Skip to content

Home Security Camera Storage Calculator

cameras

Count every camera that records to the same recorder or drive, including doorbell cameras.

Higher resolution means a higher bitrate and far more storage. If your cameras differ, run the calculator once per group and add the totals.

H.265 stores the same picture in roughly half the space of H.264. Check your camera or recorder settings to see which codec it uses.

Continuous recording never misses a second. Motion-only recording saves storage but can miss an event if the trigger is set too high.

days

Thirty days is the most common retention period for a home system. After that many days, the oldest footage is deleted as new footage arrives.

Estimated storage needed

3.89 TB

Cloud or local? Local storage is a one-time drive purchase with no monthly fee, and the footage stays in your home, but a stolen recorder takes the footage with it. Cloud storage keeps clips off site, so they survive a break-in, but it charges every month and caps how many days you can review. If you are weighing a cloud plan, our security camera subscription cost calculator compares Ring, Blink, and Arlo plan prices for your camera count.

This tool provides estimates for general guidance only. Bitrates vary by scene, camera brand, and settings, so check the live bitrate on your own camera before buying a drive. Always check the manufacturer's specifications before buying.
Quick answer: A single 4K camera recording 24/7 uses about 130 GB a day on H.264 and about 65 GB a day on H.265, so one camera fills a 1 TB drive in about a week. Four 2K cameras on H.265 need about 3.89 TB for 30 days of continuous recording, which a 4 TB surveillance drive covers. Use the calculator above to work out your exact total from your camera count, resolution, codec, recording mode, and retention days.

Last reviewed: 19 November 2026. Reviewed every 180 days; next review due 18 May 2027.

How to use the Security Camera Storage Calculator

A security camera is a quiet storage hog. A single 4K camera recording around the clock burns through roughly 1 TB in about 7 days, and most buyers discover that only when the recorder starts deleting footage a week after installation. The camera box lists resolution and frame rate, then stops. It never says how many gigabytes a day that camera writes, how long a 2 TB drive will last, or what switching to H.265 would save. This calculator answers those questions before you buy the drive, using published planning bitrates for each resolution and codec.

It takes less than a minute. Enter your camera count, resolution, codec, recording mode, and retention days, and you get a total storage figure in GB and TB, a per-camera breakdown, the planning range your real usage will fall inside, and the smallest standard surveillance drive that covers your system. It also shows what the other codec would need, so you can see exactly what H.265 is worth to you, and how many days a 1 TB drive would last on your system. Every figure comes from a named, linked source listed at the bottom of this page, checked on 19 November 2026.

  1. Enter your number of cameras. Count every camera that records to the same recorder or drive, including doorbell cameras. A doorbell is a camera for storage purposes, and it is the one most often left out of the count.
  2. Pick the resolution per camera. 1080p Full HD, 2K (4 MP), or 4K Ultra HD. Resolution is the biggest single lever on storage: a 4K camera writes about three times as much per day as a 1080p camera at the same codec. If your cameras differ in resolution, run the calculator once per group and add the totals together.
  3. Pick the codec. H.264 is the older standard; H.265 (also called HEVC) is the newer one, and it stores the same picture in roughly half the space. Check your camera or recorder settings to see which codec it uses.
  4. Pick the recording mode. Continuous recording runs 24 hours a day, 7 days a week, and never misses a second. Motion-only recording writes only when the camera detects movement, which saves storage but can miss an event if the trigger is set too high.
  5. If you picked motion-only, enter your motion estimate. This is the share of the time you expect there to be motion in view, as a percentage. A quiet backyard might see motion 10 percent of the time; a camera facing a busy street can be near 100 percent. The default of 30 percent suits a typical home. Be honest here: an optimistic guess is how people end up with a drive that fills in half the time they planned for.
  6. Enter your retention days. This is how many days of footage you want to keep before the oldest footage is deleted. Thirty days is the most common retention period for a home system, and it is the default here.
  7. Read your result. You get your total storage in GB and TB, what each camera writes per day, what the whole system writes per day, the planning range, the hard drive size that covers it, how many days a 1 TB drive would last, and what the other codec would need.

How it works

Storage is bitrate multiplied by time. A camera streams a number of megabits every second, called its bitrate, and every second of that stream has to be written somewhere. The formula this calculator uses is the one every NVR storage guide publishes: storage in GB per day equals bitrate in Mbps times 10.8. The 10.8 is not a fudge factor. One megabit per second for 24 hours is 1,000,000 bits times 86,400 seconds, divided by 8 bits per byte, divided by 1,000,000,000 bytes per gigabyte, which comes to exactly 10.8 GB. So a camera running at 4 Mbps writes about 43.2 GB a day, and a camera running at 12 Mbps writes about 129.6 GB a day.

From there the arithmetic is straightforward. Total storage equals bitrate times 10.8 times the recording factor times the number of cameras times the number of retention days, divided by 1,000 to convert GB to TB. The recording factor is 1 for continuous recording, or your motion percentage divided by 100 for motion-only recording. All units are decimal: 1 TB is 1,000 GB, the way drive makers label their drives. That matters, because a drive's labeled size is decimal while your recorder may report binary units, so a 10 TB drive shows about 9.1 TB in the recorder. The calculator works in the labeled units, so the drive size it recommends is the size printed on the box.

The bitrates the calculator plans on are the low end of the published ranges for a normal scene at 25 frames per second: 1080p at 4 Mbps on H.264 and 2 Mbps on H.265, 2K at 6 Mbps on H.264 and 3 Mbps on H.265, and 4K at 12 Mbps on H.264 and 6 Mbps on H.265. Those are planning values, not measurements. Your real bitrate moves with the scene: a busy street, trees moving in the wind, rain, and night-time infrared noise all push it up, while a quiet room, a lower frame rate, and smart codecs push it down. That is why the result shows a range as well as a single number. If the footage matters, size for the high end of the range, not the middle.

Worked example: four 2K cameras, 30 days

Take a typical home system: four 2K cameras, H.265, recording 24/7, keeping 30 days of footage. The planning bitrate for a 2K camera on H.265 is 3 Mbps, so one camera writes 3 times 10.8, which is 32.4 GB per day. Over 30 days that is 32.4 times 30, which is 972 GB per camera. Four cameras write 32.4 times 4, which is 129.6 GB per day for the whole system, and 129.6 times 30, which is 3,888 GB, or 3.89 TB. The smallest standard surveillance drive that holds 3.89 TB is a 4 TB drive, and a 1 TB drive would last 1,000 divided by 129.6, which is 7.72 days.

Now change one thing at a time. Switch the same four cameras to H.264, and the planning bitrate doubles to 6 Mbps, so the total doubles to 7,776 GB, or 7.78 TB, and the drive you need becomes an 8 TB drive. Switch to motion-only recording at 30 percent instead, and the recording factor becomes 0.30, so the total drops to 3,888 times 0.30, which is 1,166.4 GB, or 1.17 TB, and a 2 TB drive covers it with room to spare. Switch to 4K cameras on H.265, and the planning bitrate doubles to 6 Mbps, so the total doubles to 7.78 TB again. Each lever is worth about a factor of two, and the levers multiply.

What your result means

Your result has five numbers that matter, and each one points to a different decision. The total storage is the number to shop against, and the drive recommendation below it is the smallest standard surveillance size that holds it. The per-camera daily figure tells you what each camera costs you in storage, which is the number to check against your camera's own settings page, where the live bitrate is usually shown. If your camera's live bitrate is well above the planning value, your real total will be above the calculator's figure, and the range will tell you by how much. The system daily figure is also the number your network carries: four cameras at 3 Mbps each push about 12 Mbps of recording traffic to the recorder, day and night. If your cameras keep dropping offline, the storage is not the problem, and our mesh WiFi node calculator works out how many nodes your home needs.

The planning range is the number most people skip and the one they most need. Your real usage will land somewhere inside it depending on how busy your scenes are. A camera watching a quiet hallway will land near the low end. A camera facing a street with passing cars, or a yard with trees moving in the wind, will land near the high end, and at night the infrared noise alone can push the bitrate up. If you buy a drive that only just holds the planning value, a busy week can fill it early and start deleting footage sooner than you planned. The safe buy is a drive that holds the high end of the range, or at least one size above the planning value. A storage guide that plans for a 10 to 15 percent margin on top of the calculated total is giving the same advice in different words.

The codec comparison is the cheapest saving in the whole result. If you are on H.264 and your cameras and recorder support H.265, switching codecs halves your storage need with no new hardware and no loss of picture quality. Check first that your recorder and your viewing devices can decode H.265: older recorders and some older phones and browsers cannot, and a codec your recorder cannot play is worse than a bigger drive. If your system supports it, H.265 is the default to choose on any camera bought in the last few years.

The days-on-1-TB figure answers the question most people actually ask first: how long will this drive last? It is also the figure that makes the 4K trade-off concrete. One 4K camera on H.264 fills a 1 TB drive in about 7.7 days. Four of them fill it in under 2 days. That is not a defect in the drive; it is what 4K costs. If you want 4K picture quality and a month of retention, you need a big drive, and this calculator tells you how big before you buy it.

Storage by resolution and codec

The table below shows the planning bitrate, the published bitrate range, and the storage one camera uses per day when it records continuously, for every resolution and codec combination in this calculator. The planning bitrates are the low end of the published ranges for a normal scene at 25 frames per second. The ranges come from a second published source, and they are wider because they cover both quiet and busy scenes. Read the table as a planning guide, not a measurement: your camera's real bitrate is shown on its own settings page or in your recorder's stream statistics, and that measured figure always beats any table.

ResolutionCodecPlanning bitrateBitrate rangeStorage per camera per day
1080p Full HDH.2644 Mbps2 to 4 Mbps43.2 GB
1080p Full HDH.2652 Mbps1 to 2 Mbps21.6 GB
2K (4 MP)H.2646 Mbps4 to 8 Mbps64.8 GB
2K (4 MP)H.2653 Mbps2 to 4 Mbps32.4 GB
4K Ultra HDH.26412 Mbps8 to 16 Mbps129.6 GB
4K Ultra HDH.2656 Mbps4 to 8 Mbps64.8 GB

Two patterns in the table are worth noticing. First, the 1080p planning bitrates sit at the top of their published ranges, while the 2K and 4K planning bitrates sit in the middle or at the low end. That is deliberate: the published 1080p figure is a single value rather than a range, and planning on the top of the range for the most common resolution is the conservative choice. Second, H.265 halves every figure in the table. That is the planning assumption this calculator uses, and it sits inside the published 40 to 50 percent saving for H.265 over H.264 at the same picture quality. One source puts the typical saving lower, at 20 to 40 percent, and the saving is always smallest in busy, high-motion scenes. The honest statement is that H.265 roughly halves storage, not that it exactly halves it in every scene.

Frame rate is the lever the table does not show, and it is worth knowing about. The planning bitrates assume 25 frames per second. Dropping to 12 to 15 frames per second almost halves the storage, and for general surveillance it costs very little: above roughly 12 to 15 frames per second, extra frames add storage without adding much forensic value, because a person walking across a frame is just as identifiable at 15 frames per second as at 30. If your recorder lets you set the frame rate, 15 frames per second is a sensible middle ground, and it makes the planning bitrates in this calculator conservative, which is the safe direction to be wrong in.

What size hard drive do you need?

The calculator recommends the smallest standard surveillance drive size that holds your total, from the sizes surveillance drives are sold in: 1, 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, and 20 TB. The table below shows how long each common drive size lasts on the typical home system from the worked example, four 2K cameras on H.265 recording 24/7, which writes 129.6 GB a day.

Drive sizeDays of footage (4 x 2K, H.265, 24/7)Who it suits
1 TBAbout 8 daysOne or two cameras, or short retention
2 TBAbout 15 daysA small system, or motion-only recording
4 TBAbout 31 daysThe typical four-camera home system
6 TBAbout 46 daysSix cameras, or 4K at short retention
8 TBAbout 62 daysEight cameras, or two months of retention

Buy a surveillance-rated drive, not a desktop drive. The two best-known lines, WD Purple and Seagate SkyHawk, are built for writing video around the clock, rated by their makers for a workload of 180 TB a year, up to 64 cameras per drive, and a three-year warranty. A desktop drive is built for short bursts of reading and writing with long idle periods, and a recorder that writes to it nonstop will wear it out early. The step-up lines, WD Purple Pro and Seagate SkyHawk AI, are rated at 550 TB a year and come in sizes up to 26 TB and 32 TB, but they are meant for systems running AI analytics on many streams, which is more than a home system asks of a drive.

Three practical points before you buy. First, check your recorder's compatibility list: recorder makers publish a list of drives they have tested with each model, and a drive that is not on the list may not be recognized. Second, remember the decimal-versus-binary gap: a drive sold as 10 TB shows about 9.1 TB in the recorder, because the label counts a terabyte as a trillion bytes while the recorder counts it as 1,099,511,627,776 bytes. Third, if your recorder has two or more bays, think about redundancy. A single drive holds everything, and if it fails, the footage goes with it. RAID 1 mirrors one drive onto a second, so a failure loses nothing, but it halves your usable capacity. RAID 5 spreads the data across three or more drives and loses one drive's worth of capacity to parity. This calculator sizes a single drive; if you run RAID, add the lost capacity to the total before you shop.

Cloud storage vs local storage

Local storage and cloud storage solve different problems. Local storage means a hard drive in your own recorder. You buy the drive once, you pay nothing per month, the footage stays in your home, and nobody can change the price or the retention rules later. Its weakness is physical: if someone steals the recorder, the footage goes with it, and if the drive fails without a mirror, the footage is gone. Cloud storage means the camera uploads clips to the maker's servers. The footage survives a break-in, you can review it from anywhere, and there is no drive to buy or replace. Its weaknesses are the monthly fee, which runs for as long as you own the camera, and the retention cap: cloud plans limit how many days you can review, and the cap is set by the plan, not by you.

The cost comparison depends on what you count. A surveillance drive is a one-time purchase that lasts for years. A cloud plan charges every month, and over three years the subscription can cost more than the cameras did. Our security camera subscription cost calculator compares Ring, Blink, and Arlo plan prices for your camera count, and it shows how fast the subscription adds up. But the cloud plan also buys something a drive cannot: off-site footage that survives the theft of the recorder, plus smart features such as person alerts that many local recorders do not offer. Many homes use both, local recording for the full timeline and a cloud plan for the clips that matter.

One more consideration is your internet connection. Every camera on a cloud plan uploads its clips over your home internet, and a 4K camera uploads a lot. Four 4K cameras on H.265 push about 24 Mbps upstream between them when they are all recording, which is more than some home internet plans offer upstream. Local recording has no such problem, because the video never leaves the house. If your upload speed is slow, or your internet provider caps your data, local storage is the safer choice, and the drive this calculator recommends is the whole of the cost.

Common mistakes to avoid

  • Planning on the resolution, not the bitrate. Two 4K cameras can write very different amounts of data. A 4K camera set to 4 Mbps writes exactly as much per hour as a 1080p camera set to 4 Mbps; it just looks worse doing it. What decides storage is the bitrate, and the bitrate depends on resolution, frame rate, codec, and scene motion together. Check the bitrate on your camera's settings page, and use the table on this page as a planning guide, not a measurement.
  • Using the maximum bitrate as the average. With variable bitrate encoding, the bitrate you set is a ceiling, not an average. Quiet scenes stay well below it, and busy scenes use all of it. If you calculate with the maximum, you are on the safe side but may buy more terabytes than you need. If you calculate with a measurement from ten quiet minutes, you will almost always underestimate.
  • Trusting motion-only recording to save 90 percent. Motion recording sounds like a huge saving and typically delivers 30 to 70 percent, depending on the scene and the source you read. Pre-event and post-event buffers extend every clip beyond the motion itself, cameras covering a street or a hallway see near-constant activity, and false triggers from weather, shadows, and headlights add clips nobody wants. It also has a failure mode: if the detection threshold is set high enough to keep storage down, it will eventually miss the event that matters.
  • Forgetting the doorbell and the indoor cameras. A video doorbell counts as a camera for storage purposes, and it is the device most likely to be left out of a head count, because people think of it as a doorbell rather than a camera. Indoor cameras count too, and they often watch the busiest rooms in the house. Count every camera that records to the same drive.
  • Buying a desktop drive for a recorder. A desktop drive is built for short bursts of activity with long idle periods. A recorder writes to it nonstop, 24 hours a day, 365 days a year. Surveillance-rated drives are built for that workload, rated at 180 TB a year, and they are the ones recorder makers test against.
  • Forgetting the sub-stream. Many cameras send two streams: a main stream at full resolution for recording, and a smaller sub-stream for live viewing on a phone. If your recorder saves both, add the sub-stream's bitrate to the total. The calculator assumes only the main stream is stored, which is the usual setup, but check your recorder's settings if your drive fills faster than the calculator predicted.
  • Ignoring the decimal-versus-binary gap. A drive sold as 4 TB holds 4 trillion bytes, but your recorder counts a terabyte as 1,099,511,627,776 bytes, so it reports about 3.6 TB of usable space. Add a 10 to 15 percent margin to the calculated total before you shop, or buy one size above the calculator's recommendation, and the gap stops mattering.
  • Keeping footage longer than you need. Every extra day of retention costs the same as the first day: the total grows in direct proportion to the retention period. Ninety days costs three times as much as thirty days. Thirty days is the most common retention period for a home system, and it covers a long holiday. If you do not have a specific reason to keep more, thirty days is the sensible default.

Frequently asked questions

How much storage does a 4K security camera use per day?

A single 4K camera recording 24/7 uses about 130 GB a day on H.264 and about 65 GB a day on H.265, at the planning bitrates of 12 Mbps and 6 Mbps. The real figure runs from about 86 GB to about 173 GB a day on H.264, depending on how much motion the scene has. That is why one 4K camera fills a 1 TB drive in about a week.

Is 1 TB enough for 4 security cameras?

It depends on the resolution and how long you keep footage. One terabyte holds about 7.7 days of four 2K cameras recording 24/7 on H.265, and about 3.9 days of the same four cameras on H.264. For 30 days of four 2K cameras on H.265 you need about 3.89 TB, so a 4 TB drive. On motion-only recording at 30 percent, the same four cameras need only about 1.17 TB for 30 days, so a 2 TB drive covers them with room to spare.

Does H.265 really halve storage?

Roughly, yes. For the same picture quality, H.265 typically needs 40 to 50 percent less bitrate than H.264, so storage drops by about the same amount. A 4K camera that needs 12 Mbps on H.264 needs about 6 Mbps on H.265. The saving is biggest in quiet scenes with little motion and smallest in busy scenes, and one source puts the typical saving lower, at 20 to 40 percent. This calculator plans on H.265 using exactly half the bitrate of H.264, which sits inside the published 40 to 50 percent range.

How much storage do I need for 30 days of camera footage?

Multiply your cameras by the storage one camera uses in a day, then multiply by 30. Four 1080p cameras on H.265 need about 2.59 TB for 30 days of continuous recording; four 2K cameras need about 3.89 TB; four 4K cameras need about 7.78 TB. Switch the same four cameras to H.264 and every figure doubles. Use the calculator above for your exact camera count, resolution, and codec.

How much does motion-only recording save?

In a quiet area, motion-only recording often saves 40 to 70 percent compared with continuous recording. But the saving depends entirely on how busy the scene is: a camera facing a street can record almost all the time, and pre-event and post-event buffers add a few seconds to every clip, so some sources put the typical saving lower, at 30 to 60 percent. This calculator lets you enter your own motion percentage instead of guessing, with 30 percent as the default for a typical home.

What size hard drive do I need for my NVR?

Pick the smallest surveillance drive that holds your total storage, then check your recorder's compatibility list. For a typical four-camera 2K system on H.265 recording 24/7, a 1 TB drive holds about 8 days, a 2 TB drive about 15 days, a 4 TB drive about 31 days, and an 8 TB drive about 62 days. Buy a surveillance-rated drive, such as WD Purple or Seagate SkyHawk, built for writing video around the clock, not a desktop drive. Remember that a drive's labeled size is decimal, so a 10 TB drive shows about 9.1 TB in the recorder.

Is cloud storage or local storage better for security cameras?

Local storage costs more up front and nothing per month: you buy a hard drive once, the footage stays in your home, and nobody can change the price later. Its weakness is that a stolen recorder takes the footage with it. Cloud storage keeps clips off site, so they survive a break-in, but it charges every month, it caps how many days you can review, and it needs your internet connection to upload every clip. Many homes use both: local recording for the full timeline, plus a cloud plan for the clips that matter. Our security camera subscription cost calculator compares Ring, Blink, and Arlo cloud plan prices for your camera count.

Sources

  • How to Calculate NVR Storage for CCTV, MadyTools — madytools.com/guides/nvr-storage-calculation/ — the storage formula, typical bitrates at 25 fps in a normal scene (1080p H.264 4 Mbps / H.265 2 Mbps; 4 MP H.264 6-8 / H.265 3-4; 4K H.264 12-16 / H.265 6-8), motion recording saving 40-70 percent in quiet areas, 12-15 fps almost halving storage, 10-15 percent margin, a 10 TB disk showing about 9.1 TB in the recorder, RAID capacity loss, 30 days the most common retention period, H.265 needing 40-50 percent less bitrate than H.264. Published 19 November 2026, accessed 19 November 2026.
  • Security Camera Storage Calculator: TB Needed in 2026, PVR Blog — pvrblog.com/cameras/tech/storage-calculator/ — a single 4K camera at 24/7 recording burns through 1 TB in about 7 days; 4K H.264 12-16 Mbps (130-170 GB a day) and H.265 6-8 Mbps (65-86 GB a day); storage (GB) = cameras x bitrate (Mbps) x days x 10.8; heavy motion adding about 50 percent, static scenes cutting numbers in half. Accessed 19 November 2026.
  • H.264 vs H.265 in 2026: Camera Codec Compared, PVR Blog — pvrblog.com/tech/h264-vs-h265/ — H.265 producing files roughly half the size of H.264 at the same visual quality; per-day file sizes at 15 fps (1080p 20 GB H.264 / 10 GB H.265; 2K 32 GB / 16 GB; 4K 60 GB / 30 GB); savings by scene type (static porch 58 percent, average daytime 50 percent, high motion 42 percent). Accessed 19 November 2026. Note: this source's 15 fps per-day figures run about half the planning bitrates used by this calculator; see the documented disagreement in the README.
  • Security Camera Bandwidth and How Much Cameras Use, Surveillant.ai — surveillant.ai/guides/security-camera-bandwidth — typical bitrate ranges at 30 fps: 1080p H.264 2-4 Mbps / H.265 1-2; 4 MP H.264 4-8 / H.265 2-4; 4K H.264 8-16 / H.265 4-8; 1 Mbps of continuous recording is about 10.8 GB per camera per day. Accessed 19 November 2026.
  • CCTV Storage Calculator: The Surveillance Retention Math, Fora Soft Learn — forasoft.com/learn/video-surveillance/articles-vms/surveillance-storage-retention-math — 1 Mbps x 86,400 seconds / 8 = 10.8 GB a day; bitrate ranges at 15-30 fps (1080p H.264 2.5-5 / H.265 1.5-3; 4 MP H.264 3.2-8 / H.265 2.2-4.2; 4K H.264 8-12 / H.265 4-10); H.265 roughly halving H.264, vendors typically citing a 30-50 percent bitrate reduction. Accessed 19 November 2026.
  • How to Size NVR Storage for Your Camera System, Revolvis — revolvis.com/blog/how-to-size-nvr-storage-days-of-footage/ — planning bitrate ranges (1080p H.265 1-2 / H.264 2-4; 4 MP H.265 2-4 / H.264 3-6; 4K H.265 4-8 / H.264 6-12); storage in GB = cameras x bitrate x 10.8 x days. Accessed 19 November 2026.
  • CCTV Storage Calculator, Kilo Electronics — kiloelectronics.com/en/cctv-storage-calculator/ — 1 Mbps for 24 hours is 10.8 GB; a 4 MP camera on H.265 at 25 fps lands between 2 and 4 Mbps, an 8 MP (4K) camera between 4 and 8 Mbps; about 90 percent of nominal capacity available for video; the configured maximum bitrate is a ceiling, not an average. Accessed 19 November 2026.
  • Motion recording savings, three sources — Radiatus CCTV Storage Calculator (online-tools.radiatus.com/tools/cctv-storage-calculator, motion recording typically saving 30-60 percent, updated 11 October 2026); IP Security Depot Retention Modeling and Storage Guide (ipsecuritydepot.com/guides/retention-modeling-storage-guide/, motion-only typically saving 60-80 percent, updated 18 April 2026); Fora Soft Recording-Strategy Decision Guide (forasoft.com/learn/video-surveillance/articles-vms/recording-strategies-continuous-motion-event, motion recording at about 20-50 percent of continuous storage). All accessed 19 November 2026.
  • H.264 vs H.265: What Changes for Security Camera Footage?, ieGeek — uk.iegeek.com/blogs/security-basic/h264-vs-h265 — H.265 using 20-40 percent less data at similar quality, a lower saving than the 40-50 percent other sources cite; at the same bitrate both codecs produce files of roughly the same size. Accessed 19 November 2026.
  • Seagate SkyHawk vs WD Purple: Best NVR Hard Drive (2026), Gypsyi — gypsyi.com/articles/seagate-skyhawk-vs-wd-purple-security-camera-nvr-hard-drive-compared — both lines rated for up to 64 HD cameras, 180 TB a year, 1 million hours MTBF, three-year warranty; core capacities 1 TB to 8 TB; SkyHawk AI 8 TB to 32 TB. Published 12 November 2026, accessed 19 November 2026.
  • Surveillance Hard Drive: WD Purple vs SkyHawk vs S300, ratioDB — ratiodb.com/guides/surveillance-hard-drive/ — WD Purple, Seagate SkyHawk, and Toshiba S300 rated at 180 TB a year; WD Purple Pro and SkyHawk AI at 550 TB a year with five-year warranties. Published 28 October 2026, accessed 19 November 2026.
  • CCTV Hard Drive: Workload Tiers, Sizes and Amazon.co.uk Prices, DataCenterDisk — datacenterdisk.com/uk/cctv-hard-drive — WD Purple 1 TB to 8 TB at 180 TB a year, AllFrame AI models at up to 360 TB a year, WD Purple Pro 8 TB to 26 TB at 550 TB a year. Prices checked 19 November 2026, accessed 19 November 2026.
  • NVR Hard Drive Storage Sizing: Bitrate and Capacity Guide, Home Resilience Hub — homeresiliencehub.com/blog/home-security/nvr-hard-drive-storage-bitrate-calculation-guide/ — H.265 at 15 fps: 1080p 2 Mbps (21.6 GB a day), 2K 4 Mbps (43.2 GB a day), 4K 6 Mbps (64.8 GB a day). Published 7 November 2026, accessed 19 November 2026.
  • How to Calculate CCTV Storage: A Complete Guide, Arditec — arditec.co.il/en/blog/how-to-calculate-cctv-storage — above roughly 12-15 fps, additional frames add storage without adding much forensic value; motion-triggered recording can reduce write volume by 50-70 percent in low-traffic areas; a high detection threshold will eventually miss the event that matters. Accessed 19 November 2026.

Bitrates vary by scene, camera brand, and settings, so treat every figure on this page as a planning estimate and check the live bitrate on your own camera's settings page before you buy. This page was last reviewed on 19 November 2026, and the next review is due on 18 May 2027. If you are also weighing a cloud plan, see our security camera subscription cost calculator, and if your cameras need a stronger network, see our mesh WiFi node calculator. For storage questions on a laptop rather than a recorder, see our laptop storage size calculator. You can find all our tools from the Tools Elite homepage.