery management system holds a reserve back so the cells are never fully drained. The estimator applies an 85 percent efficiency factor, then the condition factor for the pack age: 100 percent for a new pack, 90 percent for one to two years, 80 percent for two to four years, 65 percent for four years or heavy use, and 50 percent for a worn pack. A new DEWALT 5.0Ah pack therefore gives 100 times 0.85, which is 85 usable watt-hours. The 85 percent factor is a stated assumption, and it sits close to measured reality: a test of the Bosch GBA 18V 4.0Ah pack found it delivered about 79 percent of its rated energy, 57 watt-hours instead of 72.
Step 3: trigger time. Trigger time in hours is usable watt-hours divided by the task wattage. Drilling softwood at 90 watts on 85 usable watt-hours gives 85 divided by 90, which is 0.94 hours, or 56.7 minutes of trigger time. A spade bit at 320 watts on the same pack gives 85 divided by 320, which is 0.27 hours, or 15.9 minutes. The watt draws are typical averages while the trigger is pulled, stated openly in the tasks table below.
Step 4: wall-clock time. Nobody pulls the trigger continuously. Wall-clock time is trigger time divided by the duty cycle. At a 40 percent duty cycle, 56.7 minutes of trigger time becomes 56.7 divided by 0.40, which is 141.75 minutes, rounded to 142 minutes, or 2 hours 22 minutes of wall-clock time.
Step 5: holes or screws per charge, and packs needed. Units per charge is trigger seconds divided by the seconds each unit takes. At 56.7 minutes of trigger time, which is 3,402 seconds, and 5 seconds per hole in pine, the pack drills 680 holes. Packs needed is the job size divided by units per charge, rounded up to a whole pack: a 100-hole job needs one pack, a 1,000-hole job needs two. If the pack cannot finish even one unit of the task, the estimator says so plainly and tells you to use a bigger pack.
Worked example 1: DEWALT 5.0Ah, drilling softwood, 100 holes. A new DEWALT 20V MAX 5.0Ah pack, drilling softwood at a 40 percent duty cycle, with 100 holes to drill. Pack energy is 20 times 5.0, which is 100 watt-hours. Usable energy is 100 times 0.85, which is 85 watt-hours. Trigger time is 85 divided by 90 watts times 60, which is 56.7 minutes. Wall-clock time is 56.7 divided by 0.40, which is 141.75 minutes, rounded to 142 minutes, or 2 hours 22 minutes. Holes per charge is 56.7 times 60 divided by 5 seconds, which is 680. Packs needed is 100 divided by 680, rounded up, which is 1 pack.
Worked example 2: Bosch 4.0Ah, spade bit, old pack, 150 holes. Take a Bosch 18V 4.0Ah pack, four years old, cutting 1-inch holes with a spade bit at an 80 percent duty cycle, with 150 holes to cut. Pack energy is 18 times 4.0, which is 72 watt-hours. Usable energy is 72 times 0.85 times 0.65, which is 39.78 watt-hours, rounded to 39.8. Trigger time is 39.8 divided by 320 watts times 60, which is 7.46 minutes, rounded to 7.5 minutes. Wall-clock time is 7.5 divided by 0.80, which is 9.375 minutes, rounded to 9 minutes. Holes per charge is 7.5 times 60 divided by 5 seconds, which is 90. Packs needed is 150 divided by 90, rounded up, which is 2 packs.
Calibration check. The spade-bit math was checked against a published manufacturer test. Harbor Freight lists its 20V 5.0Ah Hercules battery at about 200 1-inch holes per charge, using a self-feed spade bit in white pine with a brushless drill. The estimator gives 191 holes for the same job: 85 usable watt-hours divided by 320 watts is 15.9 minutes, or 956 seconds, divided by 5 seconds per hole. That sits about 5 percent below the manufacturer's best-case figure, which is the right side to be on.
What the estimator does not do. It does not predict runtime for hammer drilling into concrete or masonry, because the draw there depends on the hammer mechanism and the bit far more than on the battery, and no published source gives a reliable average wattage for it. It does not adjust for temperature, though cold weather shortens runtime noticeably. It does not model brushed versus brushless motors separately: the 85 percent efficiency factor represents a modern brushless drill, and an older brushed drill loses roughly another 10 percent.
What your result means
Trigger time is the battery number; wall-clock time is the job number. Trigger time is how long the drill actually runs before the pack empties. It is the number that compares packs fairly, because it strips out how fast you work. Wall-clock time is how long the job takes on the clock at your duty cycle. A 5.0Ah pack gives about 57 minutes of trigger time drilling pine, but at a 40 percent duty cycle that is 2 hours 22 minutes of wall-clock time.
Holes or screws per charge is where the estimate gets practical. Runtime in minutes is hard to picture; holes per charge is a number you can count on the job. The estimator states its assumption beside the number: 5 seconds of trigger time per quarter-inch hole in pine, 4 seconds per deck screw, 25 seconds per 2-inch hole-saw cut. If your holes are bigger, deeper, or in harder material, each one costs more seconds and the count falls.
Packs needed counts fully charged packs for non-stop work. If the estimator says two packs, it means the job needs more energy than one full charge holds. That does not always mean buying a second pack. With one pack and a charger, you can recharge between sessions: a rapid charger refills a 5.0Ah pack in about 45 to 90 minutes depending on the brand, which covers a lunch break. For jobs needing four or more packs, two packs and a fast charger usually beat four packs: one charges while the other works, and the rotation never stops.
When to buy a second pack instead of a bigger one. A bigger pack only delays the same dead stop and adds weight to the drill. A second pack of the same size gives continuous work with a charger on site and keeps the drill balanced. Buy the bigger pack only when one charge must cover a long stretch of heavy work with no charger nearby, such as roofing or remote framing.
The condition factor is the number most people skip, and it is often the biggest one. A four-year-old pack at 65 percent capacity gives little more than half the runtime of a new pack of the same model, and a worn pack at 50 percent gives half. If your drill used to last all afternoon and now dies by lunch, the battery has aged, not the drill. Battery University's storage table makes the point sharply: a pack stored a year at full charge at 25 degrees Celsius keeps about 80 percent of its capacity, and the same pack stored at 40 degrees keeps about 65 percent.
Battery packs compared
The table below is the estimator's pack chart: voltage, amp-hours, watt-hours, and charge time for each preset pack. The DEWALT row carries the nominal-voltage figure beside the label figure, because that is the number that makes the comparison honest.
| Pack | Volts | Amp-hours | Watt-hours | Charge time |
|---|---|---|---|---|
| DEWALT 20V MAX 5.0Ah (DCB205) | 20V MAX (18V nominal) | 5.0 | 100 label (90 nominal) | About 90 minutes, standard charger |
| Milwaukee M18 REDLITHIUM 5.0Ah (48-11-1850) | 18V | 5.0 | 90 | About 90 minutes |
| Makita 18V LXT 5.0Ah (BL1850B) | 18V | 5.0 | 90 | About 45 minutes, rapid charger |
| Ryobi 18V ONE+ 4.0Ah (P192) | 18V | 4.0 | 72 | About 80 minutes |
| Bosch 18V 4.0Ah (GBA 18V 4.0Ah) | 18V | 4.0 | 72 | 48 minutes to 80 percent, 65 minutes full |
The 20V MAX label is the most misunderstood number in cordless tools. DEWALT's own footnote reads: "Maximum initial battery voltage (measured without a workload) is 20 volts. Nominal voltage is 18." The pack holds five lithium-ion cells in series, each 3.6 volts nominal and about 4.0 volts fresh off the charger, so five cells give 18 volts under load and 20 volts at rest. Milwaukee, Makita, Ryobi, and Bosch print the nominal 18 volts instead. A DEWALT 20V MAX 5.0Ah pack and a Milwaukee M18 5.0Ah pack hold the same real energy: about 90 watt-hours at nominal voltage.
Amp-hours alone mislead across voltages. A 12V 5.0Ah pack holds 60 watt-hours, an 18V 5.0Ah pack holds 90, and a 20V 2.0Ah pack holds 40. Watt-hours are the single number that compares packs across voltages, brands, and platforms. When you shop for a second pack, compare watt-hours first, then weight, then charge time.
Drill tasks and their power draw
The table below is the estimator's task chart: typical average wattage while the trigger is pulled, the typical range, and the seconds each hole or screw takes. The watt draws are clearly labeled typical values, not manufacturer ratings: no drill maker publishes an average wattage per task. The values sit inside two anchors. At the low end, a cordless drill draws about 2 to 4 amps on average light work, which is 36 to 72 watts at 18 volts. At the high end, DEWALT lists the maximum power output of its DCD790 compact drill at 360 watts, so no sustained average can sit above that. The spade-bit value was checked against Harbor Freight's published holes-per-charge test, as the calibration note above explains.
| Task | Typical watts | Typical range | Seconds per hole or screw | What it assumes |
|---|---|---|---|---|
| Drilling softwood | 90 W | 60 to 130 W | 5 | 1/4 in twist bit, 2 in deep in pine |
| Drilling hardwood | 150 W | 100 to 220 W | 8 | 1/4 in twist bit, 2 in deep in oak |
| Drilling metal | 180 W | 120 to 260 W | 12 | 1/4 in bit through 1/8 in steel |
| Driving screws | 110 W | 70 to 160 W | 4 | #8 3 in deck screw into softwood |
| Hole saw | 280 W | 200 to 360 W | 25 | 2 in hole saw through 2x lumber |
| Spade bit | 320 W | 220 to 400 W | 5 | 1 in self-feed spade bit through a stud |
What pushes a task above its typical wattage. A dull bit is the biggest one: it rubs instead of cutting, so the motor works harder for longer on every hole. Hard knots, thicker steel, and larger bit diameters all raise the draw, and so does pushing hard. If your runtime comes in well below the estimate, check the bit first.
Common mistakes to avoid
Comparing packs by amp-hours across voltages. A 12V 5.0Ah pack and an 18V 5.0Ah pack carry the same amp-hour number, but the 18V pack holds 50 percent more energy: 90 watt-hours against 60. Amp-hours only compare packs on the same voltage platform. Across voltages, watt-hours are the only honest number.
Trusting the 20V label as extra power. A 20V MAX pack is an 18V nominal pack with a peak-voltage label, holding the same five cells and the same real energy as an 18V pack of the same amp-hours. The 20 volts appears only fresh off the charger with no load. Buy for the platform, the weight, the charge time, and the tools you own, not the voltage number.
Expecting the rated watt-hours at the bit. A 100 watt-hour pack does not deliver 100 watt-hours of drilling. The motor and controller lose energy as heat, and the battery management system holds a reserve back. The estimator applies an 85 percent efficiency factor, and a measured Bosch pack delivered about 79 percent of its rating. Plan on 80 to 85 percent of the label figure reaching the work, and less on an old pack.
Forgetting the battery age. Lithium-ion loses capacity with cycles, heat, and time: Battery University puts typical life at 300 to 500 full cycles, and a pack stored a year at full charge at 40 degrees Celsius keeps about 65 percent of its capacity. Run the estimator with the condition set to new on a four-year-old pack and the answer is optimistic by about a third.
Confusing trigger time with wall-clock time. A runtime figure in minutes is trigger time, not job time. At a 40 percent duty cycle the wall clock runs two and a half times longer than the trigger, so 57 minutes of drilling is 2 hours 22 minutes of work. People who say a battery "only lasted an hour" usually mean an hour of trigger time spread over most of a morning. The estimator shows both numbers so the confusion does not happen.
Running heavy bits on a small pack. Hole saws and spade bits draw 280 to 320 watts, and a small pack drains in minutes on them while the drill runs hot. Use your biggest pack for the heavy bits, keep the small pack for screws and pilot holes, and let the pack cool between heavy cuts. A small pack on a heavy task is the fastest way to wear out a battery.
Buying packs instead of a charger. Three packs and a slow charger leave you with three dead packs by mid-afternoon. Two packs and a rapid charger keep the rotation going all day. Before buying a third pack, check what your charger does: a rapid charger is often the cheaper upgrade, and it improves every pack you already own.
Frequently asked questions
How long does a 5Ah battery last in a cordless drill?
A 5.0Ah pack holds about 90 watt-hours (100 at the 20V MAX label) and gives roughly 35 to 55 minutes of trigger time drilling wood, about 45 minutes driving screws, and about 15 to 20 minutes on hole-saw and spade-bit work. At a typical 40 percent duty cycle that is about 1.5 to 2.5 hours of wall-clock work per charge. Enter your pack, task, duty cycle, and job size above for your number.
How many holes can a 5Ah battery drill?
It depends on the hole. A 20V 5.0Ah pack drills about 200 1-inch holes with a self-feed spade bit in white pine, according to Harbor Freight's published test figures, and the estimator's math lands within 5 percent of that figure. Small pilot holes are far cheaper: the same pack drills several hundred quarter-inch holes in pine at about 5 seconds and 90 watts each. Hole saws are the opposite: a 2-inch hole saw through 2x lumber takes about 25 seconds at about 280 watts, so the same pack manages about 40 of them.
Is a 20V MAX battery really 20 volts?
Only at the moment it comes off the charger. DEWALT's own footnote reads: "Maximum initial battery voltage (measured without a workload) is 20 volts. Nominal voltage is 18." The pack holds five lithium-ion cells in series, each 3.6 volts nominal and about 4.0 volts fresh off the charger. Milwaukee, Makita, Ryobi, and Bosch print the nominal 18 volts instead. A 20V MAX 5.0Ah pack and an 18V 5.0Ah pack hold the same real energy: about 90 watt-hours at nominal voltage.
How many watt-hours is a 5Ah battery?
Multiply volts by amp-hours. An 18V 5.0Ah pack holds 90 watt-hours; a 20V MAX 5.0Ah pack is rated 100 watt-hours at the label voltage but holds about 90 at its 18V nominal voltage. A 4.0Ah pack at 18V holds 72 watt-hours, and a 2.0Ah pack at 20V holds 40 watt-hours. Watt-hours are the honest way to compare packs: amp-hours alone mislead whenever the voltages differ.
Why does my drill battery die faster than the rated runtime?
Four usual reasons. First, the task: heavy bits draw three to four times the watts of light drilling, so a hole saw empties a pack far faster than a twist bit. Second, age: a pack stored a year at full charge at room temperature keeps about 80 percent of its capacity, and one baked in a hot garage keeps about 65 percent, according to Battery University. Third, duty-cycle confusion: at a typical 40 percent duty cycle the clock runs two and a half times longer than the trigger. Fourth, cold weather and a dull bit both raise the draw and cut the runtime.
How long does it take to charge a 5Ah drill battery?
With a rapid charger, about 45 to 90 minutes depending on the brand and charger. Makita lists about 45 minutes for the 5.0Ah BL1850B on its DC18RC rapid charger, Bosch lists 48 minutes to 80 percent and 65 minutes to a full charge for its 4.0Ah pack on the GAL 18V-40, and DEWALT lists about 90 minutes for the 5.0Ah DCB205 on a standard charger. A fast charger and a second pack usually beat a bigger pack.
Should I buy a bigger battery or a second battery?
For most people, a second battery. Two 5.0Ah packs and a fast charger give continuous work: one charges while the other runs. A single bigger pack only delays the same dead stop, adds weight to the drill, and leaves you waiting when it finally empties. Buy the bigger pack only when one charge must cover a long stretch of heavy work with no charger nearby, such as roofing or remote framing.
Sources
Every figure on this page comes from one of the sources below, each accessed 20 November 2026. Watt draws per task are clearly labeled typical values, anchored by the DEWALT maximum power output and the Harbor Freight holes-per-charge test.
- Tool Nut: DEWALT DCB205 5.0Ah battery — 20V, 5.0Ah, lithium-ion, 1.5 hour charge time. Accessed 20 November 2026.
- Amazon: DEWALT DCB205-2C 2-pack listing — 200 watt-hours for the 2-pack, which is 100 watt-hours per pack at the label voltage. Accessed 20 November 2026.
- Power Tool Bench: Milwaukee M18 battery compatibility guide — XC5.0 (48-11-1850) 5.0Ah, 90 Wh at nominal 18V. Accessed 20 November 2026.
- Stine Home: Milwaukee M18 XC5.0 battery — 48-11-1850, 5.0Ah, 90 minute charge time. Accessed 20 November 2026.
- Makita BL1850B datasheet — 18V, 5.0Ah, 90 Wh energy capacity, about 45 minutes charge time with a rapid charger. Accessed 20 November 2026.
- Ryobi 18V 4.0Ah battery safety data sheet — 18V, 4Ah, 72 Wh. Accessed 20 November 2026.
- Home Depot Canada: Ryobi 18V ONE+ 4.0Ah battery — 18V, 4.0Ah, 80 minute charge time. Accessed 20 November 2026.
- Bosch Professional: GBA 18V 4.0Ah batteries and charger — 18V, 4.0Ah, to 80 percent in 48 minutes and to full in 65 minutes. Accessed 20 November 2026.
- IHL Canada: Bosch GBA18V40 battery specifications — 18V, 4.0Ah, 72.0 watt-hours. Accessed 20 November 2026.
- Power Tools Adapters: DeWalt 18V vs 20V — DEWALT footnote quoted verbatim, five cells at 3.6V nominal giving 18V, 4.0V off the charger giving 20V. Accessed 20 November 2026.
- DEWALT DCD790 and DCD795 drill instructions — 18V compact drill, power output 360 W. Accessed 20 November 2026.
- ToolsTally: How much power does a cordless drill use — most cordless drills average 2 to 4 amps, 24 to 80 watts at 12 to 20 volts. Accessed 20 November 2026.
- Harbor Freight: Hercules 20V 5Ah battery bundle — amp-hours at work per charge: 20V 2Ah drills about 90 1-inch holes, 20V 5Ah about 200, 20V 8Ah about 335, 20V 12Ah about 510, using a self-feed spade bit in white pine with a brushless drill. Accessed 20 November 2026.
- Battery University: BU-808 How to Prolong Lithium-based Batteries — manufacturers specify 300 to 500 discharge and charge cycles; storage table: at 25 degrees Celsius a pack at full charge keeps 80 percent after one year; at 40 degrees a full pack keeps 65 percent. Accessed 20 November 2026.
- idealo: Bosch Professional GBA 18V 4Ah — 18V, 4Ah, measured delivery of about 79 percent of rated energy (57 Wh instead of 72 Wh). Accessed 20 November 2026.