Skip to content

Firewood BTU Calculator

Verified Last reviewed: 21 November 2026. Page history

All heat values are per full cord of seasoned wood at about 20% moisture, from the Penn State Extension table (Heating with Wood: An Introduction, Table 1). A full cord is a stack 4 feet high, 8 feet long, and 4 feet deep: 128 cubic feet. Wet wood delivers less heat than the table value.

The 16 species in the Penn State Extension table, hottest first. Pick "My own wood" for a species the table does not cover, such as pine or fir.

Full cords, from 0.05 to 100. A face cord of 16-inch pieces is about one third of a full cord, so enter 0.33 for one face cord.

Efficiency turns gross heat into usable heat. Penn State Extension rates an open fireplace at 10 to 20%, a modern wood stove at 80% or more, and a pellet stove at 90%.

If you know how much heat you need, enter it here and the tool works out how many cords to buy. The target is usable heat delivered to the room, after efficiency. Leave blank to skip it.

What you pay for one full cord, delivered or picked up. Enter it to see the total cost and the cost per million BTU. Leave blank to skip it.

Total heat in your wood

How the numbers were worked out

      This tool estimates the heat in firewood from the Penn State Extension table and the numbers you enter, for general guidance only. Heat values differ between published tables by a few percent, and the heat you actually get depends on the moisture of your wood, how tightly it is stacked, and your appliance. Never burn treated, painted, or stained wood. Have your chimney inspected every year by a certified sweep.

      Free to use — no sign-up, no paywall. Spotted a mistake? Tell us — we fix reported errors within 24 hours.

      Your inputs stay in your browser: every calculation runs on your device, and nothing you type is sent to our servers.

      A cord of seasoned red oak holds 24.0 million BTU of heat, and a cord of Osage orange holds 30.7 million BTU, the most of any species in the Penn State Extension table. In a modern wood stove at 80% efficiency, 3 cords of red oak deliver 57.6 million BTU of usable heat. Enter your species, cords, and appliance above for your total heat, usable heat, species comparison, and cords needed for a heat target.

      Last reviewed: 21 November 2026. Reviewed every 180 days; next review due 19 May 2027.

      How to use the Firewood BTU Calculator

      A cord of firewood is not a fixed amount of heat. A cord of Osage orange holds 30.7 million BTU, while a cord of red and silver maple holds 18.7 million BTU, and that gap of 12 million BTU is the difference between a warm house and a cold one on the same order of wood. This calculator answers three questions that every wood-burning household asks in autumn: how much heat is in the wood you have, which species gives the most heat for the money, and how many cords you need to buy for the heat you want. It uses the published heat-value table from Penn State Extension, it works in million BTU per full cord of seasoned wood at about 20% moisture, and it shows every step of the arithmetic so you can check the answer by hand.

      The calculator is built around one table and three simple multiplications. The table gives the heat per cord for 16 common hardwood species. The first multiplication turns your species and your cords into gross heat. The second applies your appliance efficiency to give usable heat, the heat that actually reaches the room. The third, when you enter a heat target, divides the target by the usable heat per cord to tell you how many cords to buy. Nothing is hidden: the species table is printed in full below, the efficiency figures come from Penn State Extension, and the results page shows the working line by line.

      To get your result, follow these steps:

      1. Pick your wood species. The list holds the 16 species in the Penn State Extension table, hottest first, from Osage orange at 30.7 million BTU per cord down to red and silver maple at 18.7 million BTU per cord. If your wood is a species the table does not cover, such as pine, fir, or spruce, pick "My own wood" and enter its heat value from a published extension table. The calculator treats your own figure honestly: it carries no rank in the Penn State table, and the results say so.
      2. Enter how many cords. Enter full cords, from 0.05 to 100. A full cord is a stack 4 feet high, 8 feet long, and 4 feet deep, which is 128 cubic feet of stacked wood. If you buy by the face cord, convert first: a face cord of 16-inch pieces is about one third of a full cord, so enter 0.33 for one face cord. A face cord of 12-inch pieces is one quarter of a cord, so enter 0.25. The calculator accepts fractions, so a half cord is 0.5 and a quarter cord is 0.25.
      3. Pick what you burn it in. This is the step most firewood charts skip, and it matters more than the species. An open fireplace turns only about 15% of the heat in the wood into heat in the room. A modern wood stove manages 80% or more. A pellet stove burns at 90%. Pick your appliance from the list, or pick "Gross heat" to see the heat in the wood with no appliance loss at all. If you know your appliance rating from its rating plate, pick "My own efficiency figure" and enter it.
      4. Enter a heat target, if you have one. This step is optional. If you know how much heat you need, for example 60 million BTU of delivered heat for the winter, enter it here and the calculator works out how many cords to buy. The target is treated as usable heat, the heat delivered to the room after efficiency, because that is the number that heats your home. The answer rounds up to whole cords, because that is how firewood is sold.
      5. Enter the price per cord, if you want the cost. This step is also optional. Enter what you pay for one full cord, delivered or picked up, and the calculator shows the total cost, the cost per million BTU of gross heat, and the cost per million BTU of usable heat. The cost per million BTU of usable heat is the fair way to compare two offers: cheap wood that burns in an open fireplace can cost more per unit of heat than dearer wood in a modern stove.
      6. Read the comparison table. Below the headline result, the calculator shows all 16 species ranked by heat, with each species shown as a percentage of your wood. If your wood is red oak, Osage orange shows as 127.9% and red and silver maple shows as 77.9%. The table is the fastest way to answer the question "which firewood burns hottest" and the question "how much am I giving up by burning the cheaper wood" in the same glance.

      Three worked examples show the arithmetic. First, 3 cords of red oak in a modern wood stove: the gross heat is 24.0 times 3, which is 72.0 million BTU, and the usable heat is 72.0 times 80%, which is 57.6 million BTU. Second, 2 cords of Osage orange in a modern stove: the gross heat is 30.7 times 2, which is 61.4 million BTU, and the usable heat is 61.4 times 80%, which is 49.12 million BTU. Third, a target of 60 million BTU of usable heat from red oak in a modern stove: each cord delivers 24.0 times 80%, which is 19.2 million BTU of usable heat, so the cords needed are 60 divided by 19.2, which is 3.125, rounded to 3.13 cords, and you buy 4 cords.

      How the calculator works

      The calculator runs on one table and four formulas. The table is Penn State Extension Table 1 from Heating with Wood: An Introduction, which lists the energy value of an air-dried cord of common hardwood of the Northeastern United States in million BTU, at an assumed moisture content of 20%. The table is the work of Hank Stelzer, published in 2017, and it was re-checked against the Penn State Extension page on 21 November 2026. Every heat figure in this calculator comes from that table, except for a heat value you enter yourself, which is marked as your own figure throughout the results.

      The first formula is gross heat. Gross heat equals heat per cord times cords. The heat per cord comes from the table, and the cords are what you enter. For 3 cords of red oak, the gross heat is 24.0 times 3, which is 72.0 million BTU. For 2 cords of hickory, the gross heat is 28.0 times 2, which is 56.0 million BTU. Gross heat is the heat locked in the wood, before any of it is lost up the chimney. It is the figure firewood charts quote, and it is the right figure for comparing species, but it is not the heat that warms your house.

      The second formula is usable heat. Usable heat equals gross heat times appliance efficiency. The efficiency figures come from the same Penn State Extension article: an open fireplace is 10 to 20% efficient, so the calculator uses the 15% midpoint; a modern wood stove is 80% or more efficient, so the calculator uses the 80% floor; a pellet stove burns at 90% efficiency. For 3 cords of red oak in a modern stove, the usable heat is 72.0 times 80%, which is 57.6 million BTU. The same 3 cords in an open fireplace give 72.0 times 15%, which is 10.8 million BTU. The appliance changes the answer by a factor of more than five, which is why the calculator asks what you burn the wood in.

      The third formula is cords for a target. Cords needed equals the heat target divided by usable heat per cord. Usable heat per cord is the table value times the efficiency: for red oak in a modern stove, it is 24.0 times 80%, which is 19.2 million BTU per cord. A target of 60 million BTU needs 60 divided by 19.2, which is 3.125 cords, shown as 3.13 cords, and the calculator tells you to buy 4 cords, because firewood is sold by the cord and 3 cords would leave you short. When the division comes out whole, the calculator says so: a target of 57.6 million BTU from red oak in a modern stove needs exactly 57.6 divided by 19.2, which is exactly 3 cords.

      The fourth formula is cost per million BTU. Cost per million BTU of gross heat equals price per cord divided by heat per cord. Cost per million BTU of usable heat equals price per cord divided by usable heat per cord. At $250 a cord, red oak costs 250 divided by 24.0, which is $10.42 per million BTU of gross heat, and 250 divided by 19.2, which is $13.02 per million BTU of usable heat in a modern stove. The usable figure is the one to compare between offers, because it is the price of the heat that reaches the room.

      The calculator also shows two comparison figures. The first is heat against red oak, the usual benchmark in firewood talk: each species is shown as a percentage of the 24.0 million BTU in a cord of red oak. Osage orange is 30.7 divided by 24.0, which is 127.9%. White oak is 25.7 divided by 24.0, which is 107.1%. Red and silver maple is 18.7 divided by 24.0, which is 77.9%. The second is a heating oil comparison, using Penn State's own equivalence: one cord of seasoned northern red oak produces the same amount of heat as 159 gallons of fuel oil. The 72.0 million BTU in 3 cords of red oak is therefore about 72.0 divided by 24.0 times 159, which is 477 gallons of heating oil.

      Every figure the calculator prints is computed from the rounded values shown on the page, so the printed equations reconcile. Usable heat is computed from the rounded gross heat, and cords for a target are computed from the rounded usable heat per cord. Money rounds to the cent, heat rounds to two decimals in million BTU, and percentages round to one decimal. The rounding rule is half-up, the same rule a hand calculation uses.

      The firewood heat table

      The table below is the Penn State Extension table in full, with the rank, the heat band, and the heat against red oak added. The heat band is the calculator's own grouping: High is 24.0 million BTU per cord or more, Medium is 20.0 to under 24.0, and Low is under 20.0. Nine of the 16 species are High, five are Medium, and two are Low. The rank uses competition ranking, so tied species share a rank and the next rank skips: hornbeam and black birch share 4th place at 26.8 million BTU per cord, and the next species, honey locust, is 6th.

      RankSpeciesMillion BTU per cordHeat bandHeat vs red oak
      1Osage orange30.7High127.9%
      2Hickory28.0High116.7%
      3Ironwood / hop hornbeam27.3High113.8%
      4Hornbeam / blue beech26.8High111.7%
      4Black birch26.8High111.7%
      6Honey locust26.7High111.3%
      7White oak group25.7High107.1%
      8Sugar maple24.0High100.0%
      8Red oak group24.0High100.0%
      10White ash23.6Medium98.3%
      10Yellow birch23.6Medium98.3%
      12Hackberry20.8Medium86.7%
      13Birch, paper, gray, and river20.3Medium84.6%
      14Black walnut20.2Medium84.2%
      15Black cherry19.9Low82.9%
      16Maple, red and silver18.7Low77.9%

      Source: Penn State Extension, Heating with Wood: An Introduction, Table 1 (Hank Stelzer, 2017). Values are million BTU per full cord of air-dried wood at an assumed moisture content of 20%. The table covers common hardwood of the Northeastern United States. Penn State notes that heating values may differ in other reports due to differences in methodology and the individual trees tested, which is why this calculator uses one table throughout instead of mixing tables.

      Three things in the table deserve attention. First, the gap between the top and the bottom is large: Osage orange at 30.7 million BTU per cord holds 64% more heat than red and silver maple at 18.7, because 30.7 divided by 18.7 is 1.64. You need 1.6 cords of red and silver maple to match the heat in one cord of Osage orange. Second, the middle of the table is crowded: the nine species from white ash at 23.6 up to hickory at 28.0 sit within 4.4 million BTU of each other, so for most of the common hardwoods the species matters less than the seasoning and the appliance. Third, the two oaks bracket the middle: white oak at 25.7 is 7.1% hotter than red oak at 24.0, which is why white oak usually costs more per cord and is worth more per cord when the price gap is small.

      The table has limits, and the calculator is open about them. It covers hardwood only: no pine, fir, spruce, or cedar appears in it, because Penn State's table is a hardwood table. If you burn softwood, use the "My own wood" option with a figure from an extension table that covers your species. Virginia Tech, for example, lists white pine at 14.3 million BTU per cord and hemlock at 15.9 million BTU per cord, both well below the lowest hardwood in the Penn State table. The table also covers the Northeastern United States: the same species grown elsewhere can differ slightly, and individual trees differ too. Treat each figure as the best published value for the species, not as a laboratory test of your load.

      Why one cord can hold nearly twice the heat of another

      The reason is density, not chemistry. A pound of oven-dry wood holds about the same heat whatever the species: the USDA Forest Service, Forest Products Laboratory puts it at approximately 8,600 BTU per pound of oven-dry hardwood, and slightly higher, about 9,150 BTU per pound, for the resinous conifers. The heat per pound barely changes from species to species. What changes is how many pounds fit in a cord. A cord of dense Osage orange weighs far more than a cord of light red and silver maple, so it holds far more heat, even though each pound of the two woods holds about the same.

      That is why the heat table is really a density table in disguise. The hottest woods are the heaviest: Osage orange, hickory, and ironwood are among the densest North American hardwoods. The coolest woods are the lightest: red and silver maple, black cherry, and black walnut are light woods that seasoned quickly and burn quickly. When you lift a split log, you are feeling its heat value: a heavy log of the same size holds more heat than a light one. The USDA Forest Service figure also explains why the net usable heat per pound is lower than the gross figure: burning the hydrogen in a pound of dry wood makes about 0.55 pounds of water, and vaporizing that water costs about 660 BTU, and hot flue gases carry away about 690 BTU more, leaving about 7,250 BTU of net usable heat per pound of dry wood.

      Density also explains why the table values are per cord and not per pound. Firewood is sold by volume, by the cord, so the buyer needs to know the heat per cord. If firewood were sold by weight, the species would hardly matter: a ton of any dry hardwood holds roughly the same heat. But a cord is a fixed volume, and dense wood packs more pounds into that volume. That is the whole story of the heat table, and it is also why a seller who charges the same price per cord for maple as for oak is selling you less heat for the same money.

      One more density point matters when you compare offers. A cord is 128 cubic feet of stacked wood, but only about 80 to 90 cubic feet of that is solid wood: the rest is air between the pieces. How tightly the wood is stacked changes how much solid wood you get, which changes the heat you get. A loosely stacked cord holds less wood and less heat than a tightly stacked cord of the same species. When you buy, measure the stack: height times width times length, divided by 128, is the number of cords. Penn State gives the example itself: a stack 4 feet high, 8 feet wide, and 8 feet long is 256 cubic feet, which divided by 128 is 2 cords.

      What seasoned means: the 20% moisture basis

      Every figure in the Penn State table, and every figure this calculator produces, is on one stated basis: air-dried wood at an assumed moisture content of 20%. That basis is not a detail. It is the whole reason the table works. Fresh-cut wood is mostly water by weight: Penn State notes that freshly cut northern red oak can have a moisture content of 60 to 80%. Burning that wood means boiling off the water before the wood itself can burn, and the heat spent boiling water goes up the chimney instead of into the room.

      Moisture content is measured as a percentage of the oven-dry weight of the wood. Wood at 20% moisture holds 20 pounds of water for every 100 pounds of dry wood. Wood at 60% moisture holds 60 pounds of water for every 100 pounds of dry wood, three times as much. The water does not just dilute the heat: it costs heat to remove. Vaporizing a pound of water takes about 1,000 BTU, and the steam carries more heat up the flue as it is heated to flue temperature. The USDA Forest Service reckons each pound of steam carries about 1,210 BTU up the flue. Green wood therefore delivers far less usable heat per cord than the table value, and it also burns cooler, smokes more, and lays down more creosote in the chimney.

      Seasoning is the process of bringing the moisture down to about 20%. The wood is cut, split, and stacked off the ground, with the top covered and the sides open to the air, and left to dry. Penn State says the best time to harvest a tree for firewood is February or March, when the air is crisp and the trees have not begun to bud, and that some species may require more than six months of seasoning. Dense woods take longest: oak and hickory need a year or more, and two years is better for large rounds. Light woods dry faster: ash and soft maple can be ready in six months to a year. Splitting matters more than waiting: a round dries very slowly, while split pieces dry from every face.

      How do you know the wood is seasoned? The reliable test is a moisture meter, pressed into a freshly split face: seasoned wood reads 20% or lower. Without a meter, look for cracked ends, bark pulling away from the wood, lighter weight than a green piece of the same size, and a hollow knock when two pieces are struck together. Wood that hisses, bubbles at the ends, or throws off clouds of steam in the fire is not seasoned, whatever the seller said. If you buy wood advertised as seasoned, check a few pieces with a meter before you pay for the load: the table value you just calculated only applies to wood that is actually dry.

      Kiln-dried wood is the other way to buy dry wood. A kiln dries the wood in a large oven, so it has a much lower moisture content than air-dried wood, and it is ready to burn on delivery. Penn State notes that kiln-dried wood can be more expensive, and quotes $80 to $100 a cord for kiln-dried delivered wood in 2017 figures. Prices vary by place and year, so the calculator never assumes a price: enter the price you are actually quoted and it works out the cost per million BTU for your offer.

      Gross heat vs usable heat: the appliance decides

      Gross heat is the heat in the wood. Usable heat is the heat in the room. The gap between them is the appliance, and it is the largest single factor in the whole calculation, larger than the species and larger than the seasoning. Penn State Extension puts the numbers plainly: a fireplace is only 10 to 20% efficient at creating heat, while modern wood stoves are 80% or more efficient. A pellet stove burns at 90% efficiency. The same cord of wood delivers five times as much usable heat in a modern stove as in an open fireplace.

      Work it through with 3 cords of red oak, which hold 72.0 million BTU of gross heat. In an open fireplace at 15% efficiency, the usable heat is 72.0 times 15%, which is 10.8 million BTU. In a modern wood stove at 80%, the usable heat is 72.0 times 80%, which is 57.6 million BTU. In a pellet stove at 90%, it would be 72.0 times 90%, which is 64.8 million BTU, though pellet stoves burn pellets rather than cordwood. The fireplace wastes 61.2 million BTU up the chimney. That is not a small loss: it is most of the heat you paid for.

      The fireplace number has a second sting. Penn State notes that if the flue is left open with no fire, a fireplace can have a negative impact on heating: warm room air goes up the chimney all day. A fireplace with the damper open and no fire is a hole in the roof. A modern stove avoids both losses: it burns the wood at a higher temperature, controls the airflow, and can have filters that remove pollutants, so more of the heat stays in the house and less pollution leaves it.

      The calculator's efficiency defaults are chosen to be fair, not flattering. The fireplace figure of 15% is the midpoint of Penn State's 10 to 20% range. The modern stove figure of 80% is the floor of Penn State's "80% or more", so a good stove may do better. The pellet figure of 90% is Penn State's own number. If your stove has a rated efficiency on its rating plate or in its manual, enter that figure with the "My own efficiency figure" option: a stove rated at 72% gives 72.0 times 72%, which is 51.84 million BTU from the same 3 cords of red oak, and the calculator will use your figure exactly.

      Usable heat is also the right basis for comparing wood with other fuels. A gallon of heating oil holds about 138,500 BTU of gross heat, but a furnace at 80% efficiency delivers about 110,800 BTU of usable heat per gallon. The Penn State equivalence used in this calculator, one cord of red oak equals 159 gallons of fuel oil, is a gross-heat comparison: 24.0 million BTU divided by 159 gallons is about 150,900 BTU per gallon, which is the gross heat content Penn State assumes for fuel oil. Keep the basis straight when you compare: gross against gross, or usable against usable, never one against the other.

      How many cords do you need for a heat target

      The target mode turns the calculation around. Instead of asking what heat your wood holds, it asks how much wood your heat needs. Enter the heat you want in million BTU, and the calculator divides it by the usable heat per cord to give the cords needed, then rounds up to whole cords to buy. The target is usable heat, delivered to the room, because that is what a heat target means in practice: the heat your house needs, not the heat in the woodpile.

      The arithmetic is one division. Usable heat per cord is the table value times the efficiency. For red oak in a modern stove, that is 24.0 times 80%, which is 19.2 million BTU per cord. A target of 60 million BTU needs 60 divided by 19.2, which is 3.125 cords, shown as 3.13 cords, so you buy 4 cords. A target of 100 million BTU needs 100 divided by 19.2, which is 5.21 cords, so you buy 6 cords. A target of 57.6 million BTU needs exactly 57.6 divided by 19.2, which is exactly 3 cords, and the calculator says "exactly" only when the division comes out whole.

      The species changes the answer. For the same 60 million BTU target in a modern stove, Osage orange delivers 30.7 times 80%, which is 24.56 million BTU per cord, so the cords needed are 60 divided by 24.56, which is 2.44 cords, and you buy 3 cords. Red and silver maple delivers 18.7 times 80%, which is 14.96 million BTU per cord, so the cords needed are 60 divided by 14.96, which is 4.01 cords, and you buy 5 cords. The same heat target needs 3 cords of the hottest wood or 5 cords of the coolest, which is why the species matters most when you are buying to a target.

      The appliance changes the answer even more. For the same 60 million BTU target from red oak, a modern stove at 80% needs 3.13 cords, but an open fireplace at 15% delivers only 24.0 times 15%, which is 3.6 million BTU per cord, so the cords needed are 60 divided by 3.6, which is 16.67 cords, and you buy 17 cords. Nobody burns 17 cords through a fireplace in a winter, which is the point: an open fireplace is not a heating appliance, and the target mode makes that plain in a way a percentage never does.

      Where does a heat target come from? The honest answer is your own heating history. If you heated with oil last winter, take the gallons you burned and multiply by the usable heat per gallon from your furnace rating. If you heated with gas, take the therms from your bills: one therm is 100,000 BTU, so 600 therms is 60 million BTU of gross heat, and at 80% furnace efficiency that is 48 million BTU of usable heat. If you heated with electricity, take the kilowatt-hours: one million BTU is 293.07 kilowatt-hours, so 60 million BTU is 17,584 kilowatt-hours. If you have no history, the calculator cannot invent a target for you, and it does not try: the target field is optional, and the species and cords result stands on its own. Our Mini-Split BTU Sizer sizes electric heat room by room, and our Fuel Cost Calculator works out what a heating season costs in fuel, if you want to build the target from the other side.

      What firewood costs per million BTU

      Firewood is usually priced per cord, but heat is what you buy, so the price per cord is the wrong number to compare. Two offers at the same price per cord can differ by 64% in heat, and two offers at different prices per cord can be the same price per unit of heat. The cost per million BTU of usable heat is the fair comparison, and the calculator works it out from the price you enter.

      Take red oak at $250 a cord in a modern stove. The gross cost is 250 divided by 24.0, which is $10.42 per million BTU. The usable cost is 250 divided by 19.2, which is $13.02 per million BTU. Now take red and silver maple at $200 a cord in the same stove. The gross cost is 200 divided by 18.7, which is $10.70 per million BTU. The usable cost is 200 divided by 14.96, which is $13.37 per million BTU. The maple looks $50 a cord cheaper, but per unit of usable heat it is $0.35 per million BTU dearer. Over a 60 million BTU winter, the oak costs 60 times $13.02, which is $781.20, and the maple costs 60 times $13.37, which is $802.20. The cheaper wood costs $21 more for the same heat.

      The same test settles the Osage orange question. Osage orange at $350 a cord in a modern stove costs 350 divided by 24.56, which is $14.25 per million BTU of usable heat. That is dearer than red oak at $250 a cord, which is $13.02 per million BTU of usable heat, even though Osage orange is the hottest wood in the table. Heat per cord and value per dollar are different questions, and the hottest wood is only the best buy when its price per cord is less than its heat advantage. Osage orange at $300 a cord would cost 300 divided by 24.56, which is $12.21 per million BTU of usable heat, which beats the oak. The break-even price for Osage orange against $250 oak is 250 times 30.7 divided by 24.0, which is $319.79 a cord: below that, Osage orange is the better buy; above it, oak is.

      Price also interacts with the appliance. The same red oak at $250 a cord costs $13.02 per million BTU of usable heat in a modern stove, but in an open fireplace at 15% it costs 250 divided by 3.6, which is $69.44 per million BTU of usable heat. No firewood is cheap heat in an open fireplace. If you burn in a fireplace, the money is better spent on a stove insert than on a better species: the insert multiplies every cord you will ever burn.

      One caution about prices: firewood prices vary by place, by season, and by whether the wood is delivered, split, or stacked. The calculator never assumes a price and never quotes a live price. Enter the price you are actually offered, for the species actually offered, and compare on cost per million BTU of usable heat. And check the measure: a cord that is short by a quarter is a 25% price rise in disguise, whatever the sticker says.

      Features

      The full Penn State table, built in. All 16 species from Penn State Extension Table 1 are built into the calculator, with the heat value shown next to each species in the list. You pick the species and the calculator uses the published figure: 30.7 million BTU per cord for Osage orange, 24.0 for red oak, 18.7 for red and silver maple. No figure is typed in by hand at run time, so no figure can be mistyped.

      A custom species option. The Penn State table covers hardwood only. If you burn pine, fir, spruce, cedar, or any species the table does not list, pick "My own wood" and enter the heat value from a published extension table. The calculator uses your figure for every result, marks it as your own entry in the steps and the notes, and gives it no rank, because a rank only means something inside one table.

      Gross heat and usable heat, side by side. The headline result is the gross heat in your wood. The first result card is the usable heat after your appliance efficiency. Both are shown because both matter: gross heat compares species, usable heat heats the house. The steps show the multiplication that turns one into the other.

      Five appliance options. Modern wood stove at 80%, open fireplace at 15%, pellet stove at 90%, gross heat with no loss, and your own efficiency figure from 5% to 95%. The three named figures come from Penn State Extension, and the custom option takes the rating from your appliance plate. The fireplace option also triggers a warning that most of the heat goes up the chimney, with the numbers for your load.

      Cords for a heat target. Enter a target in million BTU and the calculator divides it by the usable heat per cord, shows the exact figure to two decimals, and tells you how many whole cords to buy. When the division comes out whole, it says "exactly". When the target would need more than 20 cords, it warns you to double-check the target before you buy.

      Cost per million BTU. Enter the price per cord and the calculator shows the total cost, the cost per million BTU of gross heat, and the cost per million BTU of usable heat. The usable figure is the fair comparison between offers, and it is the figure that settles whether the cheaper wood is actually cheaper heat.

      A full species comparison. Every result includes all 16 species ranked by heat, each shown as a percentage of your wood, with your wood highlighted. The comparison answers "which firewood burns hottest" and "how much heat am I giving up" in one table, and it is the same table whatever species you pick, so you can compare offers across species without re-running the tool.

      Honest warnings. The calculator warns you when the wood burns dangerously hot: Penn State Extension warns that burning large amounts of high-BTU wood like Osage orange or ironwood can burn through the bottom of some stoves, so the calculator says so for both species and suggests mixing with a milder wood. It warns you when low-heat wood means more frequent loading, telling you how many cords of your wood match one cord of Osage orange. It warns you when an order is large, giving the stacked volume in cubic feet so you can check the delivery. And it warns you when your custom heat value is unchecked, because an unchecked figure should never look like a published one.

      Every step shown. The results page lists the working in order: heat per cord, gross heat, usable heat, rank, cords for the target, cost, and the heating oil comparison. Each step prints the numbers it uses, so you can check the arithmetic with a pocket calculator. The notes underneath state the basis, the limits of the table, and the safety rules, in plain language.

      Use cases

      Buying firewood for the winter. A seller offers 3 cords of mixed oak at $250 a cord, and another offers 4 cords of red and silver maple at $200 a cord. Run both through the calculator in a modern stove. The oak holds 72.0 million BTU gross and 57.6 million BTU usable, and costs $750, which is $13.02 per million BTU of usable heat. The maple holds 74.8 million BTU gross and 59.84 million BTU usable, and costs $800, which is $13.37 per million BTU of usable heat. The maple order holds slightly more usable heat but costs $50 more, and per unit of heat the oak is the better buy. Without the calculator, the maple looks cheaper by $50 a cord.

      Deciding whether to burn the tree you just cut. A storm drops a black cherry in your yard, and you wonder whether it is worth cutting for firewood. Black cherry is 19.9 million BTU per cord, a low-heat wood, ranked 15th of 16. Two cords of it hold 39.8 million BTU gross, and in a modern stove deliver 31.84 million BTU of usable heat, about the same as 1.7 cords of red oak. It is worth cutting if the alternative is paying to haul it away, and the pleasant smell is a bonus, but it is not worth buying at oak prices. Our Tree Height Calculator measures the tree before you cut, and our Tree Benefits Calculator estimates what a living tree is worth standing, which is the other side of the decision.

      Checking a delivery. The truck leaves and you measure the stack: 4 feet high, 8 feet long, and 6 feet deep. That is 192 cubic feet, which divided by 128 is 1.5 cords. If you paid for 2 cords of white oak, you are half a cord short, which is 12.85 million BTU of gross heat missing, because 25.7 times 0.5 is 12.85. The calculator takes fractional cords, so enter 1.5 and see the heat you actually received, then take the numbers back to the seller.

      Planning a woodlot harvest. You own a few acres and cut your own firewood, and you want to know which trees to take. The comparison table ranks your species by heat, and the target mode tells you how many cords of each species your winter needs. Taking the low-value stems first is good forestry as well as good heating: Penn State notes that firewood harvesting is an excellent way to remove low-value stems, invasive species, or trees that cannot be harvested in commercial operations, and that cutting firewood helps prevent high-grading, the practice of cutting only high-value wood. Our Tree Planting Calculator plans the replacement planting, and our Pruning Calendar times the work through the year.

      Comparing wood with oil or gas. Your oil bill last winter was 400 gallons. At the EIA figure of 138,500 BTU per gallon, that is 55.4 million BTU of gross heat, and at 80% furnace efficiency it is 44.32 million BTU of usable heat. In a modern stove at 80%, red oak delivers 19.2 million BTU of usable heat per cord, so replacing that oil heat with wood needs 44.32 divided by 19.2, which is 2.31 cords, so buy 3 cords. At $250 a cord that is $750 of wood against the oil bill, and the calculator shows the heating oil equivalent for every load so the comparison is always in view.

      Burning a mixed load. Most delivered loads are mixed species. The calculator handles one species at a time, so run each species separately and add the results. Two cords of red oak and one cord of white ash hold 48.0 plus 23.6, which is 71.6 million BTU gross, and in a modern stove deliver 57.28 million BTU of usable heat, because 71.6 times 80% is 57.28. If you do not know the mix, run the load as the lowest-heat species in it: that gives a conservative figure, and any better wood in the pile is a bonus.

      Teaching a new wood burner. The worked steps are a teaching tool. A new burner who sees that 3 cords of red oak hold 72.0 million BTU gross but deliver only 10.8 million BTU in an open fireplace understands in one glance why the stove matters more than the species. A burner who sees that wet wood delivers less than the table value understands why the moisture meter matters. The calculator shows the working, not just the answer, so the lesson sticks.

      Burning safely: chimney and creosote

      Heat is only half the story of burning wood. The other half is the chimney, and the Chimney Safety Institute of America, the CSIA, publishes the guidance every wood burner should follow. The central fact is creosote: the black or brown residue that wood smoke leaves on the inside of the flue as it cools. Creosote is highly combustible, and it is the main cause of chimney fires. The CSIA lists restricted air supply, unseasoned wood, and cooler-than-normal chimney temperatures as the conditions that speed up creosote buildup, which is why the same seasoned wood that gives the most heat also gives the safest burn.

      The CSIA recommends an annual inspection of the chimney and venting system by a CSIA Certified Chimney Sweep, and the national standard, NFPA 211, requires chimneys, fireplaces, and vents to be inspected at least once a year for soundness, freedom from deposits, and correct clearances, with cleaning, maintenance, and repairs done if necessary. The inspection is the non-negotiable part. Cleaning follows when the inspection finds enough buildup: the CSIA recommends that masonry fireplaces be swept at 1/8 inch of sooty buildup, and sooner if there is any glaze present, because that much buildup is enough to cause a chimney fire. Factory-built fireplaces should be swept when any appreciable buildup occurs, because the deposits are acidic and can corrode the parts of the system.

      Wet wood makes creosote faster. Unseasoned wood burns cooler, and cooler smoke condenses more readily on the flue walls. Burning wet wood therefore costs you twice: less heat in the room, and more creosote in the chimney. The same goes for smoldering fires with the air control closed down, and for softwoods burned in quantity: Penn State advises limiting conifers like pine, fir, and spruce in heating use, because their secondary compounds can coat a chimney with tar, soot, and creosote, which may lead to a chimney fire if the chimney is not cleaned regularly.

      Three more safety rules come from Penn State Extension. Never burn toxic species like poison ivy, poison oak, or poison sumac, and never burn wood that has been treated or stained: burning them releases dangerous compounds. Never burn rotting or decomposing wood: it has high internal moisture, which reduces the heat and produces large amounts of ash and smoke, and not all fungal smoke is safe. And never burn large amounts of very high-BTU wood like Osage orange or ironwood in a stove that cannot take the heat: Penn State warns it can burn through the bottom of some stoves. Mix hot wood with milder wood, keep the air control down, and know your stove's limits.

      Finally, have the chimney inspected before the first fire of the season, not after it. Sweeps are busiest once the cold arrives, and a chimney fire in January is the worst time to learn that the flue was blocked or the liner was cracked. Book the inspection in late summer or early fall, burn seasoned hardwood, keep the damper open during a fire, and let the inspection tell you whether the chimney needs sweeping.

      Sources

      Penn State Extension, Heating with Wood: An Introduction (Table 1, Hank Stelzer, 2017; re-verified from the publisher page on 21 November 2026). Governs the heat-value table for all 16 species, the 20% moisture basis, the cord and face cord definitions, the appliance efficiency figures, the heating oil equivalence of one red oak cord to 159 gallons, the fresh-cut moisture range of 60 to 80% for northern red oak, and the safety warnings about toxic species, treated wood, rotting wood, and very high-BTU wood.

      USDA Forest Service, Forest Products Laboratory, Wood Fuel Combustion Practice (L. H. Reineke, Report No. R1666-18, 1947, reaffirmed 1956). Governs the heat content of oven-dry wood, approximately 8,600 BTU per pound for hardwood and about 9,150 BTU per pound for resinous conifers, the net usable heat of about 7,250 BTU per pound of dry wood after hydrogen moisture and stack losses, and the heat cost of vaporizing water at about 1,210 BTU per pound of steam.

      Chimney Safety Institute of America (CSIA), Preventing Chimney Fires and homeowner resources. Governs the annual inspection recommendation, the cleaning threshold of 1/8 inch of sooty buildup for masonry fireplaces, sooner if any glaze is present, the advice to sweep factory-built systems at any appreciable buildup, and the conditions that speed creosote buildup: restricted air supply, unseasoned wood, and cooler-than-normal chimney temperatures.

      Virginia Tech, Firewood, Facts, Follies and Forest Management (Brian Bond and Adam Downing). Used only for the two softwood figures quoted in this page, white pine at 14.3 million BTU per cord and hemlock at 15.9 million BTU per cord, because the Penn State table covers hardwood only. Softwood figures are never mixed into the Penn State table in this calculator.

      U.S. Energy Information Administration, Energy units and calculators explained. Governs the heating oil heat content of 138,500 BTU per gallon, the propane heat content of 91,452 BTU per gallon, the natural gas figures of 1,036 BTU per cubic foot and 100,000 BTU per therm, and the electricity conversion of 1 kilowatt-hour to 3,412 BTU.

      Frequently asked questions

      Which firewood has the most BTU per cord?

      Osage orange has the most heat of any species in the Penn State Extension table, at 30.7 million BTU per seasoned cord, followed by hickory at 28.0, ironwood and hop hornbeam at 27.3, and hornbeam and black birch at 26.8 each. Osage orange holds 27.9% more heat than a cord of red oak and 64% more than a cord of red and silver maple. It also burns very hot: Penn State Extension warns that burning large amounts of it can burn through the bottom of some stoves, so mix it with a milder wood and keep the air control down.

      How many BTU are in a cord of oak?

      A cord of red oak holds 24.0 million BTU and a cord of white oak holds 25.7 million BTU, both per full cord of seasoned wood at about 20% moisture, from the Penn State Extension table. Three cords of red oak hold 72.0 million BTU of gross heat, and in a modern wood stove at 80% efficiency they deliver 57.6 million BTU of usable heat. In an open fireplace at 15% efficiency the same 3 cords deliver only 10.8 million BTU. White oak is 7.1% hotter than red oak, so it is worth a higher price per cord up to that margin.

      What is a cord of firewood?

      A full cord is a stack of wood 4 feet high, 8 feet long, and 4 feet deep, which is 128 cubic feet of stacked wood including the air gaps between the pieces. To work out how many cords a stack holds, multiply its height, width, and length in feet and divide by 128: a stack 4 feet high, 8 feet wide, and 8 feet long is 2 cords. A face cord is a stack 4 feet high and 8 feet long but only one piece deep, usually 16 inches, so it holds about one third of a full cord. A face cord can hold from one quarter to one half of a full cord depending on the piece length.

      How many BTU do I actually get from a cord after stove efficiency?

      Multiply the gross heat per cord by your appliance efficiency. A cord of red oak holds 24.0 million BTU gross, so in a modern wood stove at 80% efficiency it delivers 19.2 million BTU of usable heat, in an open fireplace at 15% it delivers 3.6 million BTU, and in a pellet stove at 90% it would deliver 21.6 million BTU. A cord of Osage orange at 30.7 million BTU gross delivers 24.56 million BTU in a modern stove. The appliance changes the answer by a factor of more than five, which is why this calculator asks what you burn the wood in before it gives you a usable heat figure.

      How many cords do I need for the winter?

      Divide your heat target by the usable heat per cord. If your home needs 60 million BTU of delivered heat for the winter and you burn red oak in a modern stove, each cord delivers 19.2 million BTU of usable heat, so you need 60 divided by 19.2, which is 3.13 cords, and you buy 4 cords. The same target needs 3 cords of Osage orange or 5 cords of red and silver maple. To find your target, work back from last winter's fuel: 400 gallons of heating oil at 138,500 BTU per gallon is 55.4 million BTU of gross heat, and at 80% furnace efficiency that is 44.32 million BTU of usable heat.

      Does wet wood really give less heat?

      Yes, and by a large margin. Every figure in the Penn State table assumes air-dried wood at about 20% moisture. Freshly cut northern red oak can have a moisture content of 60 to 80%, and burning it means boiling off the water before the wood itself can burn: vaporizing a pound of water takes about 1,000 BTU, and the USDA Forest Service reckons each pound of steam carries about 1,210 BTU up the flue. Wet wood also burns cooler, smokes more, and lays down more creosote in the chimney. Season the wood until a moisture meter reads 20% or lower on a freshly split face, and check a few pieces before you pay for a load sold as seasoned.

      Is pine firewood bad for heating?

      Pine is a poor heating wood for two reasons. First, it holds much less heat per cord than dense hardwood: Virginia Tech lists white pine at 14.3 million BTU per cord and hemlock at 15.9, against 24.0 for red oak, so you need about 1.7 cords of white pine to match one cord of red oak. Second, Penn State Extension advises limiting conifers like pine, fir, and spruce in heating use, because their secondary compounds can coat a chimney with tar, soot, and creosote, which may lead to a chimney fire if the chimney is not cleaned regularly. Pine is fine for kindling and for quick fires in mild weather, but it is not a primary heating wood. This calculator covers it through the "My own wood" option: enter the heat value from an extension table for your species.

      How do I check my firewood is seasoned?

      The reliable test is a moisture meter pressed into a freshly split face: seasoned wood reads 20% or lower, which is the basis of the Penn State table. Without a meter, look for cracked ends, bark pulling away from the wood, lighter weight than a green piece of the same size, and a hollow knock when two pieces are struck together. Wood that hisses, bubbles at the ends, or throws off clouds of steam in the fire is not seasoned. Dense woods like oak and hickory need a year or more of drying after splitting, and two years is better for large rounds, while light woods like ash can be ready in six months to a year. Split the wood before stacking it: a round dries very slowly, while split pieces dry from every face.

      Page history
      • — Pre-isBasedOn snapshot (YMYL authority, Nov 2026) (saleem891@gmail.com)
      • — Pre-IA-remap snapshot: category population (live application 22 Nov 2026) (saleem891@gmail.com)
      • — Published (saleem891@gmail.com)