RC LiPo Battery Runtime Calculator
Estimated runtime
16 minutes
Last reviewed: 20 November 2026. Reviewed every 180 days; next review due 19 May 2027.
How to use the RC LiPo Battery Runtime Calculator
How long will my RC battery last? This RC battery runtime calculator answers that for your car, truck, crawler, drone, plane, or boat. A 5000mAh pack lasts about 16 minutes in a 1/10 truck at a 15 amp average, about 48 minutes in a crawler at 5 amps, and only about 4 minutes in a fast RC boat at 60 amps: the same pack gives wildly different runtimes because the average current draw is different. This calculator starts from your vehicle, fills in a typical average draw for it, and checks your pack's C rating against that draw.
- Pick your vehicle. Choose 1/10 scale buggy or truck, 1/8 scale buggy, rock crawler or trail truck, FPV drone or quad, RC airplane, or RC boat. The preset fills in a typical average draw and shows its typical range and usual pack size. Pick Custom setup if your build is unusual and enter your own draw.
- Enter the capacity and cell count. Type the milliamp-hour number on the pack, for example 5000, then pick 1S, 2S, 3S, 4S, or 6S. Each LiPo cell is 3.7 volts nominal, so a 2S pack is 7.4 volts, a 3S pack is 11.1 volts, a 4S pack is 14.8 volts, and a 6S pack is 22.2 volts. Capacity and draw set the runtime; cell count sets the voltage and watt-hours.
- Check the average draw. Change the preset figure if you have measured your own draw with a wattmeter, an ESC log, or a current sensor. This is the average over a whole run or flight, not the full-throttle peak: a 5-inch quad that pulls over 140 amps at full throttle may average only 20 amps across a freestyle flight.
- Enter the C rating and the discharge limit. The C rating is the number on the pack, for example 50C. The calculator multiplies it by the capacity to find the pack's safe continuous draw and warns you if your setup exceeds it. Leave the discharge limit at 80%, the standard rule: never use more than 80% of a LiPo pack.
- Read your result. You get the estimated runtime, usable capacity, watt-hours, average watts, C-rating safety check, sessions per charge, and packs per hour. Read the C-rating line before you run.
This calculator is one of the free tools on Tools Elite. Every figure on this page comes from a published source listed at the bottom. If you charge at the field from a power bank, our Power Bank Capacity Planner works out what size bank you need. The calculator gives estimates for general guidance, so always check the manufacturer's specifications for your battery, motor, and speed control before you buy or run.
How it works
The calculator works in four steps: it finds the usable capacity, divides it by the average draw to get the runtime, multiplies capacity by voltage to get watt-hours, and checks the draw against the pack's C-rating limit.
Usable capacity. Divide the milliamp-hours by 1,000 to get amp-hours, then multiply by the discharge limit, 80% by default. A 5000mAh pack gives 4,000mAh of usable capacity, and a 2200mAh pack gives 1,760mAh. The 80% rule is the standard LiPo guidance: never use more than 80% of a pack, because discharging further strains the cells and the pack's cycle life drops sharply. ProModeler's three rules of thumb for LiPo care put it first: do not discharge beyond 80% of rated capacity.
Runtime. Runtime in minutes equals usable capacity in amp-hours divided by average current draw in amps, times 60. FliteTest states the formula exactly this way: flight time equals battery capacity times battery discharge, divided by average amp draw, times 60. The average draw is the whole game: double the average and the runtime halves, whatever the pack says on the label.
Watt-hours and watts. Watt-hours are capacity in amp-hours times nominal voltage, and they are the honest way to compare packs of different voltages: a 5000mAh 2S pack holds 37 watt-hours, while a 5000mAh 6S pack holds 111 watt-hours. Average watts are average amps times nominal voltage: 25 amps at 7.4 volts is 185 watts, while 60 amps at 14.8 volts is 888 watts.
C-rating check. The safe continuous draw is the C rating times the capacity in amp-hours. Grepow defines it plainly: discharge current in amps equals C times amp-hours, so a 5 amp-hour pack rated at 20C can safely deliver 100 amps. If your draw is above the limit, the result is a warning. If it is above 80% of the limit, the result is a caution, because full-throttle peaks run well above the average. A 5000mAh 25C pack can safely deliver 125 amps, and a 2200mAh 35C pack can deliver 77 amps, the same figure the Rocky Mountain Modeleers use in their worked example. Note that the label overstates the real capability: one 2026 guide reports that measured C ratings typically come in at 30 to 50% of the printed figure.
Worked example 1: a 1/10 truck, 5000mAh 2S at 25 amps. Take the Traxxas Slash VXL, whose Velineon 3300kV motor draws 25 amps continuous. Usable capacity is 5000 times 0.8, which is 4 amp-hours. Runtime is 4 divided by 25, times 60, which is 9.6 minutes. The full pack would last 12 minutes drained completely. Watt-hours are 5 times 7.4, which is 37. The 25C pack's safe limit is 25 times 5, which is 125 amps, so 25 amps is only 20% of it. RC Tech Tips works the same example and gets the same 9.6 minutes, and notes that half-throttle driving at 12.5 amps gives 19.2 minutes.
Worked example 2: a drone, 2200mAh 3S at 15 amps. Usable capacity is 2200 times 0.8, which is 1.76 amp-hours. Runtime is 1.76 divided by 15, times 60, which is 7.04 minutes, shown as 7 minutes. Watt-hours are 2.2 times 11.1, which is 24.4. The 45C pack's safe limit is 45 times 2.2, which is 99 amps. At 20 amps the same math gives 5.3 minutes, matching FliteTest's example of a 2200mAh pack at 20 amps giving 5.28 minutes at 80% discharge.
What the calculator does not do. It does not measure your pack's real capacity, which falls with age, cold, and hard use. It does not model voltage sag, which cuts the usable capacity on high-draw setups. And it does not know your throttle finger: two drivers with the same car and pack can get runtimes 30% apart. Treat the result as a planning estimate, then measure one real run and correct the draw.
What your result means
Estimated runtime. The time from a full pack to the safe discharge limit, at the average draw you entered. Plan your session around it, and set a timer a minute shorter: a transmitter timer or a phone stopwatch costs nothing and saves the pack. If the runtime is under 5 minutes, the calculator adds a note saying so, because a sub-5-minute runtime usually means the pack is too small for the setup or the draw is very high.
Usable capacity and theoretical runtime. At the default 80% limit, a 5000mAh pack gives 4,000mAh and a 2200mAh pack gives 1,760mAh. The remaining 20% stays in the pack as a reserve that protects the cells. When your charger finishes a charge cycle, check how many milliamp-hours it put back: if that number is regularly above 80% of the label, you are running the pack too far down, and the fix is a shorter timer. The theoretical runtime shows how long the pack would last drained to zero, which you should never do: the gap between the two runtimes, 2.4 minutes on a 5000mAh pack at 25 amps, is the reserve that keeps the cells above 3.0 volts.
Watt-hours and watts. Milliamp-hours alone mislead across voltages: a 5000mAh 6S pack holds three times the energy of a 5000mAh 2S pack. Average watts tell you how hard the system works: a crawler uses 37 watts, while a boat at 60 amps and 14.8 volts uses 888 watts.
C-rating check. Green means your average draw sits comfortably under the pack's safe continuous limit. Amber means you are using more than 80% of the limit, with little margin for the peaks that run two to three times the average. Red means the average alone exceeds what the pack can safely deliver, and the pack will run hot, sag under load, and wear out fast. The fix is a pack with a higher C rating, a pack with more capacity, or a setup that draws less current: a smaller prop, a lower KV motor, or gentler gearing.
Sessions per charge and packs per hour. Sessions per charge divides the runtime by the typical session for your vehicle: a 5-minute race heat for a 1/10 buggy, a 10-minute main for a 1/8 buggy, a 60-minute trail session for a crawler, a 5-minute flight for a drone, an 8-minute flight for a plane, and a 5-minute run for a boat. Packs per hour divides 60 minutes by the runtime: a 9.6-minute runtime means about 6.3 packs for an hour of driving, while a 48-minute crawler runtime means about 1.3 packs. Pack count turns an abstract runtime into the number of batteries in your bag.
RC vehicle presets explained
Every preset carries a typical average draw, a typical pack, and a typical session length, drawn from published runtimes and manufacturer figures wherever those exist. A preset is a starting point, not a measurement: replace it with your measured draw as soon as you have one.
| Vehicle | Typical average draw | Typical pack | Typical session |
|---|---|---|---|
| 1/10 scale buggy or truck | 10 to 25 amps | 2S 5000mAh | 5-minute race heat |
| 1/8 scale buggy | 20 to 50 amps | 4S 5000mAh | 10-minute main |
| Rock crawler or trail truck | 3 to 8 amps | 2S 5000mAh | 60-minute trail session |
| FPV drone or quad | 15 to 30 amps | 4S 1500mAh | 5-minute flight |
| RC airplane | 10 to 20 amps | 3S 2200mAh | 8-minute flight |
| RC boat | 40 to 120 amps | 4S 5000mAh | 5-minute run |
1/10 scale buggy or truck, 15 amps default. At the hard end, the Traxxas Slash VXL's Velineon 3300kV motor draws 25 amps continuous, which RC Tech Tips uses as the full-throttle figure for a 5000mAh pack. At the gentle end, published runtimes imply a much lower average: a 5000mAh pack gives 15 to 30 minutes in a 1/10 car, and 20 to 25 minutes of gentle bashing works out to about 10 to 12 amps average. The 15 amp default gives 16 minutes, inside the published band.
1/8 scale buggy, 25 amps default. The 1/8 class usually runs a 4S 4000 to 6000mAh pack with a motor of about 1,000 watts and a speed control rated above 80 amps continuous, per RC Universe. A 10-minute main on a 5000mAh pack works out to about 24 amps average at 80% discharge, which is where the 25 amp default comes from. This preset is a labeled assumption built from the race-length math and the published hardware figures.
Rock crawler or trail truck, 5 amps default. Crawlers are the lowest-draw vehicles in the hobby: low speed, tall gearing, and long pauses between obstacles mean the motor spends most of its time barely working. The range runs from 3 amps, which gives 80 minutes on a 5000mAh pack, to 8 amps, the figure a published LiPo calculator uses for its crawler example. The 5 amp default gives 48 minutes.
FPV drone or quad, 20 amps default. A 5-inch freestyle quad cruises at 18 to 30 amps, per Freetooler, and Minihover puts the typical average at 15 to 30 amps, with racing quads drawing 30 amps and more. The same quad hovers at only about 6 amps total and pulls about 140 amps at full throttle, per Hibaan's drone power model, which is why the average depends so heavily on flying style. Long-range rigs cruise at 8 to 15 amps and fly 15 to 25 minutes, so pick Custom setup and enter 10 amps for those.
RC airplane, 15 amps default. FliteTest's Power Pack C example uses 20 amps, giving 5.28 minutes on a 2200mAh pack at 80% discharge, which sets the hard end of the range. Gentle sport flying at half throttle roughly halves the draw, which sets the 10 amp end. The 15 amp default gives 7 minutes on the standard 3S 2200mAh pack. This range is a labeled assumption built from the FliteTest figure.
RC boat, 60 amps default. Boats are the thirstiest RC models by a wide margin. RCexplained reports that high-power boat and ducted-fan setups draw about 120 amps continuously, on packs of 4000 to 6000mAh, which is the top of the preset's range. The 60 amp default gives 4 minutes on a 5000mAh 4S pack, a typical fast-electric run length. Check the current with a wattmeter after a prop change.
Cell count and voltage
The S number on a LiPo pack is the number of cells wired in series, and it sets the pack voltage. Every standard LiPo cell has the same five voltages worth knowing: 3.7 volts nominal, the label voltage and the average across a run; 4.2 volts fully charged; 3.8 volts for storage; 3.3 volts as the practical cutoff where you stop; and 3.0 volts as the absolute minimum, below which the cell is usually damaged for good. Traxxas states the cell voltage plainly: LiPo packs are composed of flat 3.7 volt cells. Grepow gives the same headline figures, and Rotorama's manual adds the two working figures: end-of-flight 3.5 volts per cell, storage 3.8 volts per cell.
| Pack | Nominal | Fully charged | Storage | Stop (3.3V per cell) | Minimum (3.0V per cell) |
|---|---|---|---|---|---|
| 1S | 3.7V | 4.2V | 3.8V | 3.3V | 3.0V |
| 2S | 7.4V | 8.4V | 7.6V | 6.6V | 6.0V |
| 3S | 11.1V | 12.6V | 11.4V | 9.9V | 9.0V |
| 4S | 14.8V | 16.8V | 15.2V | 13.2V | 12.0V |
| 6S | 22.2V | 25.2V | 22.8V | 19.8V | 18.0V |
Two things about this table surprise newcomers. More cells do not mean more runtime on their own: a 5000mAh 2S pack and a 5000mAh 6S pack last the same time at the same current draw, because runtime depends on capacity and draw. What the 6S pack gives is three times the voltage, three times the power, and three times the watt-hours. And the working band is narrow: half a volt per cell separates a healthy stop at 3.5 volts from permanent damage at 3.0 volts. LiHV packs are the exception: high-voltage cells charge to 4.35 volts per cell instead of 4.2, so the full-charge and storage voltages in the table do not apply to them.
LiPo safety: the numbers that protect your pack
A LiPo pack is safe when it is charged, run, and stored inside its limits, and dangerous when it is pushed outside them. The limits are few, they are published by the makers, and every one of them is a number you can check with a meter.
Never discharge below 3.0 volts per cell. Grepow states the safe minimum as typically 3.0 volts per cell, and Rotorama's manual is blunter: below 3.0 volts, permanent damage may occur. Traxxas warns that over-discharging a LiPo will cause irreparable damage and may cause battery failure. In practice never get near 3.0 volts: stop at 3.3 volts per cell, where most low-voltage alarms are set. Traxxas builds low-voltage detection into all its speed controls, set to alert below 3.2 volts per cell, but the speed control reads total pack voltage, not individual cells, so one weak cell can still fall below the floor while the pack total looks fine.
Store at 3.8 volts per cell. Rotorama's manual gives storage voltage as 3.8 volts per cell for storage of 14 days or longer. Grepow puts the optimal storage range at 3.7 to 3.85 volts per cell. Traxxas says to store packs at 50% capacity and warns not to store them discharged, because a pack stored flat for longer than 7 days may over-discharge on its own. Use your charger's storage mode: it charges or discharges the pack to the right voltage by itself.
Always balance charge, with a LiPo charger. A LiPo pack is balanced when each cell is charged to the same voltage, and Traxxas explains that balance charging gives the longest runtime from each charge and extends the pack's overall life by preventing over-discharging of a single weak cell. Never charge a LiPo with a NiMH charger or a NiMH charging mode: Traxxas states this in capitals in its battery guide, and its LiPo article warns that failing to use a LiPo balance charger can result in explosion, fire, and personal injury. Charge at or below the rate printed on the pack, and use 1C if no rate is printed: for a 5000mAh pack, 1C is 5 amps.
Charge where a fire cannot spread. Always charge in a fire-retardant container, on a non-flammable surface such as concrete, with nothing flammable nearby, and never leave a charging pack alone. Traxxas says never to charge batteries in your model, on wood, cloth, carpet, or any other flammable material. Inspect the pack before every charge: look for loose leads, damaged insulation, swelling, or a deformed case, and never charge a pack that is puffed or damaged. Retire a swollen pack through your local battery disposal route, never in household trash.
Common mistakes to avoid
Using the full-throttle peak as the average. A 5-inch quad pulls about 140 amps at full throttle but averages 15 to 30 amps across a flight; a 1/10 truck's motor may be rated for 25 amps continuous but average 12 to 15 amps across a bash. Enter the peak and the calculator gives you a runtime for a run that never happens: flat-out from start to finish.
Planning on 100% of the pack. The label capacity is not the usable capacity. Planning a flight to the last milliamp-hour means landing on empty cells, which is exactly how packs get damaged. The 80% rule exists because the last 20% is where the voltage falls off a cliff. Set the timer for the 80% runtime and treat the rest as reserve, not as flying time.
Ignoring the C rating. A pack can have plenty of capacity and still be wrong for the setup. A 2200mAh 10C pack can safely deliver only 22 amps, so a 60 amp setup will cook it even though the runtime math looks fine. Check the C-rating line on every result, and if the pack comes back hot, the margin was not enough.
Comparing packs by milliamp-hours across voltages. A 2200mAh 6S pack holds 48.8 watt-hours, more energy than a 5000mAh 2S pack at 37 watt-hours, even though its milliamp-hour number is less than half. When you compare packs of different cell counts, compare watt-hours, which the calculator shows on every result.
Running to the low-voltage cutoff every time. The cutoff is a safety net, not a fuel gauge. Traxxas sets its detection at 3.2 volts per cell, and it reads total pack voltage, so an unbalanced pack can hide a dying cell. Set a timer for the 80% runtime and stop on the timer, with the cutoff as the backup it was designed to be.
Frequently asked questions
How long will a 5000mAh LiPo battery last in an RC car?
A 5000mAh LiPo lasts about 15 to 30 minutes in a 1/10 scale RC car: roughly 20 to 25 minutes bashing gently, 10 to 15 minutes racing hard, and about 9.6 minutes at a steady full-throttle 25 amps. The exact time comes from the formula in this calculator: usable capacity divided by average amps, times 60. At 15 amps average, a 5000mAh pack gives 16 minutes using 80% of the pack. Driving style matters more than the label: full throttle all the time can cut the runtime in half.
How do you calculate RC battery runtime?
Divide the usable capacity in amp-hours by the average current draw in amps, then multiply by 60 to get minutes. Usable capacity is 80% of the label, because you should never drain a LiPo completely. For a 5000mAh pack at 25 amps: 5 amp-hours times 0.8 is 4 amp-hours, divided by 25 amps is 0.16 hours, times 60 is 9.6 minutes. The hard part is the average draw: measure it with a wattmeter, an ESC log, or a current sensor, or use one of this calculator's vehicle presets as a starting point.
What does the 80% rule mean for LiPo batteries?
The 80% rule says to use no more than 80% of a LiPo pack's capacity on a run or flight, landing or stopping with about 20% left. Discharging further strains the cells, and the pack's cycle life drops sharply once you regularly go past 80%. The same rule appears in RC guides as a voltage limit: stop when any cell reaches about 3.3 volts, and never let a cell drop below 3.0 volts, where the damage is usually permanent. This calculator applies the 80% rule by default, and you can change the limit if you want to see the difference.
What C rating do I need for my RC car?
Your pack's safe continuous draw is its C rating times its capacity in amp-hours, and that number must be above your setup's average draw, with headroom for peaks. A 5000mAh 25C pack can safely deliver 125 amps; a 2200mAh 35C pack can deliver 77 amps. Work out the C rating you need by dividing your average draw by the capacity in amp-hours: a 60 amp draw on a 2200mAh pack needs at least 27C, so a 35C pack covers it with margin. This calculator checks your draw against your pack's limit and warns you if you are over it or close to it.
How long does an FPV drone battery last?
A 5-inch freestyle quad typically flies 4 to 7 minutes on a 1300 to 1550mAh pack, and a racing quad only 2 to 5 minutes at full pace. The average draw is what decides it: a freestyle quad cruises at about 18 to 30 amps, while the same quad can pull over 140 amps at full throttle, so hard flying drains a pack in a fraction of the gentle-flight time. For a 1500mAh 4S pack at a 20 amp average, the calculator gives 3.6 minutes using 80% of the pack. Long-range rigs fly 15 to 25 minutes because they carry much bigger packs and cruise at only 8 to 15 amps.
What voltage should I store my LiPo batteries at?
Store LiPo packs at about 3.8 volts per cell, which is 7.6 volts for a 2S pack, 11.4 volts for 3S, 15.2 volts for 4S, and 22.8 volts for 6S. That is roughly half charged: Traxxas says to store packs at 50% capacity. Never leave a pack fully charged or fully empty on the shelf for more than a few days, and use your charger's storage mode to bring the pack to the right voltage. A pack stored flat can drop below the safe minimum on its own and be ruined before you use it again.
Why does my RC car run for less time than the calculator says?
The most common reason is that the real average draw is higher than the number you entered: full-throttle bursts, tall grass, steep hills, and a binding drivetrain all push the average up, and a pack that is old or cold delivers less than its label capacity. Measure the real average by timing a run and noting how many milliamp-hours your charger puts back, then divide that by the run time in hours. If the measured average is much higher than the preset, use the measured number: the calculator is only as accurate as the draw you give it.
Sources
Every figure on this page comes from one of the sources below, each accessed 20 November 2026. Where a preset range is a labeled assumption built from published runtimes and hardware figures rather than a single measured average, the page says so.
- Traxxas: Battery Basics — flat 3.7-volt LiPo cells; 2S 7.4V, 3S 11.1V, 4S 14.8V; balance charging; low-voltage detection below 3.2V per cell..
- Traxxas: LiPo Batteries — always use a LiPo balance charger; store at 50% capacity in a fire-retardant container; do not store discharged for longer than 7 days..
- Grepow: What Is the C Rating on a LiPo Battery — C rating equals discharge current divided by capacity; discharge current equals C times amp-hours; 5Ah at 20C delivers 100A..
- Grepow: What Is a 4S LiPo Battery — absolute minimum 3.0V per cell; stop at 3.3V to 3.5V per cell; 5000mAh 50C delivers 250A..
- Grepow: Complete Guide to 6S LiPo Batteries — 6S nominal 22.2V, fully charged 25.2V, storage 22.8V (3.8V per cell); maximum continuous amps equals C rating times capacity..
- Rotorama: LiPo Battery User Manual — nominal 3.7V, maximum 4.20V, storage 3.8V, end-of-flight 3.5V, minimum 3.0V per cell; current equals capacity times C..
- FliteTest: How to Estimate the Flight Time of a Battery — flight time equals capacity times discharge, divided by average amp draw, times 60; 2200mAh at 20A gives 5.28 minutes at 80%..
- ProModeler via Tekno RC Forums: How to Care for LiPo Batteries — do not discharge beyond 80% of rated capacity; stop the recharge at 95%; store packs at 3.80V per cell..
- ChinaHobbyLine: RC Battery Life — 5000mAh in a 1/10 truck gives 20 to 25 minutes bashing gently and 10 to 15 minutes racing hard; rule of thumb 15 to 30 minutes..
- RC Tech Tips: What Is the Longest Lasting RC Battery — Traxxas Slash VXL Velineon 3300kV motor draws 25 amps continuous; (5000mAh divided by 25A) times 80% equals 9.6 minutes; half throttle 12.5A gives 19.2 minutes..
- Hibaan: Drone Flight Time Calculator — 5-inch FPV quad hovers at about 6A total and pulls about 140A at full throttle; 4S 1500mAh pack stores 22.2 watt-hours..
- Freetooler: Drone Flight Time Calculator — 6S 5-inch freestyle build draws 18 to 30A in cruise; long-range rig cruises at 8 to 15A; 80% depth of discharge is the conventional limit..
- Minihover: How Long Do FPV Drone Batteries Last — racing quads draw 30A and more for 2 to 5 minutes; freestyle builds manage 4 to 7 minutes on 1300 to 1550mAh packs; long-range platforms fly 15 to 25 minutes..
- RC Universe: Motor, ESC, and Battery Explanation — ESC sizing: 40A for most 1/10 setups, 60A for heavy-duty 1/10, 80A for light-duty 1/8, 120A for midrange 1/8, 150 to 200A for the biggest 1/8 setups..
- RC Universe: LiPos and Questions, 1/8 Electric Buggy — 1/8 buggy usually runs 4S 4000 to 6000mAh; motor around 1,000 watts; ESC above 80A continuous with 200A burst..
- RCexplained: How RC Boats and EDF Jets Can Pull 120A Reliably — high-power boats and jets draw about 120 amps continuously on 4000 to 6000mAh packs; 120A from a 4000mAh pack is a 30C discharge rate..
- Rocky Mountain Modeleers: Power System Selection — maximum safe current equals C rating times capacity; 35C 2200mAh pack gives 77A..
- UAVmodel: LiPo Battery C-Ratings — label C ratings are marketing numbers; measured real C ratings typically run 30 to 50% of the label..
- LiPo Battery Calculator: RC Rock Crawler Example — crawler example uses a 5000mAh 3S pack at an 8A average draw; runtime formula uses 80% depth of discharge..