Skip to content

What PSI Pressure Washer Do I Need?

Every surface has its own safe pressure range. A car wants 1,200 to 1,900 PSI; a concrete driveway wants 2,000 to 3,000. Pick the surface that matches your job, not the machine you already own.

Area to clean
sq ft

Length times width, in feet. For a car or patio furniture, enter the area of the space around it; the area does not change the pressure, it only affects whether a gas machine is worth it on a large flat surface.

Dirt level moves the recommendation inside the surface's safe range. Heavy dirt never pushes a surface past its safe ceiling: for heavy dirt, detergent and a second pass do more than extra pressure.

Recommended pressure

2,000 to 3,000 PSI

This tool provides estimates for general guidance only. Safe pressure depends on the age and condition of your surface, and weathered wood, loose paint, crumbling mortar, and oxidized siding all need less pressure than the chart. Always check the manufacturer's specifications before buying.
Quick answer: Most homes need 1,200 to 1,900 PSI for a car, 500 to 1,200 PSI for a wood deck, 1,300 to 1,600 PSI for vinyl siding, and 2,000 to 3,000 PSI for a concrete driveway. Never go above 2,000 PSI on a car, 1,500 PSI on a pine or cedar deck, or 3,500 PSI on concrete. Enter your surface, area, and dirt level above to get the safe range, the GPM, the cleaning units, and the nozzle for your job.

Last reviewed: 19 November 2026. Reviewed every 180 days; next review due 18 May 2027.

How to use the Pressure Washer PSI Finder

What PSI pressure washer do I need? The answer depends on the surface you are cleaning, not on the biggest number on the box. A car wants 1,200 to 1,900 PSI, a wood deck wants 500 to 1,200, and a concrete driveway wants 2,000 to 3,000. Use the driveway number on a car and you will lift the paint; use the car number on a driveway and you will still be out there at sunset. This finder matches the pressure to the surface, then adjusts for how dirty it is, and warns you before you cross the line where cleaning turns into damage. It takes less than a minute.

  1. Pick the surface. Choose the surface that matches your job: car or truck, wood deck, concrete driveway, siding, patio furniture, wood fence, or brick. If your job covers two surfaces, run the finder twice and use the gentler result for the delicate one. A deck and the concrete patio beside it are two different jobs with two different pressures.
  2. Enter the area. Measure the length times the width of the area in feet and enter the total in square feet. For a car or patio furniture, enter the area of the space around it. The area does not change the pressure: it only affects whether a gas machine is worth it on a large flat surface, where flow finishes the job faster.
  3. Judge how dirty it is. Light dirt is dust, pollen, and light grime. Moderate dirt is ground-in grime, algae, and mildew. Heavy dirt is oil stains, thick moss, and years of buildup. If you are between two levels, pick the dirtier one: the finder moves the recommendation inside the safe range, and heavy dirt never pushes a surface past its safe ceiling.
  4. Read your result. You get the recommended PSI range, the GPM range, the cleaning units, the nozzle to use, whether an electric or gas machine fits the job, and a warning that names the exact damage too much pressure causes on that surface. Read the warning before you pull the trigger: every one of those failures is permanent.
  5. Test before you commit. The finder tells you the pressure; your surface tells you the truth. Test a hidden spot first, start with the widest nozzle, stand back, and close the distance slowly. If the test spot cleans up at the low end of the range, stay there. The lowest pressure that lifts the dirt is the right pressure.

This finder is one of the free tools on Tools Elite. Every range on this page comes from a published source listed at the bottom: manufacturer guidance from Simpson, buying guides from Bob Vila and Family Handyman, and working ranges used by professional cleaners. If you are washing the house before painting, our Paint Coverage Calculator works out how much paint the freshly washed walls will need. The finder gives estimates for general guidance, not a guarantee for any one surface, so always check the manufacturer's specifications for your machine and your surface before you buy or spray.

How it works

The finder works in four steps: it looks up the surface's safe pressure range, it moves inside that range by dirt level, it multiplies pressure by flow to get cleaning units, and it picks electric or gas from the pressure and the size of the job.

Step 1: look up the surface range. Each surface has a published safe range. A car is 1,200 to 1,900 PSI, from Family Handyman's guide to pressure washing a car. A concrete driveway is 2,000 to 3,000 PSI, from a contractor quoted by Bob Vila, who warns that going higher can etch the concrete. A wood deck is 500 to 1,200 PSI, the range professional cleaners use for softwood, with a 1,500 PSI ceiling for pressure-treated pine and cedar. Vinyl siding is 1,300 to 1,600 PSI. Patio furniture is 1,200 to 2,000 PSI. A wood fence is 1,500 to 2,000 PSI. Brick is 2,000 to 3,000 PSI. Each surface also has a flow range in gallons per minute, because pressure without flow is only a fine jet: Bob Vila puts it plainly, that high pressure with low flow gives only a fine jet, while high pressure and high flow together clean a wider area with force.

Step 2: adjust for dirt level. The dirt level moves the recommendation inside the safe range, using the midpoint of the range rounded to the nearest 100 PSI. Light dirt takes the low end to the midpoint. Moderate dirt takes the full range. Heavy dirt takes the midpoint to the top of the range. A wood deck has a base range of 500 to 1,200 PSI, so its midpoint is 850, rounded to 900: light dirt gives 500 to 900 PSI, moderate dirt gives 500 to 1,200, and heavy dirt gives 900 to 1,500, where 1,500 is the ceiling for pine and cedar rather than the top of the base range. Heavy dirt never pushes a surface past its safe ceiling. For heavy dirt the finder adds a detergent note instead, because detergent and a second pass do more than extra pressure, and they do not damage the surface.

Step 3: work out cleaning units. Cleaning units, or CU, are PSI multiplied by GPM. Simpson defines them exactly that way: the combination of PSI and GPM results in cleaning units, calculated by multiplying PSI and GPM. The finder reports the range from the low end of both numbers to the high end of both. A machine rated at 2,000 PSI and 2.5 GPM delivers 5,000 cleaning units; the same pressure at 4.0 GPM delivers 8,000. That is why two machines with the same PSI can clean at very different speeds, and why the finder shows flow beside pressure instead of letting PSI stand alone.

Step 4: pick electric or gas. The finder recommends a gas machine when the top of the PSI range is above 2,500, or when concrete or brick covers more than 1,500 square feet. Everything else gets an electric recommendation. The rule follows Bob Vila's bands: most household electric washers run 1,500 to 3,000 PSI with 1.5 to 2.5 GPM, while gas washers are seldom under 2,500 PSI and run 2.5 to 4.0 GPM. Above 2,500 PSI the flow a gas machine carries is what finishes the job, and on a large flat area the same is true even at lower pressure: a gas machine's extra gallons per minute cover ground faster. Simpson makes the same point from the other side: for larger jobs, or more frequent use, a gas machine may be worth looking into, while an electric machine suits smaller jobs used once or twice a year.

Worked example 1: a car with moderate dirt. Take a car with ground-in road film, 400 square feet of space around it. The car range is 1,200 to 1,900 PSI, and moderate dirt takes the full range. The GPM range is 1.4 to 2.0. Cleaning units run from 1,200 times 1.4, which is 1,680, to 1,900 times 2.0, which is 3,800. The top of the range, 1,900 PSI, is at or below the 2,500 gas line, so the power type is electric. The nozzle is the 40 degree white nozzle for paint, with the 25 degree green nozzle only for wheels and caked-on mud. The warning names the ceiling: above 2,000 PSI with a narrow nozzle risks lifting paint and clear coat.

Worked example 2: a concrete driveway with heavy dirt. Take a 600 square foot driveway with oil stains and years of buildup. The concrete range is 2,000 to 3,000 PSI, with a midpoint of 2,500. Heavy dirt takes the midpoint to the top, 2,500 to 3,000 PSI, and never goes past 3,000, following the Bob Vila contractor's advice that higher pressure etches concrete. The GPM range is 2.5 to 4.0. Cleaning units run from 2,500 times 2.5, which is 6,250, to 3,000 times 4.0, which is 12,000. The top of the range, 3,000 PSI, is above the 2,500 gas line, so the power type is gas. The nozzle is the 25 degree green nozzle, or a surface cleaner for the flat area. The notes add two steps the pressure alone cannot do: apply detergent with the black soap nozzle first, and pre-treat the oil stains with a degreaser.

What the finder does not do. It does not estimate cleaning time, because no published source gives a reliable square-feet-per-hour rate that holds across machines, dirt, and technique, and inventing one would put a made-up number in the result. It does not size a machine for roofs, which should never be pressure washed at all: asphalt shingles need a soft wash, and the finder has no roof option on purpose. It does not adjust for surface age or condition beyond its warnings: weathered wood, loose paint, crumbling mortar, and oxidized siding all need less pressure than the chart, and the honest response is to test a hidden spot and start low.

What your result means

The PSI range is a working band, not a target. Start at the low end and move up only if the dirt stays put. The low end cleans light dirt on a sound surface; the high end is for dirt that resists the low end. If the low end works, you are done: extra pressure adds risk and nothing else. Every surface in the finder has a ceiling above its range, and the warning names it. For a car the ceiling is 2,000 PSI. For a pine or cedar deck it is 1,500. For concrete the working range tops out at 3,000, and above 3,500 you risk pitting the surface and exposing aggregate.

The GPM range sets the speed of the job. PSI breaks dirt loose; GPM carries it away and covers area. Simpson puts it the same way: PSI exerts the pressure to strip or scrub off the dirt, while GPM is the rinsing power that washes the dirt away. A machine with high PSI and low GPM cuts a narrow clean stripe and leaves you rinsing forever. A machine with moderate PSI and high GPM clears a wide path in each pass. When two machines cost the same, the one with more GPM usually finishes the job faster, which is why the finder shows the flow range beside the pressure range instead of hiding it.

Cleaning units are the honest comparison. One number lets you compare machines fairly: a 2,300 PSI machine at 1.2 GPM delivers 2,760 cleaning units, while a 2,000 PSI machine at 2.0 GPM delivers 4,000. The lower-PSI machine cleans faster. The finder reports a range because both inputs are ranges, and the range is wide on purpose: it shows how much the machine's flow matters. Use cleaning units to compare machines, and use the PSI range to protect the surface. The two numbers answer different questions, and you need both.

The nozzle matters as much as the machine. The nozzle and its spray pattern create the pressure at the surface, in Simpson's words, and a narrow tip held close concentrates more force on one spot than a wide tip at higher pressure. The finder names one nozzle per surface: the 40 degree white nozzle for cars, decks, siding, and furniture, and the 25 degree green nozzle for fences, brick, and concrete. The full nozzle guide below covers all five tips, including the black soap nozzle, which is the only tip that applies detergent. Never use the 0 degree red nozzle on paint, wood, vinyl, or any surface you care about: Simpson warns that its force will penetrate soft materials.

The power type is a starting point, not a brand. Electric covers every surface except heavy concrete and brick work and large flat areas, and it is quieter, lighter, and easier to store. Gas covers the rest, with the flow that large areas need. Either way, check the machine's rated PSI and GPM against the finder's ranges, not the maximum figures on the box: some machines advertise a maximum PSI measured with no nozzle fitted, and the working pressure at the wand is lower. A machine whose rated figures sit inside the finder's range is the right machine, whatever its maximum claims.

The warning is the most important line on the page. Every surface fails in a specific way, and every failure is permanent. Wood furs and splinters. Paint lifts. Vinyl cracks. Mortar washes out. Concrete etches and pits. The warning names the failure for your surface and the pressure where it starts, so you can recognize the line before you cross it. If your surface is old, weathered, or already damaged, treat the warning's ceiling as too high and stay well under it.

Pressure washer PSI by surface

The table below is the finder's whole chart in one place: the safe PSI range, the flow range, the nozzle, and the pressure never to exceed on each surface. The PSI ranges are the moderate-dirt ranges; light dirt uses the low half and heavy dirt uses the high half, as the How it works section explains.

SurfacePSI rangeGPMNozzleNever exceed
Car or truck1,200 to 1,9001.4 to 2.040 degree white2,000 PSI
Wood deck500 to 1,2001.5 to 2.040 degree white1,500 PSI
Concrete driveway2,000 to 3,0002.5 to 4.025 degree green3,500 PSI
Siding (vinyl)1,300 to 1,6001.5 to 2.040 degree white2,000 PSI
Patio furniture1,200 to 2,0001.2 to 2.040 degree white2,000 PSI
Wood fence1,500 to 2,0001.5 to 2.525 degree green2,000 PSI
Brick or masonry2,000 to 3,0002.0 to 3.025 degree green3,000 PSI

Three rows deserve a closer look. The wood deck row is the most conservative in the table, and deliberately so: sources disagree on deck pressure more than on any other surface, with some guides going as high as 2,500 PSI, while professional cleaners who wash decks for a living stay between 500 and 1,200 PSI for softwood. The finder follows the cleaners, because a deck cleaned at 900 PSI can always get a second pass, while a deck furred at 2,500 PSI needs sanding. The concrete row tops out at 3,000 PSI even for heavy dirt, following the Bob Vila contractor's warning that higher pressure etches concrete; other sources allow up to 3,500 PSI for heavy stains, and the finder treats 3,500 as the damage ceiling rather than a working pressure. The siding row is vinyl siding at 1,300 to 1,600 PSI; painted wood and stucco stay lower, at 1,200 to 1,500 PSI, and the finder says so in its warning.

Pressure washer nozzle guide

Nozzles are color coded by spray angle, and the colors are the same across most brands. The guide below follows Simpson's published nozzle chart. The angle sets how wide the fan is: a narrow fan concentrates the machine's full pressure on a small spot, and a wide fan spreads it. That is why the nozzle matters as much as the machine, and why stepping down one angle at a time is the safe way to add cleaning power.

NozzleAngleUse it for
Red0 degreesA concentrated spot for tar and gum on sidewalks, loose paint, and rust flakes on steel. Simpson warns its force will penetrate soft materials.
Yellow15 degreesA narrow fan for removing paint and mildew, heavy oxidation, and grime on hard surfaces. Sound, unpainted brick only.
Green25 degreesGeneral cleaning and rinsing: concrete, brick, fences, and decks. The all-round nozzle for hard surfaces.
White40 degreesA wide fan for cars, siding, windows, decks, and furniture. The starting nozzle for anything delicate.
BlackLow pressureApplying detergent. Cleaning solutions cannot be applied with the four high-pressure tips.

Two habits prevent most nozzle damage. First, always start with the white 40 degree nozzle, standing back, and step down one angle only if the dirt stays put. Simpson's advice for siding is to start further away and slowly approach the wall, making sure only dirt and grime are being removed, and the same rule works on every surface. Second, never use the black soap nozzle to rinse and never use a high-pressure tip to apply soap: the soap injection valve only opens with the low-pressure tip, so detergent applied through a green or white tip never leaves the tank. Apply soap with black, let it sit, then switch to the working nozzle and rinse.

Common mistakes to avoid

Buying the biggest PSI on the shelf. More pressure is not better. Above the level a surface tolerates, you stop cleaning and start removing the surface, and wood, paint, and mortar do not grow back. Simpson says household jobs should not need a machine larger than 3,000 PSI. Most homes need far less: everything except concrete and brick sits below 2,000 PSI, which is why a mid-range electric machine covers the great majority of household cleaning.

Judging a machine by PSI alone. A 3,000 PSI machine at 1.2 GPM delivers 3,600 cleaning units. A 2,200 PSI machine at 2.0 GPM delivers 4,400, and finishes the same driveway faster. Bob Vila's testers found the same thing in practice: when PSI is the same, an additional gallon per minute makes an enormous difference in cleaning power, but an increase of 500 PSI does not make much difference. Compare cleaning units, not PSI, when you choose between machines.

Using the red nozzle on anything you care about. The 0 degree red nozzle concentrates the machine's full pressure on a pinpoint. It cuts into wood, strips paint, etches concrete, and punches through vinyl. It has real uses, on tar, gum, rust, and loose paint on hard surfaces, but it should never touch a car, a deck, siding, or furniture. If the green nozzle is not shifting the dirt, the answer is detergent and a second pass, not the red nozzle.

Holding the wand still. A stationary stream removes progressively more material from one spot, which is why pausing mid-stroke produces the tiger striping on decks and driveways that people blame on the machine. Keep the wand moving in smooth, overlapping passes, and never pause on one spot to attack a stain. For a stain, pre-treat with detergent, let it sit, and wash the whole area evenly.

Spraying siding upward. Spraying up under vinyl siding drives water behind the panels, where it soaks the sheathing and feeds mold. Always spray downward, work from the bottom up when applying soap so dirty streaks do not set on dry siding, and rinse from the top down. Keep the wand at least a foot from the wall, and never aim at vents, windows, or electrical fixtures.

Skipping the test spot. Every surface in the finder has a range because surfaces vary: a ten-year-old deck is not a new deck, and sun-baked siding is not new siding. A thirty-second test on a hidden spot tells you more than any chart. Test at the low end of the range, check the spot when it dries, and only then commit to the whole surface. The test costs a minute. The repair costs a weekend.

Frequently asked questions

What PSI pressure washer do I need for a car?

Use 1,200 to 1,900 PSI with a 40 degree white nozzle, keeping the wand at least 12 inches from the paint. Family Handyman gives that range, and warns that anything over 2,000 PSI with a narrow nozzle can damage paint. Use the 25 degree green nozzle only for wheels and caked-on mud, never on paint, and never aim at seals, sensors, decals, or an engine bay.

What PSI is safe for a wood deck?

Use 500 to 1,200 PSI for a softwood deck, with a 40 degree white nozzle, spraying with the grain and keeping the wand moving. Never go above 1,500 PSI on pressure-treated pine or cedar: above that the water raises the grain and leaves a furred, splintery surface that only sanding fixes. Hardwood tolerates the 25 degree green nozzle, but the pressure ceiling is the same.

How much PSI do I need for a concrete driveway?

Use 2,000 to 3,000 PSI with a 25 degree green nozzle or a surface cleaner, at 2.5 to 4.0 GPM. A contractor quoted by Bob Vila advises at least 2,000 PSI to lift dirt off concrete and no higher than 3,000 PSI to avoid etching it. Above 3,500 PSI you risk pitting the concrete and exposing aggregate. For oil stains, pre-treat with a degreaser instead of adding pressure.

What are cleaning units, and why do they matter?

Cleaning units are PSI multiplied by GPM, and they measure how fast a machine cleans. A 2,000 PSI machine at 2.0 GPM delivers 4,000 cleaning units, while a 3,000 PSI machine at 1.2 GPM delivers only 3,600, so the lower-PSI machine finishes the job faster. Compare cleaning units when you choose between machines, and use the PSI range to protect the surface.

Is more PSI always better?

No. Once the pressure is enough to break the bond between dirt and surface, extra PSI only adds risk, and cleaning speed comes from water flow instead. Too much pressure furs wood decks, lifts car paint, cracks vinyl siding, washes out brick mortar, and etches concrete, and none of those failures is reversible. The right pressure is the lowest one that lifts the dirt, plus detergent and a second pass when the dirt resists.

Electric or gas pressure washer: which should I buy?

Electric covers most household jobs: household electric washers run 1,500 to 3,000 PSI with 1.5 to 2.5 GPM, which covers cars, decks, siding, fences, and furniture. Gas is the right choice above 2,500 PSI and for large flat concrete or brick areas, because gas washers run 2,500 PSI and up with 2.5 to 4.0 GPM, and the extra flow finishes big areas faster. Simpson adds a frequency rule: electric suits smaller jobs used once or twice a year, gas suits larger jobs and more frequent use.

Which nozzle should I use for delicate surfaces?

Use the white 40 degree nozzle, which spreads the spray into a wide fan and is the gentlest high-pressure tip. Simpson recommends it for most siding materials, for windows, and for cars, where it says to use only the white nozzle or the black soap nozzle. Start with the white nozzle standing back, and step down to the 25 degree green nozzle only if the dirt stays put. Never use the 0 degree red nozzle on a delicate surface.

Sources

Every figure on this page comes from one of the sources below, each accessed 19 November 2026. Where sources disagree, the page says so and follows the more conservative figure.

  • Family Handyman: pressure washing a car — car range 1,200 to 1,900 PSI, 25 degree tip for wheels and mud, 40 degree tip for vehicle surfaces, over 2,000 PSI risky, never closer than 12 inches. Accessed 19 November 2026.
  • Bob Vila: how to pressure wash a driveway — concrete needs at least 2,000 PSI and no more than 3,000 PSI to avoid etching, 4.0 GPM ideal and 2.5 GPM enough for smaller jobs, surface cleaner sizes and requirements. Accessed 19 November 2026.
  • Bob Vila: electric vs gas pressure washer — cleaning units are PSI multiplied by GPM, household electric 1,500 to 3,000 PSI with 1.5 to 2.5 GPM, gas seldom under 2,500 PSI with 2.5 to 4.0 GPM, 1,500 PSI and about 1.5 GPM more than enough for cars. Accessed 19 November 2026.
  • Bob Vila: best pressure washers for cars — car recommendation 1,400 to 2,000 PSI with 1.5 to 2.5 GPM, nozzle 25 degrees or wider, tip at least a foot from the surface. Accessed 19 November 2026.
  • Simpson: frequently asked questions — nozzle color guide (red 0 degrees, yellow 15, green 25, white 40, black soap), white nozzle for siding and cars, soap only with the black nozzle, cleaning units are PSI times GPM, household jobs need no more than 3,000 PSI, electric vs gas by job size and frequency. Accessed 19 November 2026.
  • Simpson instruction manual: pressure washer terminology — cleaning units defined as GPM multiplied by PSI. Accessed 19 November 2026.
  • Ace Handyman Services: what PSI pressure washer do I need — above 3,500 PSI on residential concrete risks pitting and aggregate exposure, wood deck maximum 1,500 PSI for pine and cedar, fence 1,500 to 2,000 PSI with aged boards splintering above 1,500. Accessed 19 November 2026.
  • Deca Cleaning: pressure washer PSI and GPM chart — per-surface PSI and GPM ranges for cars, furniture, siding, fences, decks, brick, and driveways, with a precaution for each surface. Accessed 19 November 2026.
  • The Honest Reviewers: what PSI pressure washer do I need — per-surface chart, deck furring above 1,800 PSI, concrete etching from a narrow nozzle held close, electric machines falling short on large flat concrete for lack of flow. Accessed 19 November 2026.
  • GF Cleaning Services: pressure washing PSI for surfaces — wood decks and fences at 500 to 1,200 PSI, softwoods needing less, furring and lines from rushing the work. Accessed 19 November 2026.
  • Ryobi: best pressure washers for Australian homes — surface cleaner covering a wider area and avoiding the stripe pattern of a single lance, 40 degree nozzle for cars, 25 or 40 degree for timber decks. Accessed 19 November 2026.
  • Repco: how to use an electric pressure washer — nozzle colors and uses, black 65 degree soap nozzle, start with the 40 degree nozzle and work up, clean furniture before the deck underneath it. Accessed 19 November 2026.